Question 1

How to replace the front drive shaft on Chevrolet Suburban 2500?

Accepted Answer

Use the clamp pliers narrow jaw (J 43218) as well as other necessary tools to replace the front propeller shaft. Establish clear markings on all driveline parts which include propeller shafts and wheel drive shafts and pinion flanges and output shafts. Mark the relationships of these elements before start of disassembly process. A vehicle lift procedure should begin by removing the transfer case shield when present. Use a flat-bladed tool to pry open the exposed end of the clamp at the transfer case before removing it. Start by taking off the bolts alongside the yoke retainers installed on the front axle pinion yoke. Disconnect the propeller shaft properly from its position at the front axle pinion yoke but maintain safe control of the bearing cap assemblies. Glide the propeller shaft forward to take it out from the transfer case output shaft. Use the gm p/n 12345879 (Canadian P/N 10953511) or equivalent lubricant to service the splined area of the transfer case output shaft. The recommended gm specification is 9985830. Fit the new clamp inside the propeller shaft boot groove before sliding the propeller shaft splines through the transfer case output shaft to join it with the front axle pinion yoke keeping reference marks in place from removal. Secure the yoke retainers in place using bolts that require torquing to 25 nm (19 ft. Lbs. Tighten the Clamp Pliers Narrow Jaw (J 43218) to crimp the clamp while it is attached to the transfer case output shaft until it enters into the boot groove. To complete the installation the transfer case shield and lower the vehicle if present.

Question 2

How to replace the rear Drive Shaft on Chevrolet Suburban 2500?

Accepted Answer

Replacing the rear propeller shaft begins with properly referencing driveline components to the propeller shaft and axles before taking them apart including propeller shafts and drive axles together with pinion flanges and output shafts requiring the same component assembly relation as removal steps along with published specifications and torque values. First raise the vehicle then make distinctive marks which connect the propeller shaft to the transmission or Transfer Case and rear axle pinion yoke. Eliminate the bolts as well as yoke retainers which fasten the pinion yoke to the rear axle. Do not harm the injection joints by using hammers against yoke ears or tools between the yoke and Universal Joint while removing parts. Start the propeller shaft sliding toward the front to detach it from the rear axle pinion yoke and keep sliding toward the back to disconnect it from the transmission or Transfer Case before extracting it from the vehicle. Examine the Slip Yoke splines to determine if they have enough lubricant before adding gm p/n 12345879 (Canadian P/N 10953511) or an equivalent compound that satisfies gm specification 9985830 (RWD w/ Automatic Transmission). The propeller shaft installation requires fitting into the transmission or Transfer Case followed by alignment of removal marks before connecting it to the rear axle pinion yoke through reference mark alignment. Secure the yoke retainers in place along with their bolts before screwing them until they reach 25 nm (19 ft.lbs.) torque and returning the vehicle to the ground.

OEM Chevrolet Suburban 2500 Drive Shaft

17 Drive Shafts found

Chevrolet Suburban 2500 Slip Yoke Part Number: 10390404

Chevrolet Suburban 2500 Drive Shaft Part Number: 84675732

Chevrolet Suburban 2500 Drive Shaft, Front Part Number: 84669663

Chevrolet Suburban 2500 Drive Shaft, Front Part Number: 22845694

Chevrolet Suburban 2500 Drive Shaft Part Number: 20912713

Chevrolet Suburban 2500 Drive Shaft Part Number: 15814474

Chevrolet Suburban 2500 Drive Shaft, Front Part Number: 15182094

Chevrolet Suburban 2500 Drive Shaft Assembly Part Number: 15109397

Chevrolet Suburban 2500 Shaft, Front Part Number: 26059170

Chevrolet Suburban 2500 Drive Shaft Part Number: 25804152

Chevrolet Suburban 2500 Drive Shaft Part Number: 22922244

Chevrolet Suburban 2500 Drive Shaft Part Number: 22845688

Chevrolet Suburban 2500 Drive Shaft Part Number: 15791197

Chevrolet Suburban 2500 Drive Shaft Part Number: 15791184

Chevrolet Suburban 2500 Drive Shaft, Front Part Number: 15182096

Chevrolet Suburban 2500 Drive Shaft Part Number: 15093867

Chevrolet Suburban 2500 Drive Shaft, Front Part Number: 22845693

Chevrolet Suburban 2500 Drive Shaft

Chevrolet Suburban 2500 Drive Shaft Parts and Q&A

Related Chevrolet Suburban 2500 Parts

Browse Chevrolet Suburban 2500 Drive Shaft by Years