How to Properly Service and Repair the Drive Shaft on GMC Sierra 1500?

A valid replacement of the front propeller shaft begins by raising the vehicle while using a flat-bladed tool to extract the clamp at the Transfer Case. Note the proper position of the propeller shaft relative to the front axle pinion yoke before avoiding hammering on the yoke ears or inserting tools into the space between the yoke and Universal Joint since this could fracture the injection joints. Disassemble the front axle pinion yoke by removing its bolts and yoke retainers but protect the bearing cap assemblies from falling off. Support the propeller shaft through front axle pinion yoke removal by applying tape to bearing caps to minimize loss of bearing rollers. Pull the boot off from the Transfer Case output shaft groove before sliding the propeller shaft forward to separate it from the output shaft. The installation process demands inspectors check the output shaft splines for adequate lubrication before applying gm p/n 12345879 (Canadian P/N 10953511) grease or equivalent with gm specification 9985830. The propeller shaft boot should be installed along with its clamping device before sliding the propeller shaft splines into the Transfer Case output shaft. Connect the propeller shaft to the front axle pinion yoke by aligning the reference marks that were used during the removal process. Install yoke retainers with bolts while securing the yoke retainer bolts at 25 nm (18 lb ft). Use the j 43218 to clamp both boot sides after fitting the boot around the Transfer Case output shaft. Then lower the vehicle.

How to replace the front drive shaft on GMC Sierra 1500?

Raising the car requires the first step before removing the clamp positioned at the Transfer Case through prying up this part with a flat-bladed tool. The propeller shaft's relationship with the front axle pinion yoke requires marking before applying force in any way on the yoke ears or utilizing tools between the components since this could break the universal joints of the injection points. Gently remove all bolts and retainers from the front axle pinion yoke while avoiding the loss of bearing cap assemblies. After disconnecting the propeller shaft from its front axle pinion yoke position you should blind tape the bearing caps to avoid socket bearing loss. The output shaft of the Transfer Case requires boot removal from its groove so the propeller shaft can be advanced forward for separation. The Transfer Case output shaft splines need to be inspected for proper lubrication before applying grease gm p/n 12345879 (Canadian P/N 10953511) or an equivalent material following gm specification 9985830. The boot must be installed followed by the boot clamp on the propeller shaft before inserting the splines of the shaft into the Transfer Case output shaft. Synchronize the propeller shaft reference marks made at removal time when reconnecting it to the front axle pinion yoke. Insert yoke retainers and fasten the retaining bolts based on 25 nm (18 lb ft). To complete the installation process lower the vehicle then use j 43218 tool to crimp both clamps onto the Transfer Case output shaft boot.

