How to Properly Service and Repair the Drive Shaft on GMC Sierra 1500?

A valid replacement of the front propeller shaft begins by raising the vehicle while using a flat-bladed tool to extract the clamp at the Transfer Case. Note the proper position of the propeller shaft relative to the front axle pinion yoke before avoiding hammering on the yoke ears or inserting tools into the space between the yoke and Universal Joint since this could fracture the injection joints. Disassemble the front axle pinion yoke by removing its bolts and yoke retainers but protect the bearing cap assemblies from falling off. Support the propeller shaft through front axle pinion yoke removal by applying tape to bearing caps to minimize loss of bearing rollers. Pull the boot off from the Transfer Case output shaft groove before sliding the propeller shaft forward to separate it from the output shaft. The installation process demands inspectors check the output shaft splines for adequate lubrication before applying gm p/n 12345879 (Canadian P/N 10953511) grease or equivalent with gm specification 9985830. The propeller shaft boot should be installed along with its clamping device before sliding the propeller shaft splines into the Transfer Case output shaft. Connect the propeller shaft to the front axle pinion yoke by aligning the reference marks that were used during the removal process. Install yoke retainers with bolts while securing the yoke retainer bolts at 25 nm (18 lb ft). Use the j 43218 to clamp both boot sides after fitting the boot around the Transfer Case output shaft. Then lower the vehicle.

How to properly remove and install a Drive Shaft on GMC Acadia?

The initial step requires marking the transfer case flange to the propeller shaft flange and the rear differential drive flange to minimize driveline system imbalance. This marking process should include painting or scribing these parts. Raise and support the vehicle. Record the positioning relationship between the front propeller shaft and the transfer case drive flange as well as the propeller shaft positioning with the rear differential yoke. First remove the mounting bolts and the propeller shaft bolts from the rear differential drive flange. Then support the propeller shaft at its rear differential position. Disassemble the propeller shaft bolts along with its associated washers from the system. A brass drift or punch should be placed on the propeller shaft where it meets between notches of the transfer case drive flange then a hammer can be used against the drift or punch to separate the propeller drive shaft from both transfer case and rear differential drive flange. Hold up the propeller shaft at the transfer case drive flange then loosen its center support mounting bolts. An assistant helps while you extract the propeller shaft both from the vehicle supports and vehicle itself. The installation process requires alignment of paint marks on the transfer case flange to propeller shaft flange and the rear differential drive flange for minimized driveline system imbalance. Apply threadlocker to the bolt threads after cleaning mounting bolts from the center bearing as well as front and rear propeller shaft drive flanges. First install several propeller shaft mounting bolts together with washers while support personnel maintain its position on both mounts. Drive the transfer case flange reference points to match those on the front propeller shaft before fastening the mounting bolt that centers the bearing. Placing the center support bearing onto the vehicle now allows you to install a few mounting bolts which will maintain the position of the propeller shaft. Locate the reference points of the rear propeller shaft based on the rear differential yoke. Secure the propeller shaft bolts with washers on the transfer case flange by tightening them to 34 Nm (25 lb ft). Position the center support bearing on the vehicle then install several mounting bolts onto the propeller shaft - rear differential yoke connection while tightening to 58 Nm (43 lb ft). Proceed by taking away the vehicle supports before lowering the vehicle to the floor.

