How to replace a two-piece drive shaft on Chevrolet Silverado 1500?

Vehicle elevation and support constitute the first step for two-piece propeller shaft replacement. A permanent mark on all driveline components from propeller shafts through drive axles and pinion flanges and output shafts will assist future proper reassembly order. First detach both bolts from the rear propeller shaft along with the universal joint strap. A flat-bladed tool must be used to remove the duo-boot clamp which contains the front propeller Slip Yoke and center bearing boot. When removing the yoke ears do not strike them forcefully to prevent damaging the injection joints. Extract the rear propeller shaft from its position both in the center bearing and in the rear axle. You should note and tag the following components when using vehicles equipped with slip yokes: transmission or Transfer Case along with propeller shaft Slip Yoke and universal bearing cap and propeller shaft. Mark each surface on the transmission or Transfer Case and output shaft flange as well as universal joint bearing cap and propeller shaft when the yoke is attached to the output shaft. Unfasten both center bearing support nuts and the center bearing support itself. Before removing propeller shaft bolts and the shaft from the transmission or Transfer Case, use a jack stand to support the propeller shaft when it has the yoke connected to the output shaft. To install this shaft you must first line up reference marks which exist on the transmission or Transfer Case together with the Slip Yoke and universal bearing cap and propeller shaft followed by propeller shaft installation. First tighten all propeller shaft bolts by hand until complete installation of center bearing support bolts and their required torque specifications. After installing the transmission or Transfer Case propeller shaft along with its bolts and straps you must place the center support bearing on the frame. Tighten all center bearing support nuts to 40 nm (30 lb ft). The next step involves securing the front propeller shaft bolts with 25 nm torque before adding new boot clamps with new Slip Yoke to the front shaft. Master splines should receive alignment prior to installing the rear shaft. Clean chassis grease should be applied to both the Slip Yoke and rear propeller shaft before installing the rear piece into the front piece while proper referencing of the marks on the rear axle housing, pinion yoke, universal bearing cap, and rear propeller shaft occurs. Secure the boot and clamps onto the Slip Yoke while torquing the yoke retainer bolts to 25 nm (18 lb ft). To complete the procedure you should utilize the j 43218 and crimp the boot clamps and implement the vehicle lower support removal process.

