How to service and repair the front brake disc on Chevrolet Corvette?

To service and repair the front brake rotor/disc, start by raising and supporting the vehicle in an appropriate manner. Remove the tire and wheel assembly while making sure to support the brake caliper whenever you are disconnected from its mount due to hydraulic flexible brake hose being connected, failure to do so will damage the hose leading to a brake fluid leak. Then remove the brake caliper and the caliper mounting bracket as an assembly from the suspension knuckle but this time support the assembly with heavy mechanic's wire in order to avoid tension on the hydraulic brake flexible hose not disconnecting it. Move to remove the brake rotor. When installing, it becomes very important to clean off any rust or contamination from the wheel bearing flange and the brake rotor mating surfaces in order to prevent more lateral run out and brake pulsation. Clean any rust or corrosion of the wheel hub surface with the hub resurfacing kit (J 42450-A). Install the brake rotor over the wheel studs onto the wheel bearing flange. It is advisable to reinstall the brake caliper and Brake Caliper Bracket as a unit back to the suspension knuckle, a process followed by tire and wheel assembly. Finally, lower the vehicle and burnish the pads and rotors.

How to replace the front brake disc on Chevrolet Corvette?

To change the front Brake Disc lift the vehicle and support it afterwards take off the tire and wheel. Keep your fingers away from the Piston area during compressed air usage because it poses a severe damage risk to your hand. For proper fluid drainage from the master cylinder push the Piston down into the brake caliper housing. It is important to reinstall all fasteners from the beginning to keep a vehicle under control and protect its occupants. First remove the brake caliper mounting bracket bolts then disconnect the combined brake caliper unit, controlling the disc for replacement activity. Use the hub cleaning kit (J 42450-A) to clean metal surfaces at the Brake Disc hub bearing area which stops brake pulsing from developing. First install the Brake Disc and afterward place the disc brake caliper mounting bracket with brake caliper as a single unit. Use new bolts to secure the brake caliper mounting bracket and tighten them to 175 nm strength. Put back the tire and wheel combination while tightening wheel nuts in their right order to 140 nm (100 ft. Lbs.). Position the vehicle on its ground before inspecting brake fluid levels while preventing movements until you find a strong Brake Pedal because brake system air leaks may harm you. When the engine runs press the Brake Pedal gently but firmly to place the pads correctly and you should apply drum breaks if needed.