OEM GMC Drive Shaft

Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

359 Drive Shafts found

View related parts
GMC Drive Shaft Part Number: 23251126
$1318.71 MSRP: $3298.47
You Save: $1979.76 (61%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 22760943
Fits the following GMC Models:
- Sierra 1500 | 2014-2018 | Base, SLE | 6 Cyl 4.3 L FLEX
View related parts
GMC Drive Shaft Assembly Part Number: 23242262
$503.86 MSRP: $1248.64
You Save: $744.78 (60%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
Fits the following GMC Models:
- Sierra 1500 | 2014-2018 | Base, Denali, SLE, SLT | 6 Cyl 4.3 L FLEX, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.3 L MILD HYBRID EV-GAS (MHEV), 8 Cyl 6.2 L GAS
View related parts
GMC Drive Shaft Part Number: 23508419
$1301.53 MSRP: $2878.34
You Save: $1576.81 (55%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Front & Rear Propeller; Driveshaft; Shaft, Propeller
- Replaces: 22760962, 23184397, 23251179, 23423781
Fits the following GMC Models:
- Sierra 1500 | 2014-2018 | Base, Denali, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.3 L MILD HYBRID EV-GAS (MHEV)
View related parts
GMC Drive Shaft, Front Part Number: 22760960
$389.77 MSRP: $713.61
You Save: $323.84 (46%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Front Axle Propeller; Driveshaft; Drive Shaft Assembly; Shaft, Propeller
- Position: Front
Fits the following GMC Models:
- Sierra 1500 | 2014-2018 | Base, Denali, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.3 L MILD HYBRID EV-GAS (MHEV), 8 Cyl 6.2 L GAS
- Sierra 1500 Limited | 2019 | Base, SLE | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
- Yukon | 2015-2020 | Denali, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
- Yukon XL | 2015-2020 | Denali, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View More
View related parts
GMC Drive Shaft Part Number: 84202532
$430.46 MSRP: $751.14
You Save: $320.68 (43%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Drive Shaft Assembly; Shaft, Propeller
- Replaces: 23147488, 23209520, 23251155
Fits the following GMC Models:
- Yukon XL | 2015-2020 | Denali, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
GMC Drive Shaft Part Number: 84369125
$449.91 MSRP: $741.14
You Save: $291.23 (40%)
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 84059646, 94769073
Fits the following GMC Models:
- Canyon | 2015-2022 | AT4, All Terrain, Base, Denali, Elevation, Elevation Standard, SL, SLE, SLT | 4 Cyl 2.5 L GAS, 4 Cyl 2.8 L DIESEL, 6 Cyl 3.6 L GAS
View related parts
GMC Drive Shaft Part Number: 25995545
$1393.09 MSRP: $1812.50
You Save: $419.41 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
Fits the following GMC Models:
- Acadia | 2007-2011 | Denali, SL, SLE, SLT | 6 Cyl 3.6 L GAS
View related parts
GMC Drive Shaft Part Number: 20912697
$1246.89 MSRP: $1612.02
You Save: $365.13 (23%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 15794277
Fits the following GMC Models:
- Sierra 1500 | 2007-2013 | Denali, Hybrid, SL, SLE, SLT, WT, XFE | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
GMC Drive Shaft Assembly Part Number: 23418974
$569.27 MSRP: $899.77
You Save: $330.50 (37%)
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 23318715, 23497604, 23126606
Fits the following GMC Models:
- Sierra 1500 | 2014-2018 | Base, Denali, SLE, SLT | 6 Cyl 4.3 L FLEX, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.3 L MILD HYBRID EV-GAS (MHEV), 8 Cyl 6.2 L GAS
View related parts
GMC Drive Shaft, Front Part Number: 25843685
$598.49 MSRP: $945.95
You Save: $347.46 (37%)
Product Specifications
- Other Name: Shaft Assembly-Front Axle Propeller; Driveshaft; Shaft, Propeller
- Position: Front
- Replaces: 15104642
Fits the following GMC Models:
- Canyon | 2004-2012 | SL, SLE, SLT, WT, Z71 Fleet, Z71 SL, Z71 SLE, Z85 SL, Z85 SLE | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS
View related parts
GMC Drive Shaft, Front Part Number: 25833035
Product Specifications
- Other Name: Shaft Assembly-Front Axle Propeller; Driveshaft; Shaft, Propeller
- Position: Front
Fits the following GMC Models:
- Envoy | 2008 | Denali | 8 Cyl 5.3 L GAS
View related parts
GMC Drive Shaft Part Number: 25787946
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
Fits the following GMC Models:
- Canyon | 2004-2007 | SL, SLE, SLT, WT, Z71 Fleet, Z71 SL, Z71 SLE, Z85 SL, Z85 SLE | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS
View related parts
GMC Drive Shaft, Front Part Number: 15186002
Product Specifications
- Other Name: Shaft, Front Axle Propeller; Driveshaft; Shaft, Propeller
- Position: Front
Fits the following GMC Models:
- Sierra 1500 Classic | 2007 | Hybrid | 8 Cyl 5.3 L FULL HYBRID EV-GAS (FHEV)
View related parts
GMC Drive Shaft Part Number: 15286715
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Drive Shaft Assembly; Shaft, Propeller
Fits the following GMC Models:
- Canyon | 2004-2012 | SL, SLE, SLT, WT, Z71 Fleet, Z71 SL, Z71 SLE, Z85 SL, Z85 SLE | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS
View related parts
GMC Drive Shaft Part Number: 25787947
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 15116624
Fits the following GMC Models:
- Canyon | 2004-2012 | SL, SLE, SLT, WT, Z71 Fleet, Z71 SL, Z71 SLE, Z85 SL, Z85 SLE | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS
View related parts
GMC Drive Shaft, Front Part Number: 22845694
Product Specifications
- Other Name: Shaft Assembly-Front Axle Propeller; Driveshaft; Shaft, Propeller
- Position: Front
- Replaces: 15902927
Fits the following GMC Models:
- Sierra 1500 | 2008-2013 | Denali, Hybrid, SL, SLE, SLT, WT, XFE | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
- Yukon | 2007-2014 | Denali, Denali Hybrid, Hybrid, SLE, SLT | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
- Yukon XL 1500 | 2007-2014 | Denali, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
- Yukon XL 2500 | 2007-2013 | SLE, SLT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS
View More
View related parts
GMC Drive Shaft Assembly Part Number: 15109397
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 15713680
Fits the following GMC Models:
- Yukon XL 1500 | 2000-2006 | Denali, SL, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
- Yukon XL 2500 | 2000-2006 | SLE, SLT | 8 Cyl 6.0 L GAS, 8 Cyl 8.1 L GAS
View related parts
GMC Drive Shaft Part Number: 20912699
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 15855534
Fits the following GMC Models:
- Sierra 1500 | 2007-2013 | Denali, SLE, SLT | 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
GMC Drive Shaft Assembly Part Number: 25776416
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
Fits the following GMC Models:
- Sierra 2500 HD | 2007-2010 | SLE, SLT, WT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
- Sierra 3500 HD | 2007-2010 | SLE, SLT, WT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
View related parts
GMC Drive Shaft Part Number: 15814472
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
Fits the following GMC Models:
- Yukon | 2007-2008 | Denali, SLE, SLT | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS

| Page 1 of 18 |Next >

1-20 of 359 Results

GMC Drive Shaft

Choose OEM Drive Shaft, you're making the optimal decision for superior quality and perfect performance. You can feel confident because each component goes through stringent quality checks. Every part is carefully built to comply with GMC's factory specifications. You'll enjoy a smooth, worry-free installation that fits just right. At ChevyPartsDeal.com, you'll find it easy to get top-quality OEM GMC Drive Shaft. You can shop at highly competitive prices and protect your budget. All our genuine GMC parts include a dependable manufacturer's warranty. You'll also appreciate our straightforward return policy and swift delivery services for extra convenience.

GMC Drive Shaft transmits the torque of the engine to all the axles in a smooth manner that makes the trucks pull without any drama. GMC began back in 1901 with the construction of sturdy workhorses in farms and quarries and that maker mindset continues to dominate every truck and SUV that is put out there today. The boxed steel frames shake off potholes, towing strains, and gravel ruts and the cabins remain silent with the help of thick glass and closed seals. The use of surround vision cameras, hitch guidance lines, and lane alert systems leaves the driver with a fixed focus on the task instead of multi-tasking with blind spots. Multi-mode tailgates and smartly damped suspensions are also bolted in by GMC to make running weekend errands as easy as running weekday payloads. Incessant proving-ground testing supports that belief, and the owners are able to trust the rig and the job will be done without worrying about it. Drive Shaft choices include one-piece tubes to allow simple rear-wheel applications, slip-in tube assemblies that can be adjusted in length on-the-fly, and multi-segment shafts that align with the transfer cases in four-wheel or all-wheel drive designs by adding either a universal or splined joint to maintain angles happy during suspension travel. Vibration is reduced by a balanced Drive Shaft which transmits the engine rotation to the differential and maintains bearing life even with the throttle held open. The Drive Shaft is made with steel or aluminum tubing selected based on the balance of strength and weight and its serviceable joints allow the angle adjustments to occur without being bound when going off-camber in trails or tight parking tasks.

