How to replace the brake pads on Chevrolet Colorado?

Begin the Brake Pad replacement by watching the master cylinder reservoir fluid level; no need to drain fluid if it stands at mid-range but fluid needs to be lowered to mid-range when above the mark. Lift the vehicle then disconnect the tire and wheel components. Trap the brake caliper in place with a large c-clamp touching both its backside to outboard pad while tightening until the pistons compress. Secure the brake caliper with heavy mechanic wire to shield the hydraulic brake hose when you withdraw the guide pin bolt from its lower position. Push brake caliper upward and take away both outer and inner brake pads. Replace old Brake Pad shims before you begin with new disc brake pads. Clean both the brake caliper needle and the mating surfaces. For used brake pads keep the shims and clean them with denatured alcohol until they are dry. Cover the brake caliper with mechanic wire and install new brake shims before putting in the outer Brake Pad then the inner Brake Pad. Hold up the caliper with mechanic wire during a low pivot to install it on the Brake Caliper Bracket. Fasten the lower caliper guide pin bolt by turning it to 64 nm (47 lb ft). Arrange the tire and wheel before lowering the vehicle. With the engine turned off apply the brake pedal steadily to 2/3rd depth and then let it return to its initial position. Keep pushing the brake pedal for 15 seconds during breaks to thoroughly position brake caliper pistons and pads correctly. Top the master cylinder reservoir to specification and perform break in procedure on pads and rotors.

How to replace the front disc brake pads on the 2500 Series on Chevrolet Tahoe?

In order to change the front disc brake pads on the 2500 series, the first step is to check the level of fluid in the brake master cylinder reservoir; if the level is above the midpoint between maximum-full and minimum allowable points, stop up fluid to the point of midway. Lift up the vehicle and take away the tire and wheel assembly. Use two large c-clamps through the brake caliper pistons while lifting the two caliper pistons using the clamps on the back side of the outboard Brake Pad, trying to push until the two pistons are fully retracted. Take out the brake caliper guide pin bolts and be sure to secure the caliper with heavy mechanic wire to prevent hydraulic flexible brake hose damage. Remove the brake pads from the brake caliper and take note of the Brake Pad wear sensor if it has one. Removing the brake caliper from the bracket. Throw away the old Brake Pad retaining springs and check the brake caliper. To install, fix brand new Brake Pad retaining springs to the calciper bracket, align the new disc brake pads, and remodel the brake caliper. Secure the caliper and guide pin bolts tightened with force of 108 nm (80 lb ft) and re-install the tire and the wheel assembly with the lowering of the vehicle. With the engine off, approach the brake pedal to approximately 2/3 of its travel and then slowly let it off. This is repeated until a firm pedal is achieved for properly seating the caliper pistons and brake pads. Lastly, top up the brake master cylinder reservoir with fresh break fluid to the proper limit and burnish the brake pads and discs.