OEM Chevrolet Silverado 1500 Drive Shaft

Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

79 Drive Shafts found

View related parts
Chevrolet Silverado 1500 Drive Shaft Assembly Part Number: 23242262
$503.86 MSRP: $1248.64
You Save: $744.78 (60%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2018 Chevrolet Silverado 1500 | Custom, High Country, LS, LT, LTZ, SSV, WT | 6 Cyl 4.3 L FLEX, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.3 L MILD HYBRID EV-GAS (MHEV), 8 Cyl 6.2 L GAS
View related parts
Chevrolet Silverado 1500 Drive Shaft Part Number: 23251126
$1286.54 MSRP: $3218.01
You Save: $1931.47 (61%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 22760943
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2018 Chevrolet Silverado 1500 | Custom, LS, LT, WT | 6 Cyl 4.3 L FLEX
View related parts
Chevrolet Silverado 1500 Drive Shaft Part Number: 23508419
$1301.53 MSRP: $2878.34
You Save: $1576.81 (55%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Front & Rear Propeller; Driveshaft; Shaft, Propeller
- Position: Front and Rear
- Replaces: 23251179, 22760962, 23423781, 23184397
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2018 Chevrolet Silverado 1500 | Custom, High Country, LS, LT, LTZ, SSV, WT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.3 L MILD HYBRID EV-GAS (MHEV)
View related parts
Chevrolet Silverado 1500 Drive Shaft, Front Part Number: 22760960
$394.54 MSRP: $696.20
You Save: $301.66 (44%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Front Axle Propeller; Driveshaft; Drive Shaft Assembly; Shaft, Propeller
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2019 Chevrolet Silverado 1500 | Custom, Custom Trail Boss, High Country, LS, LT, LT Trail Boss, LTZ, RST, SSV, WT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.3 L MILD HYBRID EV-GAS (MHEV), 8 Cyl 6.2 L GAS
View related parts
Chevrolet Silverado 1500 Drive Shaft, Front Part Number: 84669663
$299.24 MSRP: $624.71
You Save: $325.47 (53%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Front Axle Propeller; Driveshaft; Shaft, Propeller
- Position: Front
- Replaces: 15182098, 84060396, 15090195, 15719954
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007 Chevrolet Silverado 1500 | LS, LT, LTZ, WT | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Silverado 1500 Drive Shaft, Front Part Number: 22760959
$328.93 MSRP: $579.32
You Save: $250.39 (44%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Front Axle Propeller; Driveshaft; Drive Shaft Assembly; Shaft, Propeller
- Position: Front
- Replaces: 23180816
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2018 Chevrolet Silverado 1500 | Custom, High Country, LS, LT, LTZ, SSV, WT | 6 Cyl 4.3 L FLEX, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.3 L MILD HYBRID EV-GAS (MHEV), 8 Cyl 6.2 L GAS
View related parts
Chevrolet Silverado 1500 Drive Shaft Part Number: 23508418
$1145.68 MSRP: $1946.60
You Save: $800.92 (42%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Front & Rear Propeller; Driveshaft; Shaft, Propeller
- Position: Front and Rear
- Replaces: 22760961, 23423780, 23184396, 23251178
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2018 Chevrolet Silverado 1500 | Custom, LS, LT, WT | 6 Cyl 4.3 L FLEX
View related parts
Chevrolet Silverado 1500 Drive Shaft Part Number: 23370122
$329.19 MSRP: $517.86
You Save: $188.67 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2019-2023 Chevrolet Silverado 1500 | Custom, Custom Trail Boss, WT | 4 Cyl 2.7 L GAS, 6 Cyl 4.3 L GAS
View related parts
Chevrolet Silverado 1500 Drive Shaft Part Number: 84907480
$558.18 MSRP: $886.03
You Save: $327.85 (37%)
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaced by: 85731728
- Replaces: 23370117
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2019-2023 Chevrolet Silverado 1500 | Custom, Custom Trail Boss, LT, LT Trail Boss, RST, WT | 4 Cyl 2.7 L GAS
View related parts
Chevrolet Silverado 1500 Drive Shaft, Front Part Number: 85519801
$235.73 MSRP: $388.23
You Save: $152.50 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Front Axle Propeller; Shaft, Propeller
- Position: Front
- Replaces: 23370092
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2019-2023 Chevrolet Silverado 1500 | Custom, Custom Trail Boss, LT, LT Trail Boss, RST, WT | 4 Cyl 2.7 L GAS
View related parts
Chevrolet Silverado 1500 Drive Shaft Part Number: 23370108
$371.65 MSRP: $612.09
You Save: $240.44 (40%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaced by: 84907475
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2019-2023 Chevrolet Silverado 1500 | Custom, Custom Trail Boss, High Country, LT, LTZ, RST, SSV, WT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Silverado 1500 Drive Shaft Part Number: 84907478
$567.75 MSRP: $901.40
You Save: $333.65 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 23370115
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2019-2021 Chevrolet Silverado 1500 | Custom, Custom Trail Boss, WT | 6 Cyl 4.3 L GAS
View related parts
Chevrolet Silverado 1500 Drive Shaft Part Number: 23370107
$338.61 MSRP: $532.66
You Save: $194.05 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2019-2021 Chevrolet Silverado 1500 | Custom, Custom Trail Boss, WT | 6 Cyl 4.3 L GAS
View related parts
Chevrolet Silverado 1500 Drive Shaft Part Number: 84997517
$588.62 MSRP: $1010.94
You Save: $422.32 (42%)
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Shaft, Propeller
- Replaces: 84907494, 84922904, 84500378
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2019-2021 Chevrolet Silverado 1500 | Custom, Custom Trail Boss, WT | 6 Cyl 4.3 L GAS
View related parts
Chevrolet Silverado 1500 Drive Shaft Part Number: 23508420
$129.84 MSRP: $204.30
You Save: $74.46 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Front & Rear Propeller; Driveshaft; Shaft, Propeller
- Position: Front and Rear
- Replaces: 23251180, 23184398, 23423782
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2018 Chevrolet Silverado 1500 | Custom, High Country, LS, LT, LTZ, SSV, WT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.3 L MILD HYBRID EV-GAS (MHEV), 8 Cyl 6.2 L GAS
View related parts
Chevrolet Silverado 1500 Drive Shaft Part Number: 23370123
$301.04 MSRP: $473.56
You Save: $172.52 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Shaft, Propeller
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021 Chevrolet Silverado 1500 | WT | 6 Cyl 4.3 L GAS
View related parts
Chevrolet Silverado 1500 Drive Shaft Part Number: 84907491
$503.36 MSRP: $799.00
You Save: $295.64 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Propeller; Shaft, Propeller
- Replaces: 84318914
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2020-2023 Chevrolet Silverado 1500 | Custom Trail Boss, High Country, LT, LT Trail Boss, LTZ, RST | 6 Cyl 3.0 L DIESEL
View related parts
Chevrolet Silverado 1500 Drive Shaft Part Number: 23370098
$544.18 MSRP: $859.91
You Save: $315.73 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Front & Rear Propeller; Driveshaft; Shaft, Propeller
- Position: Front and Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2019-2023 Chevrolet Silverado 1500 | Custom, Custom Trail Boss, High Country, LT, LT Trail Boss, LTZ, RST, SSV, WT | 4 Cyl 2.7 L GAS, 6 Cyl 3.0 L DIESEL, 6 Cyl 4.3 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Silverado 1500 Drive Shaft Part Number: 23370095
$544.30 MSRP: $860.10
You Save: $315.80 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Front & Rear Propeller; Driveshaft; Shaft, Propeller
- Position: Front and Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2019-2022 Chevrolet Silverado 1500 | Custom, Custom Trail Boss, LT, LT Trail Boss, LTZ, RST, WT | 4 Cyl 2.7 L GAS, 6 Cyl 3.0 L DIESEL, 6 Cyl 4.3 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Silverado 1500 Drive Shaft Part Number: 23242263
$494.28 MSRP: $1239.67
You Save: $745.39 (61%)
Product Specifications
- Other Name: Shaft Assembly-Propeller; Driveshaft; Shaft, Propeller
- Replaces: 23147491
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2018 Chevrolet Silverado 1500 | Custom, High Country, LS, LT, LTZ, SSV, WT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.3 L MILD HYBRID EV-GAS (MHEV)