OEM GMC Sierra 1500 Drive Shaft

Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

73 Drive Shafts found

View related parts
GMC Sierra 1500 Drive Shaft Part Number: 23251126
$1286.54 MSRP: $3218.01
You Save: $1931.47 (61%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 22760943
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2018 GMC Sierra 1500 | Base, SLE | 6 Cyl 4.3 L FLEX
View related parts
GMC Sierra 1500 Drive Shaft Assembly Part Number: 23242262
$503.86 MSRP: $1248.64
You Save: $744.78 (60%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2018 GMC Sierra 1500 | Base, Denali, SLE, SLT | 6 Cyl 4.3 L FLEX, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.3 L MILD HYBRID EV-GAS (MHEV), 8 Cyl 6.2 L GAS
View related parts
GMC Sierra 1500 Drive Shaft Part Number: 23508419
$1301.53 MSRP: $2878.34
You Save: $1576.81 (55%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Front & Rear Propeller; Driveshaft; Shaft, Propeller
- Position: Front and Rear
- Replaces: 23251179, 22760962, 23423781, 23184397
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2018 GMC Sierra 1500 | Base, Denali, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.3 L MILD HYBRID EV-GAS (MHEV)
View related parts
GMC Sierra 1500 Drive Shaft, Front Part Number: 22760960
$394.54 MSRP: $696.20
You Save: $301.66 (44%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Front Axle Propeller; Driveshaft; Drive Shaft Assembly; Shaft, Propeller
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2019 GMC Sierra 1500 | AT4, Base, Denali, Elevation, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.3 L MILD HYBRID EV-GAS (MHEV), 8 Cyl 6.2 L GAS
View related parts
GMC Sierra 1500 Drive Shaft, Front Part Number: 84669663
$299.24 MSRP: $624.71
You Save: $325.47 (53%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Front Axle Propeller; Driveshaft; Shaft, Propeller
- Position: Front
- Replaces: 15182098, 84060396, 15090195, 15719954
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007 GMC Sierra 1500 | Denali, SL, SLE, SLT, WT | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L GAS
View related parts
GMC Sierra 1500 Drive Shaft, Front Part Number: 22760959
$328.93 MSRP: $579.32
You Save: $250.39 (44%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Front Axle Propeller; Driveshaft; Drive Shaft Assembly; Shaft, Propeller
- Position: Front
- Replaces: 23180816
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2018 GMC Sierra 1500 | Base, Denali, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.3 L MILD HYBRID EV-GAS (MHEV), 8 Cyl 6.2 L GAS
View related parts
GMC Sierra 1500 Drive Shaft Part Number: 23508418
$1145.68 MSRP: $1946.60
You Save: $800.92 (42%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Front & Rear Propeller; Driveshaft; Shaft, Propeller
- Position: Front and Rear
- Replaces: 22760961, 23423780, 23184396, 23251178
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2018 GMC Sierra 1500 | Base, SLE | 6 Cyl 4.3 L FLEX
View related parts
GMC Sierra 1500 Drive Shaft Part Number: 84907477
$455.14 MSRP: $722.44
You Save: $267.30 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 23370110
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2019-2023 GMC Sierra 1500 | Base, Denali, Elevation, Pro, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
View related parts
GMC Sierra 1500 Drive Shaft Part Number: 84202536
$442.07 MSRP: $752.61
You Save: $310.54 (42%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 23147494, 23251161
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2018 GMC Sierra 1500 | Base, SLE | 6 Cyl 4.3 L FLEX
View related parts
GMC Sierra 1500 Drive Shaft Part Number: 84907480
$558.18 MSRP: $886.03
You Save: $327.85 (37%)
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaced by: 85731728
- Replaces: 23370117
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2019-2023 GMC Sierra 1500 | Base, Elevation, Pro, SLE | 4 Cyl 2.7 L GAS
View related parts
GMC Sierra 1500 Axle Assembly, Front Part Number: 84557636
$1327.80 MSRP: $2098.64
You Save: $770.84 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Axle Assembly-Front; Differential; Axle Shaft; Differential Assembly
- Position: Front
- Replaces: 84514361, 84439895
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2019-2020 GMC Sierra 1500 | AT4, Base, Denali, Elevation, SLE, SLT | 4 Cyl 2.7 L GAS, 6 Cyl 3.0 L DIESEL, 6 Cyl 4.3 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
View related parts
GMC Sierra 1500 Drive Shaft Part Number: 84907481
$516.87 MSRP: $820.46
You Save: $303.59 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 23370118
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2019-2021 GMC Sierra 1500 | Base | 6 Cyl 4.3 L GAS
View related parts
GMC Sierra 1500 Drive Shaft Part Number: 84500380
$597.30 MSRP: $943.84
You Save: $346.54 (37%)
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2019-2023 GMC Sierra 1500 | Base, Elevation, Pro, SLE | 4 Cyl 2.7 L GAS
View related parts
GMC Sierra 1500 Drive Shaft Part Number: 84907483
$417.83 MSRP: $663.39
You Save: $245.56 (38%)
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaced by: 85731732
- Replaces: 23370120
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2019-2023 GMC Sierra 1500 | AT4, AT4X, Base, Denali, Denali Ultimate, Elevation, Pro, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
View related parts
GMC Sierra 1500 Drive Shaft Part Number: 23370108
$371.65 MSRP: $612.09
You Save: $240.44 (40%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaced by: 84907475
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2019-2023 GMC Sierra 1500 | Base, Denali, Elevation, Pro, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
View related parts
GMC Sierra 1500 Drive Shaft Part Number: 84907484
$367.59 MSRP: $583.62
You Save: $216.03 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 23370121
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2019-2023 GMC Sierra 1500 | AT4, Base, Denali, Elevation, Pro, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
View related parts
GMC Sierra 1500 Drive Shaft Part Number: 84539693
$558.97 MSRP: $883.29
You Save: $324.32 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Front & Rear Propeller; Shaft, Propeller
- Position: Front and Rear
- Replaces: 23370097
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2019-2023 GMC Sierra 1500 | AT4, Base, Denali, Elevation, Pro, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
View related parts
GMC Sierra 1500 Drive Shaft Part Number: 23370122
$329.19 MSRP: $517.86
You Save: $188.67 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2019-2021 GMC Sierra 1500 | Base | 6 Cyl 4.3 L GAS
View related parts
GMC Sierra 1500 Drive Shaft, Front Part Number: 23370091
$249.38 MSRP: $392.38
You Save: $143.00 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Front Axle Propeller; Driveshaft; Shaft, Propeller
- Position: Front
- Replaced by: 85519800
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2019-2021 GMC Sierra 1500 | Base | 6 Cyl 4.3 L GAS
View related parts
GMC Sierra 1500 Drive Shaft Part Number: 23242263
$494.28 MSRP: $1239.67
You Save: $745.39 (61%)
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 23147491
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2018 GMC Sierra 1500 | Base, Denali, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.3 L MILD HYBRID EV-GAS (MHEV)