OEM Chevrolet Corvette Brake Disc

Disc Rotor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

41 Brake Discs found

View related parts
Chevrolet Corvette Rotor, Front Part Number: 19174918
$64.98 MSRP: $116.04
You Save: $51.06 (44%)
ADD TO CART
Product Specifications
- Other Name: Rotor Assembly, Front Brake; Disc Brake Hardware Kit; Brake Rotor; Rotor, Front And Rear Wheel Brake
- Position: Front
- Replaces: 14084142, 18027729
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1987 Chevrolet Corvette | Base, Indianapolis 500 Pace Car | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Rotor, Front Part Number: 84575255
$111.63 MSRP: $168.38
You Save: $56.75 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor Assembly-Front Brake; Disc Brake Hardware Kit; Brake Rotor
- Position: Front
- Replaced by: 85114492
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2020-2021 Chevrolet Corvette | Stingray | 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Rotor, Rear Part Number: 19174919
$65.91 MSRP: $117.70
You Save: $51.79 (44%)
ADD TO CART
Product Specifications
- Other Name: Rotor Assembly, Rear Brake; Brake Rotor; Rotor, Front And Rear Wheel Brake
- Position: Rear
- Replaces: 14084143, 18027740
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1987 Chevrolet Corvette | Base, Indianapolis 500 Pace Car | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Rotor, Rear Part Number: 20981820
$103.29 MSRP: $193.98
You Save: $90.69 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor-Rear Brake; Brake Rotor; Rotor, Front And Rear Wheel Brake
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014 Chevrolet Corvette | Stingray | 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Rotor, Front Part Number: 85114492
$98.64 MSRP: $202.05
You Save: $103.41 (52%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor Assembly-Front Brake; Rotor, Front And Rear Wheel Brake
- Position: Front
- Replaces: 84575255
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2020-2024 Chevrolet Corvette | E-Ray, Stingray, Z06 | 8 Cyl 5.5 L GAS, 8 Cyl 6.2 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Rotor, Rear Part Number: 85114493
$106.39 MSRP: $188.66
You Save: $82.27 (44%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor-Rear Brake; Rotor, Front And Rear Wheel Brake
- Position: Rear
- Replaces: 23429535
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2020-2024 Chevrolet Corvette | E-Ray, Stingray, Z06 | 8 Cyl 5.5 L GAS, 8 Cyl 6.2 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Rotor, Front Part Number: 84041944
$396.18 MSRP: $652.63
You Save: $256.45 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor Assembly-Front Brake; Rotor, Front And Rear Wheel Brake
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023-2024 Chevrolet Corvette | Stingray, Z06 | 8 Cyl 5.5 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Rotor, Rear Part Number: 86822032
$496.20 MSRP: $787.81
You Save: $291.61 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor-Rear Brake; Rotor, Front And Rear Wheel Brake
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023-2024 Chevrolet Corvette | Stingray, Z06 | 8 Cyl 5.5 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Rotor, Front Part Number: 84735443
$2188.63 MSRP: $3474.84
You Save: $1286.21 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor Assembly-Front Brake; Rotor, Front And Rear Wheel Brake
- Position: Front
- Replaced by: 85672270
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023-2024 Chevrolet Corvette | Stingray, Z06 | 8 Cyl 5.5 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Rotor, Rear Part Number: 84070302
$2555.06 MSRP: $4208.98
You Save: $1653.92 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor-Rear Brake; Brake Rotor; Rotor, Front And Rear Wheel Brake
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2019 Chevrolet Corvette | ZR1 | 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Rotor, Rear Part Number: 86822033
$2515.36 MSRP: $4143.58
You Save: $1628.22 (40%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor-Rear Brake; Rotor, Front And Rear Wheel Brake
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023-2024 Chevrolet Corvette | Stingray, Z06 | 8 Cyl 5.5 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Rotor, Rear Part Number: 20981826
$2366.70 MSRP: $3898.68
You Save: $1531.98 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor-Rear Brake; Brake Rotor; Rotor, Front And Rear Wheel Brake
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2019 Chevrolet Corvette | Grand Sport, Z06 | 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Rotor, Front Part Number: 84307045
$2485.39 MSRP: $4094.20
You Save: $1608.81 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor Assembly-Front Brake; Disc Brake Hardware Kit; Brake Rotor; Rotor, Front And Rear Wheel Brake
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2019 Chevrolet Corvette | ZR1 | 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Rotor, Passenger Side Part Number: 10052204
$16.92 MSRP: $91.98
You Save: $75.06 (82%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor, Front And Rear Wheel Brake; Disc Brake Hardware Kit; Brake Rotor
- Position: Passenger Side
- Replaces: 10157920
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1996 Chevrolet Corvette | 35th Anniversary Edition, 40th Anniversary Edition, Base, Collector's Edition, Grand Sport, Indianapolis 500 Pace Car, ZR-1 | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Rotor, Front Part Number: 22812086
Product Specifications
- Other Name: Rotor-Front Brake; Disc Brake Hardware Kit; Brake Rotor; Rotor, Front And Rear Wheel Brake
- Position: Front
- Replaces: 19121787
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2013 Chevrolet Corvette | 427, 427 Limited Edition Z06, Grand Sport, Z06, Z06 Carbon, ZR1 | 8 Cyl 6.2 L GAS, 8 Cyl 7.0 L GAS
View related parts
Chevrolet Corvette Rotor Part Number: 88955498
Product Specifications
- Other Name: Rotor Assembly, Rear Brake; Brake Rotor; Rotor, Front And Rear Wheel Brake
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2013 Chevrolet Corvette | 427, 427 Limited Edition Z06, Base, Grand Sport, Z06, Z06 Carbon, ZR1 | 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 7.0 L GAS
View related parts
Chevrolet Corvette Rotor, Driver Side Part Number: 10052203
Product Specifications
- Other Name: Rotor, Front And Rear Wheel Brake; Disc Brake Hardware Kit; Brake Rotor
- Position: Driver Side
- Replaces: 10157919
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1996 Chevrolet Corvette | 35th Anniversary Edition, 40th Anniversary Edition, Base, Collector's Edition, Grand Sport, Indianapolis 500 Pace Car, ZR-1 | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Rotor, Front Driver Side Part Number: 10445857
Product Specifications
- Other Name: Rotor Assembly-Front Brake; Disc Brake Hardware Kit; Brake Rotor; Rotor, Front And Rear Wheel Brake
- Position: Front Driver Side
- Replaces: 10406647
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2004 Chevrolet Corvette | 50th Anniversary Edition, 50th Anniversary Edition Pace Car, Base, Indianapolis 500 Pace Car, Z06 | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Rotor, Front Part Number: 10097654
Product Specifications
- Other Name: Rotor Assembly-Front Brake; Disc Brake Hardware Kit; Brake Rotor; Rotor, Front And Rear Wheel Brake
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1995 Chevrolet Corvette | 35th Anniversary Edition, 40th Anniversary Edition, Base, Indianapolis 500 Pace Car, ZR-1 | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Rotor, Rear Part Number: 10097655
Product Specifications
- Other Name: Rotor Assembly-Rear Brake; Brake Rotor; Rotor, Front And Rear Wheel Brake
- Position: Rear
- Replaces: 10200449
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1996 Chevrolet Corvette | 35th Anniversary Edition, 40th Anniversary Edition, Base, Collector's Edition, Grand Sport, Indianapolis 500 Pace Car, ZR-1 | 8 Cyl 5.7 L GAS