| Page 1 of 4 |Next >

1-20 of 79 Results

Chevrolet Silverado 1500 Drive Shaft

Want to cut long-term maintenance and repair costs? Choose OEM Drive Shaft. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Silverado 1500 parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Silverado 1500 Drive Shaft includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

Chevrolet Silverado 1500 Drive Shaft Parts and Q&A

Drive Shaft
20912697
Q: How to replace a two-piece drive shaft on Chevrolet Silverado 1500?
A:
Vehicle elevation and support constitute the first step for two-piece propeller shaft replacement. A permanent mark on all driveline components from propeller shafts through drive axles and pinion flanges and output shafts will assist future proper reassembly order. First detach both bolts from the rear propeller shaft along with the universal joint strap. A flat-bladed tool must be used to remove the duo-boot clamp which contains the front propeller Slip Yoke and center bearing boot. When removing the yoke ears do not strike them forcefully to prevent damaging the injection joints. Extract the rear propeller shaft from its position both in the center bearing and in the rear axle. You should note and tag the following components when using vehicles equipped with slip yokes: transmission or Transfer Case along with propeller shaft Slip Yoke and universal bearing cap and propeller shaft. Mark each surface on the transmission or Transfer Case and output shaft flange as well as universal joint bearing cap and propeller shaft when the yoke is attached to the output shaft. Unfasten both center bearing support nuts and the center bearing support itself. Before removing propeller shaft bolts and the shaft from the transmission or Transfer Case, use a jack stand to support the propeller shaft when it has the yoke connected to the output shaft. To install this shaft you must first line up reference marks which exist on the transmission or Transfer Case together with the Slip Yoke and universal bearing cap and propeller shaft followed by propeller shaft installation. First tighten all propeller shaft bolts by hand until complete installation of center bearing support bolts and their required torque specifications. After installing the transmission or Transfer Case propeller shaft along with its bolts and straps you must place the center support bearing on the frame. Tighten all center bearing support nuts to 40 nm (30 lb ft). The next step involves securing the front propeller shaft bolts with 25 nm torque before adding new boot clamps with new Slip Yoke to the front shaft. Master splines should receive alignment prior to installing the rear shaft. Clean chassis grease should be applied to both the Slip Yoke and rear propeller shaft before installing the rear piece into the front piece while proper referencing of the marks on the rear axle housing, pinion yoke, universal bearing cap, and rear propeller shaft occurs. Secure the boot and clamps onto the Slip Yoke while torquing the yoke retainer bolts to 25 nm (18 lb ft). To complete the procedure you should utilize the j 43218 and crimp the boot clamps and implement the vehicle lower support removal process.