OEM Chevrolet Brake Pad

Disc Brake Pad Set

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

245 Brake Pads found

View related parts
Chevrolet Brake Pads Part Number: 23399101
$310.07 MSRP: $607.07
You Save: $297.00 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Front Pads
- Position: Front
- Replaces: 23337277
Fits the following Chevrolet Models:
- Camaro | 2017-2024 | ZL1 | 8 Cyl 6.2 L GAS
View related parts
Chevrolet Brake Pads Part Number: 20829195
$125.60 MSRP: $263.16
You Save: $137.56 (53%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Rear Pads
- Position: Rear
- Replaced by: 19433094
Fits the following Chevrolet Models:
- Silverado 2500 HD | 2011-2015 | High Country, LT, LTZ, WT | 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
- Silverado 3500 HD | 2011-2015 | High Country, LT, LTZ, WT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
View related parts
Chevrolet Brake Pads Part Number: 84265875
$100.27 MSRP: $204.07
You Save: $103.80 (51%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Rear Pads
- Position: Rear
- Replaces: 88983902
Fits the following Chevrolet Models:
- Express 2500 | 2003-2017 | Base, LS, LT | 4 Cyl 2.8 L DIESEL, 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
- Express 3500 | 2003-2017 | Base, LS, LT | 4 Cyl 2.8 L DIESEL, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
View related parts
Chevrolet Brake Pads, Black, Rear Part Number: 84394374
$106.45 MSRP: $218.68
You Save: $112.23 (52%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit-Rear Disc Brake *Black; Disc Brake Hardware Kit; Rear Pads; Pad Kit, Brake
- Position: Rear
Fits the following Chevrolet Models:
- Express 2500 | 2018-2020 | Base, LS, LT | 4 Cyl 2.8 L DIESEL, 6 Cyl 4.3 L FLEX, 6 Cyl 4.3 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS
- Express 3500 | 2018-2020 | Base, LS, LT | 4 Cyl 2.8 L DIESEL, 6 Cyl 4.3 L FLEX, 6 Cyl 4.3 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Rear Pads Part Number: 89060331
$129.20 MSRP: $233.84
You Save: $104.64 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Brake Pads
- Position: Rear
Fits the following Chevrolet Models:
- Corvette | 2008 | Base | 8 Cyl 6.2 L GAS
View related parts
Chevrolet Front Pads Part Number: 85115093
$250.24 MSRP: $469.94
You Save: $219.70 (47%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Brake Pads
- Position: Front
Fits the following Chevrolet Models:
- Camaro | 2021-2022 | LS, LT, LT1 | 4 Cyl 2.0 L GAS, 6 Cyl 3.6 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Front Pads Part Number: 85115095
$235.39 MSRP: $426.04
You Save: $190.65 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Brake Pads; Pad Kit, Brakes
- Position: Front
Fits the following Chevrolet Models:
- Camaro | 2021-2022 | SS | 8 Cyl 6.2 L GAS
View related parts
Chevrolet Brake Pads Part Number: 85142725
$300.35 MSRP: $543.62
You Save: $243.27 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Front Pads
- Replaced by: 85713075
Fits the following Chevrolet Models:
- Corvette | 2020-2024 | E-Ray, Stingray, Z06 | 8 Cyl 5.5 L GAS, 8 Cyl 6.2 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L GAS
View related parts
Chevrolet Brake Pads Part Number: 85529064
$389.35 MSRP: $762.30
You Save: $372.95 (49%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Front Pads
- Replaced by: 85614851
Fits the following Chevrolet Models:
- Corvette | 2020-2024 | E-Ray, Stingray, Z06 | 8 Cyl 5.5 L GAS, 8 Cyl 6.2 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L GAS
View related parts
Chevrolet Brake Pads Part Number: 84263810
$159.18 MSRP: $308.93
You Save: $149.75 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Rear Pads
- Position: Rear
- Replaces: 22847817