| Page 1 of 3 |Next >

1-20 of 41 Results

Chevrolet Corvette Brake Disc

Want to cut long-term maintenance and repair costs? Choose OEM Brake Disc. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Corvette parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Corvette Brake Disc includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

Brake Disc of Chevrolet Corvette cars is a crucial part of disc brake system that offers optimum clamping forces through contact area on its contact surface to enable brake pads to apply frictional force on it. Usually, found in the gray iron, these rotors can be comprised of carbon fiber or ceramic-matrix composite in the high-performance cars thus increasing the extent of heat endurance and lowering the mass. Chevrolet Corvette has installed wide range of rotors made in different types of drillings and slots aimed at increasing heat dissipation and at the same time decreasing the noise level basing on the consequence that pads wear faster. The fact that S2 rotors split the friction ring from the bell helps to maximize weight and control for thermal expansion reducing warping prospects. Warping, scarring and rusting among other things require constant check-ups and this will keep the Brake Disc as effective as possible in the Chevrolet Corvette.

Chevrolet Corvette Brake Disc Parts and Q&A

Rotor, Front Passenger Side
10445856
Q: How to service and repair the front brake disc on Chevrolet Corvette?
A:
To service and repair the front brake rotor/disc, start by raising and supporting the vehicle in an appropriate manner. Remove the tire and wheel assembly while making sure to support the brake caliper whenever you are disconnected from its mount due to hydraulic flexible brake hose being connected, failure to do so will damage the hose leading to a brake fluid leak. Then remove the brake caliper and the caliper mounting bracket as an assembly from the suspension knuckle but this time support the assembly with heavy mechanic's wire in order to avoid tension on the hydraulic brake flexible hose not disconnecting it. Move to remove the brake rotor. When installing, it becomes very important to clean off any rust or contamination from the wheel bearing flange and the brake rotor mating surfaces in order to prevent more lateral run out and brake pulsation. Clean any rust or corrosion of the wheel hub surface with the hub resurfacing kit (J 42450-A). Install the brake rotor over the wheel studs onto the wheel bearing flange. It is advisable to reinstall the brake caliper and Brake Caliper Bracket as a unit back to the suspension knuckle, a process followed by tire and wheel assembly. Finally, lower the vehicle and burnish the pads and rotors.
Rotor, Front Driver Side
10445857
Q: How to replace the front brake disc on Chevrolet Corvette?
A:
To change the front Brake Disc lift the vehicle and support it afterwards take off the tire and wheel. Keep your fingers away from the Piston area during compressed air usage because it poses a severe damage risk to your hand. For proper fluid drainage from the master cylinder push the Piston down into the brake caliper housing. It is important to reinstall all fasteners from the beginning to keep a vehicle under control and protect its occupants. First remove the brake caliper mounting bracket bolts then disconnect the combined brake caliper unit, controlling the disc for replacement activity. Use the hub cleaning kit (J 42450-A) to clean metal surfaces at the Brake Disc hub bearing area which stops brake pulsing from developing. First install the Brake Disc and afterward place the disc brake caliper mounting bracket with brake caliper as a single unit. Use new bolts to secure the brake caliper mounting bracket and tighten them to 175 nm strength. Put back the tire and wheel combination while tightening wheel nuts in their right order to 140 nm (100 ft. Lbs.). Position the vehicle on its ground before inspecting brake fluid levels while preventing movements until you find a strong Brake Pedal because brake system air leaks may harm you. When the engine runs press the Brake Pedal gently but firmly to place the pads correctly and you should apply drum breaks if needed.