How to check and maintain the drive shaft on Chevrolet Tracker?

Raise the rear of the vehicle and support it securely on jackstands. Block the front wheels. The transmission should be in Neutral. Crawl under the vehicle and visually inspect the driveshaft. Look for dents and cracks in the tube. If any are found, the drive-shaft must be replaced. Check for oil leakage at the front and rear of the driveshaft. Leakage where the driveshaft enters the transmission indicates a defective rear transmission seal. Leakage where the driveshaft enters the differential indicates a defective pinion seal. While still under the vehicle, have an assistant turn the rear wheel so the driveshaft will rotate. As it does, check for binding, noise and excessive play in the U-joints. The universal joints can also be checked with the driveshaft motionless, by gripping both sides of the joint and attempting to twist it. Any movement at all in the joint is a sign of considerable wear. Lifting up on the shaft will also indicate movement in the universal joints. Check the driveshaft mounting bolts at both ends to make sure they're tight. The above driveshaft checks should be repeated on all driveshafts. In addition check for grease leakage around the sleeve yoke, indicating failure of the yoke seal. Check for leakage where the driveshafts connect to the transfer case. The driveshafts must be lubricated periodically as indicated in the maintenance schedule. Use the grease gun to insert grease into the fitting. The driveshafts are lubricated at the fitting and also at the boot. Also pull back the boot at the rear of the axle and insert grease.

How to remove and install drive shaft on 4WD Chevrolet Trailblazer?

Loosen the right front wheel lug nuts, raise the vehicle, place it securely on jackstands, and remove the right front wheel. Remove the splash shield. Remove the right driveaxle and intermediate shaft bearing housing. Thread a slide hammer adapter into the hole in the end of the intermediate shaft and attach a slide hammer to the adapter. Pull the intermediate shaft out of the differential, taking care not to damage the seal on the opposite side of the oil pan. Ensure the retaining ring is in position on the left end of the intermediate shaft, then insert the intermediate shaft through the oil pan passage and into the differential, being careful not to damage the oil seal. Rotate the shaft as necessary to align its splines with the differential. Install the slide hammer on the shaft and use it to drive the shaft in until its retaining ring locks into place in the differential. The remainder of installation follows the reverse order of the removal steps.