Fits the following Chevrolet Models:
- Corvette | 2014-2019 | Stingray | 8 Cyl 6.2 L GAS
View related parts
Chevrolet Brake Pads Part Number: 85148032
$225.18 MSRP: $421.68
You Save: $196.50 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Pad Kit, Brakes
- Position: Front
Fits the following Chevrolet Models:
- Camaro | 2016-2024 | LS, LT, LT1 | 4 Cyl 2.0 L GAS, 6 Cyl 3.6 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Brake Pads Part Number: 87842603
$644.53 MSRP: $1061.73
You Save: $417.20 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Rear Pads
- Replaces: 86813586
Fits the following Chevrolet Models:
- Corvette | 2023-2024 | Stingray, Z06 | 8 Cyl 5.5 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Brake Pads Part Number: 84345385
$608.51 MSRP: $1002.40
You Save: $393.89 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake
- Position: Rear
Fits the following Chevrolet Models:
- Corvette | 2019 | ZR1 | 8 Cyl 6.2 L GAS
View related parts
Chevrolet Brake Pads Part Number: 86824349
$819.07 MSRP: $1349.26
You Save: $530.19 (40%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Front Pads
Fits the following Chevrolet Models:
- Corvette | 2023-2024 | Stingray, Z06 | 8 Cyl 5.5 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Brake Pads Part Number: 13553895
$170.52 MSRP: $320.22
You Save: $149.70 (47%)
ADD TO CART
Product Specifications
- Other Name: Pad Kit-Parking Brake Caliper; Pad Kit, Parking Brake Apply
- Replaces: 84935101
Fits the following Chevrolet Models:
- Corvette | 2020-2024 | E-Ray, Stingray, Z06 | 8 Cyl 5.5 L GAS, 8 Cyl 6.2 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L GAS
View related parts
Chevrolet Brake Pads Part Number: 84935101
$170.52 MSRP: $320.22
You Save: $149.70 (47%)
ADD TO CART
Product Specifications
- Other Name: Pad Kit-Parking Brake Caliper; Pad Kit, Parking Brake Apply
- Replaced by: 13553895
Fits the following Chevrolet Models:
- Corvette | 2020-2024 | E-Ray, Stingray | 8 Cyl 6.2 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L GAS
View related parts
Chevrolet Brake Pads Part Number: 22791925
$221.61 MSRP: $430.12
You Save: $208.51 (49%)
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Brake Pad Set, Disc Brake; Disc Brake Hardware Kit; Disc Brake Pad Set; Front Pads; Pad Kit, Brakes
- Position: Front
- Replaced by: 85148032
Fits the following Chevrolet Models:
- Camaro | 2016-2021 | LS, LT, LT1 | 4 Cyl 2.0 L GAS, 6 Cyl 3.6 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Rear Pads Part Number: 84859031
$144.96 MSRP: $306.46
You Save: $161.50 (53%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Brake Pads
- Position: Rear
- Replaces: 84394383
Fits the following Chevrolet Models:
- Express 3500 | 2018-2020 | Base, LS, LT | 4 Cyl 2.8 L DIESEL, 6 Cyl 4.3 L FLEX, 6 Cyl 4.3 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Brake Pads Part Number: 87827069
$98.31 MSRP: $206.15
You Save: $107.84 (53%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Rear Pads
- Replaces: 84259175, 22960232
Fits the following Chevrolet Models:
- Silverado 2500 HD | 2015-2019 | High Country, LT, LTZ, WT | 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
- Silverado 3500 HD | 2015-2019 | High Country, LT, LTZ, WT | 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
View related parts
Chevrolet Brake Pads Part Number: 19433093
$85.29 MSRP: $248.31
You Save: $163.02 (66%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Rear Pads
- Replaces: 20828610
Fits the following Chevrolet Models:
- Silverado 2500 HD | 2011-2014 | LT, LTZ, WT | 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
- Silverado 3500 HD | 2011-2015 | High Country, LT, LTZ, WT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL

| Page 1 of 13 |Next >

1-20 of 245 Results

Chevrolet Brake Pad

Choose OEM Brake Pad, you're making the optimal decision for superior quality and perfect performance. You can feel confident because each component goes through stringent quality checks. Every part is carefully built to comply with Chevrolet's factory specifications. You'll enjoy a smooth, worry-free installation that fits just right. At ChevyPartsDeal.com, you'll find it easy to get top-quality OEM Chevrolet Brake Pad. You can shop at highly competitive prices and protect your budget. All our genuine Chevrolet parts include a dependable manufacturer's warranty. You'll also appreciate our straightforward return policy and swift delivery services for extra convenience.

Chevrolet Brake Pad is made to grip the rotor hard and sacrifices speed in the name of quick safety of stoppage. Chevrolet is a legacy of 100 years of riding on the familiar on Monday and the exciting on Saturday, combining strong frames, intelligent cabins, and priceable enough, without any empty promises. Chevy invests that legacy on engines that inhale effortlessly on the highways and still pull trailers without any commotion. Its Super Cruise allows your hands to relax and sensors maintain lane cleanliness, reducing road-trip weariness. Chevy interiors put the buttons where the fingers are supposed, which means that a beginner masters the controls within minutes and the rest never hunt. Cargo is always roomy and lines remain crisp long after winter salt has done its worst. Warranties remain simple and new code is pushed into infotainment displays online with no trouble. Brake Pad attaches a steel backing plate with a friction compound of semi-metal, ceramic, or organic materials clamping rotors to up to 400-degree heat and converting the movement to manageable heat and eliminating deterioration during hard braking on mountain descents or city sprints. Select a type of Brake Pad by aligning the noise level, dust level, and rotor stress with your driving style. It suits all Chevy to even the weary pads and squeal of indicators before the grip is lost. Chevrolet users do not experience rotor distortion because they refuse to cheap out and instead install compounds that meet their commute requirements.

Chevrolet Brake Pad Parts and Q&A

Brake Pads, Front
19178358
Q: How to replace the brake pads on Chevrolet Colorado?
A:
Begin the Brake Pad replacement by watching the master cylinder reservoir fluid level; no need to drain fluid if it stands at mid-range but fluid needs to be lowered to mid-range when above the mark. Lift the vehicle then disconnect the tire and wheel components. Trap the brake caliper in place with a large c-clamp touching both its backside to outboard pad while tightening until the pistons compress. Secure the brake caliper with heavy mechanic wire to shield the hydraulic brake hose when you withdraw the guide pin bolt from its lower position. Push brake caliper upward and take away both outer and inner brake pads. Replace old Brake Pad shims before you begin with new disc brake pads. Clean both the brake caliper needle and the mating surfaces. For used brake pads keep the shims and clean them with denatured alcohol until they are dry. Cover the brake caliper with mechanic wire and install new brake shims before putting in the outer Brake Pad then the inner Brake Pad. Hold up the caliper with mechanic wire during a low pivot to install it on the Brake Caliper Bracket. Fasten the lower caliper guide pin bolt by turning it to 64 nm (47 lb ft). Arrange the tire and wheel before lowering the vehicle. With the engine turned off apply the brake pedal steadily to 2/3rd depth and then let it return to its initial position. Keep pushing the brake pedal for 15 seconds during breaks to thoroughly position brake caliper pistons and pads correctly. Top the master cylinder reservoir to specification and perform break in procedure on pads and rotors.
Brake Pads
25910432
Q: How to replace the front disc brake pads on the 2500 Series on Chevrolet Tahoe?
A:
In order to change the front disc brake pads on the 2500 series, the first step is to check the level of fluid in the brake master cylinder reservoir; if the level is above the midpoint between maximum-full and minimum allowable points, stop up fluid to the point of midway. Lift up the vehicle and take away the tire and wheel assembly. Use two large c-clamps through the brake caliper pistons while lifting the two caliper pistons using the clamps on the back side of the outboard Brake Pad, trying to push until the two pistons are fully retracted. Take out the brake caliper guide pin bolts and be sure to secure the caliper with heavy mechanic wire to prevent hydraulic flexible brake hose damage. Remove the brake pads from the brake caliper and take note of the Brake Pad wear sensor if it has one. Removing the brake caliper from the bracket. Throw away the old Brake Pad retaining springs and check the brake caliper. To install, fix brand new Brake Pad retaining springs to the calciper bracket, align the new disc brake pads, and remodel the brake caliper. Secure the caliper and guide pin bolts tightened with force of 108 nm (80 lb ft) and re-install the tire and the wheel assembly with the lowering of the vehicle. With the engine off, approach the brake pedal to approximately 2/3 of its travel and then slowly let it off. This is repeated until a firm pedal is achieved for properly seating the caliper pistons and brake pads. Lastly, top up the brake master cylinder reservoir with fresh break fluid to the proper limit and burnish the brake pads and discs.