| Page 1 of 4 |Next >

1-20 of 73 Results

GMC Sierra 1500 Drive Shaft

Want to cut long-term maintenance and repair costs? Choose OEM Drive Shaft. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine GMC Sierra 1500 parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM GMC Sierra 1500 Drive Shaft includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

GMC Sierra 1500 Drive Shaft Parts and Q&A

Drive Shaft
20912697
Q: How to Properly Service and Repair the Drive Shaft on GMC Sierra 1500?
A:
A valid replacement of the front propeller shaft begins by raising the vehicle while using a flat-bladed tool to extract the clamp at the Transfer Case. Note the proper position of the propeller shaft relative to the front axle pinion yoke before avoiding hammering on the yoke ears or inserting tools into the space between the yoke and Universal Joint since this could fracture the injection joints. Disassemble the front axle pinion yoke by removing its bolts and yoke retainers but protect the bearing cap assemblies from falling off. Support the propeller shaft through front axle pinion yoke removal by applying tape to bearing caps to minimize loss of bearing rollers. Pull the boot off from the Transfer Case output shaft groove before sliding the propeller shaft forward to separate it from the output shaft. The installation process demands inspectors check the output shaft splines for adequate lubrication before applying gm p/n 12345879 (Canadian P/N 10953511) grease or equivalent with gm specification 9985830. The propeller shaft boot should be installed along with its clamping device before sliding the propeller shaft splines into the Transfer Case output shaft. Connect the propeller shaft to the front axle pinion yoke by aligning the reference marks that were used during the removal process. Install yoke retainers with bolts while securing the yoke retainer bolts at 25 nm (18 lb ft). Use the j 43218 to clamp both boot sides after fitting the boot around the Transfer Case output shaft. Then lower the vehicle.
Drive Shaft
20912702
Q: How to replace the front drive shaft on GMC Sierra 1500?
A:
Raising the car requires the first step before removing the clamp positioned at the Transfer Case through prying up this part with a flat-bladed tool. The propeller shaft's relationship with the front axle pinion yoke requires marking before applying force in any way on the yoke ears or utilizing tools between the components since this could break the Universal Joints of the injection points. Gently remove all bolts and retainers from the front axle pinion yoke while avoiding the loss of bearing cap assemblies. After disconnecting the propeller shaft from its front axle pinion yoke position you should blind tape the bearing caps to avoid socket bearing loss. The output shaft of the Transfer Case requires boot removal from its groove so the propeller shaft can be advanced forward for separation. The Transfer Case output shaft splines need to be inspected for proper lubrication before applying grease gm p/n 12345879 (Canadian P/N 10953511) or an equivalent material following gm specification 9985830. The boot must be installed followed by the boot clamp on the propeller shaft before inserting the splines of the shaft into the Transfer Case output shaft. Synchronize the propeller shaft reference marks made at removal time when reconnecting it to the front axle pinion yoke. Insert yoke retainers and fasten the retaining bolts based on 25 nm (18 lb ft). To complete the installation process lower the vehicle then use j 43218 tool to crimp both clamps onto the Transfer Case output shaft boot.