GMC Drive Shaft Parts and Q&A

Drive Shaft
20912697
Q: How to Properly Service and Repair the Drive Shaft on GMC Sierra 1500?
A:
A valid replacement of the front propeller shaft begins by raising the vehicle while using a flat-bladed tool to extract the clamp at the Transfer Case. Note the proper position of the propeller shaft relative to the front axle pinion yoke before avoiding hammering on the yoke ears or inserting tools into the space between the yoke and Universal Joint since this could fracture the injection joints. Disassemble the front axle pinion yoke by removing its bolts and yoke retainers but protect the bearing cap assemblies from falling off. Support the propeller shaft through front axle pinion yoke removal by applying tape to bearing caps to minimize loss of bearing rollers. Pull the boot off from the Transfer Case output shaft groove before sliding the propeller shaft forward to separate it from the output shaft. The installation process demands inspectors check the output shaft splines for adequate lubrication before applying gm p/n 12345879 (Canadian P/N 10953511) grease or equivalent with gm specification 9985830. The propeller shaft boot should be installed along with its clamping device before sliding the propeller shaft splines into the Transfer Case output shaft. Connect the propeller shaft to the front axle pinion yoke by aligning the reference marks that were used during the removal process. Install yoke retainers with bolts while securing the yoke retainer bolts at 25 nm (18 lb ft). Use the j 43218 to clamp both boot sides after fitting the boot around the Transfer Case output shaft. Then lower the vehicle.
Drive Shaft
25995545
Q: How to properly remove and install a Drive Shaft on GMC Acadia?
A:
The initial step requires marking the transfer case flange to the propeller shaft flange and the rear differential drive flange to minimize driveline system imbalance. This marking process should include painting or scribing these parts. Raise and support the vehicle. Record the positioning relationship between the front propeller shaft and the transfer case drive flange as well as the propeller shaft positioning with the rear differential yoke. First remove the mounting bolts and the propeller shaft bolts from the rear differential drive flange. Then support the propeller shaft at its rear differential position. Disassemble the propeller shaft bolts along with its associated washers from the system. A brass drift or punch should be placed on the propeller shaft where it meets between notches of the transfer case drive flange then a hammer can be used against the drift or punch to separate the propeller drive shaft from both transfer case and rear differential drive flange. Hold up the propeller shaft at the transfer case drive flange then loosen its center support mounting bolts. An assistant helps while you extract the propeller shaft both from the vehicle supports and vehicle itself. The installation process requires alignment of paint marks on the transfer case flange to propeller shaft flange and the rear differential drive flange for minimized driveline system imbalance. Apply threadlocker to the bolt threads after cleaning mounting bolts from the center bearing as well as front and rear propeller shaft drive flanges. First install several propeller shaft mounting bolts together with washers while support personnel maintain its position on both mounts. Drive the transfer case flange reference points to match those on the front propeller shaft before fastening the mounting bolt that centers the bearing. Placing the center support bearing onto the vehicle now allows you to install a few mounting bolts which will maintain the position of the propeller shaft. Locate the reference points of the rear propeller shaft based on the rear differential yoke. Secure the propeller shaft bolts with washers on the transfer case flange by tightening them to 34 Nm (25 lb ft). Position the center support bearing on the vehicle then install several mounting bolts onto the propeller shaft - rear differential yoke connection while tightening to 58 Nm (43 lb ft). Proceed by taking away the vehicle supports before lowering the vehicle to the floor.