How to replace the rear disc brake pads on Chevrolet Equinox?

Check the brake fluid level in the master cylinder reservoir before work. Remove brake fluid when the fluid is above midfield but below the highest and lowest acceptable mark. Position the vehicle on jack stands before you take out the tire and wheel unit. Use hand tools to take out the lower bolt of the brake caliper guide pin. Hold the guide pin with an open-end wrench but keep the brake caliper safe from contact to prevent brake pulsation during use. Set the brake caliper upward and place a solid wood block onto the brake pistons. Press all brake piston both clearly into its housing using the Brake Pad spreader tool or a similar tool. Take all Brake Pad components from the set including both pads and their springs but remove and discard only the old springs when replacing with new brake pads. Put new springs over both Brake Pad spots then place in inner and outer Brake Pad positions. Secure the brake caliper guide pin bolt at 27 nm (20 lb ft) while positioning the brake caliper into its installed setup. Turn off your engine and fit back the tire-wheel assembly. Press the brake pedal incrementally until it reaches 2/3 of its length and let go. Do this until the Brake Caliper Piston and pad correctly align inside the brake system. Refill the master cylinder reservoir and let the brake pads and rotors run-in.

How to replace the front disc brake pads on Chevrolet Equinox?

First thing that you should do in order to replace the front disc brake pads should be the inspection of the fluid level in the brake master cylinder reservoir; if it is at the midway point between maximum-full point and minimum allowable level watere is not required to be drained but if it is high, drain out to the midway point. Lift the vehicle and remove the tire and wheel assembly. Push a large c-clamp over the brake caliper body against the brake caliper outer Brake Pad and compress the Brake Caliper Piston completely into the brake caliper bore with a c-clamp. Prevent using air tools for the guide pin bolts; instead use hand tools and an open end wrench to hold the caliper guide pin lined when removing the lower brake caliper guide pin bolt. Lift the brake caliper towards you and locate the Brake Pad wear sensor, in order to install correctly, and remove the inner Brake Pad and outer Brake Pad and the upper and lower Brake Pad springs. In case of replacing brake pads, dispose of the old springs; insert, the inner Brake Pad and outer Brake Pad, and return the brake caliper back into the desired position. While holding the brake caliper, the pin of the guide with the help of a back up wrench, tighten the lower brake caliper guide pin bolt to 27 nm (20 lb ft). Reinstall the tire and wheel assembly, gradually press down the Brake Pedal to about 2/3rd of its travel distance with the engine off, then slowly release it until you work up through this cycle until afirm Brake Pedal is achieved to seat the Brake Caliper Piston and brake pads properly. Lastly, top up the master cylinder tank and burnish the brake pads and rotors.

OEM Chevrolet Equinox Brake Pad

Disc Brake Pad Set

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

12 Brake Pads found

View related parts
Chevrolet Equinox Brake Pads Part Number: 84121520
$105.01 MSRP: $203.80
You Save: $98.79 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Front Pads
- Position: Front
- Replaced by: 85144100
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2018-2021 Chevrolet Equinox | L, LS, LT, Premier | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L DIESEL, 4 Cyl 2.0 L GAS
View related parts
Chevrolet Equinox Brake Pads Part Number: 84259368
$74.70 MSRP: $142.14
You Save: $67.44 (48%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Rear Pads; Front Pads
- Position: Front
- Replaces: 23303281
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2018-2021 Chevrolet Equinox | L, LS, LT, Premier | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L DIESEL, 4 Cyl 2.0 L GAS
View related parts
Chevrolet Equinox Brake Pads Part Number: 23214903
$151.85 MSRP: $294.72
You Save: $142.87 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Front Pads
- Position: Front
- Replaces: 20877794
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2010-2017 Chevrolet Equinox | L, LS, LT, LTZ, Premier | 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Equinox Brake Pads Part Number: 20801538
$98.89 MSRP: $191.93
You Save: $93.04 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Disc Brake Pad Set; Rear Pads
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2010-2017 Chevrolet Equinox | L, LS, LT, LTZ, Premier | 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Equinox Brake Pads, Front Part Number: 19168899
$75.13 MSRP: $147.08
You Save: $71.95 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Front Disc Brake; Disc Brake Hardware Kit; Disc Brake Pad Set; Front Pads; Pad Kit, Brake
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2009 Chevrolet Equinox | LS, LT, LTZ, Sport | 6 Cyl 3.4 L GAS, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Equinox Brake Pads Part Number: 19168900
$64.47 MSRP: $100.99
You Save: $36.52 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Disc Brake Pad Set; Rear Pads
- Position: Rear
- Replaces: 19149904
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2009 Chevrolet Equinox | LS, LT, LTZ, Sport | 6 Cyl 3.4 L GAS, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Equinox Brake Pads Part Number: 13237753
$141.04 MSRP: $255.28
You Save: $114.24 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Front Pads
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2010 Chevrolet Equinox | LS, LT, LTZ | 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L GAS
View related parts
Chevrolet Equinox Brake Pads Part Number: 85143237
$78.16 MSRP: $151.70
You Save: $73.54 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Disc Brake Hardware Kit; Rear Pads
- Replaces: 84474215, 84650556
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2024 Chevrolet Equinox | L, LS, LT, Premier, RS | 4 Cyl 1.5 L GAS
View related parts
Chevrolet Equinox Brake Pads Part Number: 85129514
$87.26 MSRP: $169.36
You Save: $82.10 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Front Pads
- Replaces: 84775616
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2022-2024 Chevrolet Equinox | LS, LT, Premier, RS | 4 Cyl 1.5 L GAS
View related parts
Chevrolet Equinox Brake Pads Part Number: 85127904
$166.78 MSRP: $323.69
You Save: $156.91 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Rear Pads
- Position: Front
- Replaces: 13527902, 13595651
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2018-2020 Chevrolet Equinox | L, LS, LT, Premier | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L DIESEL, 4 Cyl 2.0 L GAS
View related parts
Chevrolet Equinox Brake Pads Part Number: 42790921
$97.14 MSRP: $175.82
You Save: $78.68 (45%)
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Front Pads
- Replaces: 84685662, 84793349
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2020 Chevrolet Equinox | LT, Premier | 4 Cyl 1.5 L GAS, 4 Cyl 2.0 L GAS
View related parts
Chevrolet Equinox Brake Pads, Front Part Number: 21990460
$70.68 MSRP: $126.23
You Save: $55.55 (45%)
Product Specifications
- Other Name: Pad Kit, Front Disc Brake; Disc Brake Hardware Kit; Disc Brake Pad Set; Front Pads; Pads; Pad Kit, Brake
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2007 Chevrolet Equinox | LS, LT | 6 Cyl 3.4 L GAS