OEM Chevrolet Drive Shaft

Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

457 Drive Shafts found

View related parts
Chevrolet Drive Shaft Part Number: 23251126
$1318.71 MSRP: $3298.47
You Save: $1979.76 (61%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 22760943
Fits the following Chevrolet Models:
- Silverado 1500 | 2014-2018 | Custom, LS, LT, WT | 6 Cyl 4.3 L FLEX
View related parts
Chevrolet Drive Shaft Assembly Part Number: 23242262
$503.86 MSRP: $1248.64
You Save: $744.78 (60%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
Fits the following Chevrolet Models:
- Silverado 1500 | 2014-2018 | Custom, High Country, LS, LT, LTZ, SSV, WT | 6 Cyl 4.3 L FLEX, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.3 L MILD HYBRID EV-GAS (MHEV), 8 Cyl 6.2 L GAS
View related parts
Chevrolet Drive Shaft Part Number: 23508419
$1301.53 MSRP: $2878.34
You Save: $1576.81 (55%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Front & Rear Propeller; Driveshaft; Shaft, Propeller
- Replaces: 22760962, 23184397, 23251179, 23423781
Fits the following Chevrolet Models:
- Silverado 1500 | 2014-2018 | Custom, High Country, LS, LT, LTZ, SSV, WT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.3 L MILD HYBRID EV-GAS (MHEV)
View related parts
Chevrolet Axle Assembly, Front Passenger Side Part Number: 19316533
$385.35 MSRP: $723.66
You Save: $338.31 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly, Front Wheel Drive Half; Axle Shaft
- Position: Passenger Side
- Replaced by: 19317950
Fits the following Chevrolet Models:
- City Express | 2015-2018 | LS, LT | 4 Cyl 2.0 L GAS
View related parts
Chevrolet Drive Shaft, Front Part Number: 22760960
$389.77 MSRP: $713.61
You Save: $323.84 (46%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Front Axle Propeller; Driveshaft; Drive Shaft Assembly; Shaft, Propeller
- Position: Front
Fits the following Chevrolet Models:
- Silverado 1500 | 2014-2018 | Custom, High Country, LS, LT, LTZ, SSV, WT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.3 L MILD HYBRID EV-GAS (MHEV), 8 Cyl 6.2 L GAS
- Silverado 1500 LD | 2019 | Custom, LT, WT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
- Suburban | 2015-2020 | LS, LT, LTZ, Premier | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
- Tahoe | 2015-2020 | LS, LT, LTZ, PPV, Premier, SSV | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View More
View related parts
Chevrolet Drive Shaft Part Number: 84202532
$441.21 MSRP: $751.14
You Save: $309.93 (42%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Drive Shaft Assembly; Shaft, Propeller
- Replaces: 23147488, 23209520, 23251155
Fits the following Chevrolet Models:
- Suburban | 2015-2020 | LS, LT, LTZ, Premier | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Drive Shaft Part Number: 84369125
$449.91 MSRP: $741.14
You Save: $291.23 (40%)
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 84059646, 94769073
Fits the following Chevrolet Models:
- Colorado | 2015-2022 | Base, LT, WT, Z71, ZR2 | 4 Cyl 2.5 L GAS, 4 Cyl 2.8 L DIESEL, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Drive Shaft Part Number: 23357418
$1789.35 MSRP: $2814.86
You Save: $1025.51 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Support Assembly-Driveline; Driveshaft; Drive Shaft Assembly
- Replaced by: 84016823
Fits the following Chevrolet Models:
- Corvette | 2015-2019 | Grand Sport, Stingray, ZR1 | 8 Cyl 6.2 L GAS
View related parts
Chevrolet Drive Shaft Part Number: 25995545
$1393.09 MSRP: $1812.50
You Save: $419.41 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
Fits the following Chevrolet Models:
- Traverse | 2009-2011 | LS, LT, LTZ | 6 Cyl 3.6 L GAS
View related parts
Chevrolet Drive Shaft Part Number: 20912697
$1246.89 MSRP: $1612.02
You Save: $365.13 (23%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 15794277
Fits the following Chevrolet Models:
- Silverado 1500 | 2007-2013 | Hybrid, LS, LT, LTZ, WT, XFE | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX
View related parts
Chevrolet Drive Shaft Assembly Part Number: 23418974
$569.27 MSRP: $899.77
You Save: $330.50 (37%)
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 23318715, 23497604, 23126606
Fits the following Chevrolet Models:
- Silverado 1500 | 2014-2018 | Custom, High Country, LS, LT, LTZ, SSV, WT | 6 Cyl 4.3 L FLEX, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.3 L MILD HYBRID EV-GAS (MHEV), 8 Cyl 6.2 L GAS
View related parts
Chevrolet Drive Shaft, Front Part Number: 25843685
$598.49 MSRP: $945.95
You Save: $347.46 (37%)
Product Specifications
- Other Name: Shaft Assembly-Front Axle Propeller; Driveshaft; Shaft, Propeller
- Position: Front
- Replaces: 15104642
Fits the following Chevrolet Models:
- Colorado | 2004-2012 | Base, LS, LT, Sport, Sport LS, WT, Z71, Z71 LS, Z85, Z85 LS | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Drive Shaft, Front Part Number: 25833035
Product Specifications
- Other Name: Shaft Assembly-Front Axle Propeller; Driveshaft; Shaft, Propeller
- Position: Front
Fits the following Chevrolet Models:
- Trailblazer | 2008 | Base, LT | 8 Cyl 5.3 L GAS
View related parts
Chevrolet Drive Shaft Part Number: 25787946
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
Fits the following Chevrolet Models:
- Colorado | 2004-2007 | Base, LS, LT, Sport LS, WT, Z71, Z71 LS, Z85, Z85 LS | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS
View related parts
Chevrolet Drive Shaft Part Number: 15286715
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Drive Shaft Assembly; Shaft, Propeller
Fits the following Chevrolet Models:
- Colorado | 2004-2012 | Base, LS, LT, Sport, Sport LS, WT, Z71, Z71 LS, Z85, Z85 LS | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Drive Shaft Part Number: 20931145
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft
- Replaced by: 25636880
Fits the following Chevrolet Models:
- Camaro | 2012-2015 | Z/28, ZL1 | 8 Cyl 6.2 L GAS, 8 Cyl 7.0 L GAS
View related parts
Chevrolet Drive Shaft, Front Part Number: 30012976
Product Specifications
- Other Name: Shaft Assembly, Propeller Front (On Esn); Shaft, Propeller
- Position: Front
Fits the following Chevrolet Models:
- Tracker | 1998-2003 | Base, LSi, LT, ZR2 | 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L GAS
View related parts
Chevrolet Drive Shaft Part Number: 25787947
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 15116624
Fits the following Chevrolet Models:
- Colorado | 2004-2012 | Base, LS, LT, Sport LS, WT, Z71, Z71 LS, Z85, Z85 LS | 4 Cyl 2.8 L GAS, 4 Cyl 2.9 L GAS, 5 Cyl 3.5 L GAS, 5 Cyl 3.7 L GAS
View related parts
Chevrolet Drive Shaft, Front Part Number: 22845694
Product Specifications
- Other Name: Shaft Assembly-Front Axle Propeller; Driveshaft; Shaft, Propeller
- Position: Front
- Replaces: 15902927
Fits the following Chevrolet Models:
- Avalanche | 2007-2013 | Black Diamond LS, Black Diamond LT, Black Diamond LTZ, LS, LT, LTZ | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
- Silverado 1500 | 2008-2013 | Hybrid, LS, LT, LTZ, WT, XFE | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX
- Suburban 1500 | 2007-2014 | LS, LT, LTZ | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
- Suburban 2500 | 2007-2013 | LS, LT, LTZ | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS
- Tahoe | 2007-2014 | Hybrid, LS, LT, LTZ, SSV | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View More
View related parts
Chevrolet Drive Shaft Assembly Part Number: 15109397
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 15713680
Fits the following Chevrolet Models:
- Suburban 1500 | 2000-2006 | Base, LS, LT, LTZ, Z71 | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
- Suburban 2500 | 2000-2006 | Base, LS, LT | 8 Cyl 6.0 L GAS, 8 Cyl 8.1 L GAS