Chevrolet Equinox Brake Pad

Want to cut long-term maintenance and repair costs? Choose OEM Brake Pad. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Equinox parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Equinox Brake Pad includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

Chevrolet Equinox Brake Pad are part of mechanical system in the automobile whose primary function is to apply breaking friction that is in the form of a rotating brake rotor to slow down the car through energy transformation from the kinetic type to thermal type. These pads are usually made of metals and synthetic materials to endure high temperatures with a view of offering good brake force. Equinox Brake Pads are those which have steel backing plates on which there is friction material that gets transferred to the rotor for making the required friction for braking. It is necessary to service and replace these pads often, though the wear indicators are designed to notify the drivers of when to replace the pads. Brake pad can be Non-Metallic, Semi-Metallic, Metallic or Ceramic depending on a variety of requirements of friction, rate of wear, and operating noise. Choosing the appropriate Chevrolet Equinox Brake Pad type and its maintenance significantly affects braking performance and the part's durability.

Chevrolet Equinox Brake Pad Parts and Q&A

Brake Pads
23214903
Q: How to replace the rear disc brake pads on Chevrolet Equinox?
A:
Check the brake fluid level in the master cylinder reservoir before work. Remove brake fluid when the fluid is above midfield but below the highest and lowest acceptable mark. Position the vehicle on jack stands before you take out the tire and wheel unit. Use hand tools to take out the lower bolt of the brake caliper guide pin. Hold the guide pin with an open-end wrench but keep the brake caliper safe from contact to prevent brake pulsation during use. Set the brake caliper upward and place a solid wood block onto the brake pistons. Press all brake piston both clearly into its housing using the Brake Pad spreader tool or a similar tool. Take all Brake Pad components from the set including both pads and their springs but remove and discard only the old springs when replacing with new brake pads. Put new springs over both Brake Pad spots then place in inner and outer Brake Pad positions. Secure the brake caliper guide pin bolt at 27 nm (20 lb ft) while positioning the brake caliper into its installed setup. Turn off your engine and fit back the tire-wheel assembly. Press the brake pedal incrementally until it reaches 2/3 of its length and let go. Do this until the Brake Caliper Piston and pad correctly align inside the brake system. Refill the master cylinder reservoir and let the brake pads and rotors run-in.
Brake Pads
20801538
Q: How to replace the front disc brake pads on Chevrolet Equinox?
A:
First thing that you should do in order to replace the front disc brake pads should be the inspection of the fluid level in the brake master cylinder reservoir; if it is at the midway point between maximum-full point and minimum allowable level watere is not required to be drained but if it is high, drain out to the midway point. Lift the vehicle and remove the tire and wheel assembly. Push a large c-clamp over the brake caliper body against the brake caliper outer Brake Pad and compress the Brake Caliper Piston completely into the brake caliper bore with a c-clamp. Prevent using air tools for the guide pin bolts; instead use hand tools and an open end wrench to hold the caliper guide pin lined when removing the lower brake caliper guide pin bolt. Lift the brake caliper towards you and locate the Brake Pad wear sensor, in order to install correctly, and remove the inner Brake Pad and outer Brake Pad and the upper and lower Brake Pad springs. In case of replacing brake pads, dispose of the old springs; insert, the inner Brake Pad and outer Brake Pad, and return the brake caliper back into the desired position. While holding the brake caliper, the pin of the guide with the help of a back up wrench, tighten the lower brake caliper guide pin bolt to 27 nm (20 lb ft). Reinstall the tire and wheel assembly, gradually press down the Brake Pedal to about 2/3rd of its travel distance with the engine off, then slowly release it until you work up through this cycle until afirm Brake Pedal is achieved to seat the Brake Caliper Piston and brake pads properly. Lastly, top up the master cylinder tank and burnish the brake pads and rotors.