| Page 1 of 23 |Next >

1-20 of 457 Results

Chevrolet Drive Shaft

Choose OEM Drive Shaft, you're making the optimal decision for superior quality and perfect performance. You can feel confident because each component goes through stringent quality checks. Every part is carefully built to comply with Chevrolet's factory specifications. You'll enjoy a smooth, worry-free installation that fits just right. At ChevyPartsDeal.com, you'll find it easy to get top-quality OEM Chevrolet Drive Shaft. You can shop at highly competitive prices and protect your budget. All our genuine Chevrolet parts include a dependable manufacturer's warranty. You'll also appreciate our straightforward return policy and swift delivery services for extra convenience.

Chevrolet Drive Shaft drives the engine power straight to the wheels without shaking under the pressure. Chevrolet was founded in 1911 and it has lived every decade pursuing real speed and new style. Chevy lines are road-trip friendly with powertrains that are affordable to everyday budgets. Multiple entertainment Super Cruise hands-free assistance, loud streaming music, and fast phone connectivity make Chevy fun to any driver. The badge symbolizes simple ownership, simple technology, and the choice to go anywhere in between city hatch to burly hauler. It is continually becoming cleaner with smarter safety features that reduce stress in busy commutes and on the open roads as well. Whether it is a compact or a truck, customers are getting the same thing: no-frills performance. The Drive Shaft is the main component of the powertrain itself; it is a metal rod connected to the output of the transmission and eventually the wheels in any type of rear, front, or all-wheel design. It withstands torsion and shear using one-piece, two-piece, or slip-in tube constructions that cut inertia. Universal, splined, or mouth couplings allow the Drive Shaft to bend around out of step and maintain the power in a smooth manner. Drivers of Chevy experience the dividend of clear take-offs, smooth driving, and less vibrations when on rough roads.

Chevrolet Drive Shaft Parts and Q&A

Drive Shaft
30023524
Q: How to check and maintain the drive shaft on Chevrolet Tracker?
A:
Raise the rear of the vehicle and support it securely on jackstands. Block the front wheels. The transmission should be in Neutral. Crawl under the vehicle and visually inspect the driveshaft. Look for dents and cracks in the tube. If any are found, the drive-shaft must be replaced. Check for oil leakage at the front and rear of the driveshaft. Leakage where the driveshaft enters the transmission indicates a defective rear transmission seal. Leakage where the driveshaft enters the differential indicates a defective pinion seal. While still under the vehicle, have an assistant turn the rear wheel so the driveshaft will rotate. As it does, check for binding, noise and excessive play in the U-joints. The universal joints can also be checked with the driveshaft motionless, by gripping both sides of the joint and attempting to twist it. Any movement at all in the joint is a sign of considerable wear. Lifting up on the shaft will also indicate movement in the universal joints. Check the driveshaft mounting bolts at both ends to make sure they're tight. The above driveshaft checks should be repeated on all driveshafts. In addition check for grease leakage around the sleeve yoke, indicating failure of the yoke seal. Check for leakage where the driveshafts connect to the transfer case. The driveshafts must be lubricated periodically as indicated in the maintenance schedule. Use the grease gun to insert grease into the fitting. The driveshafts are lubricated at the fitting and also at the boot. Also pull back the boot at the rear of the axle and insert grease.
Drive Shaft
15833884
Q: How to remove and install drive shaft on 4WD Chevrolet Trailblazer?
A:
Loosen the right front wheel lug nuts, raise the vehicle, place it securely on jackstands, and remove the right front wheel. Remove the splash shield. Remove the right driveaxle and intermediate shaft bearing housing. Thread a slide hammer adapter into the hole in the end of the intermediate shaft and attach a slide hammer to the adapter. Pull the intermediate shaft out of the differential, taking care not to damage the seal on the opposite side of the oil pan. Ensure the retaining ring is in position on the left end of the intermediate shaft, then insert the intermediate shaft through the oil pan passage and into the differential, being careful not to damage the oil seal. Rotate the shaft as necessary to align its splines with the differential. Install the slide hammer on the shaft and use it to drive the shaft in until its retaining ring locks into place in the differential. The remainder of installation follows the reverse order of the removal steps.