How to replace the ABS Control Module on Chevrolet Corvette?

The ABS Control Module harness connector should be disconnected before turning off the ignition and then beginning to remove the ABS Control Module (ABS). Take off the 2 insulator nuts to raise the abs/brake pressure modulated valve (BPMV) above the bracket which will enable space for installing the abs and insulator mounting bolt. First step entails removing the insulator mounting bolt from the abs before moving on to the 6 abs to bpmv bolts until you can pull apart the abs from the bpmv. You can maintain usage of the reusable seal after removing it from the unit. The bpmv seal can be installed onto its cleaned surface but only when the seal remains intact. Install the abs onto the bpmv by tightening at 3 nm (27 inch lbs.) during first bolt pass and 6 nm (53 inch lbs.) during second bolt pass while following the bolt mounting sequence. The front abs insulator mounting bolt requires a new insulator if the insulator nut has been taken off and needs to be tightened to 14 nm (10 ft. Lbs.). Insert the abs/bpmv into its bracket after installing two insulator nuts which need to be tightened to 12 nm (106 inch lbs.). Reinsert the abs harness connector only when both lever sides plug into their respective receptacles and the housing can shut. The symptoms - antilock brake system test should begin while the Ignition Switch is set to the on position but engine start is prohibited.

How to remove and install the ABS Control Module on Chevrolet Corvette?

The first step to removing abs control module (ABSCM) requires stepping in to switch off the ignition to stop equipment damage. Beyond disconnecting the abscm harness connector you must remove the three insulator nuts (2,3). Raise the abscm/bpmv from the bracket until you achieve enough space for insulator bolt and abscm installation. First use a screwdriver to untighten the abscm insulator mounting bolt before withdrawing each of the abscm to bpmv securing bolts until you can easily split apart abscm from bpmv without harming the seal. The bpmv gasket surface requires alcohol cleaning with a new clean rag before installing the abscm onto the bpmv. The procedure requires replacing the insulator nut with a new one whenever removal occurs. Tighten the four bolts to reach 3 Nm and proceed to tighten each of them to 6 Nm. The front abscm insulator mounting bolt must be installed before it reaches 14 Nm torque value (10 ft. lbs.). Fasten the abscm/bpmv back into the bracket by using the three insulator nuts (2,3) and tightening them to 10 Nm (89 inch lbs.). Proceed with connecting the abscm harness connector while ensuring a complete engagement of both sides through the lever before closure. Afterward, switch on the ignition with the engine stopped. Conduct the a diagnostic system check for abs.

OEM Chevrolet Corvette ABS Control Module

Anti Lock Brake Control Module

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

28 ABS Control Modules found

View related parts
Chevrolet Corvette Control Module Part Number: 25994201
$1221.23 MSRP: $2370.18
You Save: $1148.95 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module Kit-Electronic Brake Control; ABS Control Module; Module Kit, Electronic Brake Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2010-2013 Chevrolet Corvette | 427, Base, Grand Sport, Z06, Z06 Carbon, ZR1 | 8 Cyl 6.2 L GAS, 8 Cyl 7.0 L GAS
View related parts
Chevrolet Corvette Control Module Part Number: 84244644
$412.80 MSRP: $775.22
You Save: $362.42 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module Kit-Electronic Brake Control; ABS Control Module; Module; Module Kit, Electronic Brake Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2018-2019 Chevrolet Corvette | Grand Sport, Stingray, Z06, ZR1 | 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Control Module Part Number: 13513466
$298.62 MSRP: $579.55
You Save: $280.93 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module, Electronic Brake Control; Parking Brake Control; Actuator
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2018-2019 Chevrolet Corvette | Grand Sport, Stingray, Z06, ZR1 | 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Control Module Part Number: 85115835
$222.27 MSRP: $402.30
You Save: $180.03 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Module Kit-Electronic Brake Control; ABS Control Module; Module; Module, Hydraulic Power Brake Booster; Module Kit, Electronic Brake Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2022-2024 Chevrolet Corvette | E-Ray, Stingray, Z06 | 8 Cyl 5.5 L GAS, 8 Cyl 6.2 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Control Module Part Number: 13509440
$312.61 MSRP: $612.07
You Save: $299.46 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module, Electronic Brake Control; Parking Brake Control; Actuator
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2017 Chevrolet Corvette | Grand Sport, Stingray, Z06 | 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Control Module Part Number: 23320257
$195.80 MSRP: $538.11
You Save: $342.31 (64%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module Kit, Electronic Brake Control; ABS Control Module; Module, Electronic Brake Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2017 Chevrolet Corvette | Grand Sport, Stingray, Z06 | 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Brake Pads Part Number: 85142725
$300.35 MSRP: $543.62
You Save: $243.27 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pad Kit, Brake; Front Pads
- Replaced by: 85713075
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2020-2024 Chevrolet Corvette | E-Ray, Stingray, Z06 | 8 Cyl 5.5 L GAS, 8 Cyl 6.2 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Control Module Part Number: 89060341
Product Specifications
- Other Name: Module Kit, Electronic Brake & Traction Control; ABS Control Module; Module Kit, Electronic Brake Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2008 Chevrolet Corvette | 427 Limited Edition Z06, Base, Z06 | 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 7.0 L GAS
View related parts
Chevrolet Corvette Control Module Part Number: 12216561
Product Specifications
- Other Name: Module Assembly, Electronic Brake Control; ABS Control Module; Module, Electronic Brake Control
- Replaces: 12208997
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2002 Chevrolet Corvette | Base, Z06 | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Pressure Modulator Valve Part Number: 12530740
Product Specifications
- Other Name: Valve Assembly, Brake Pressure Mode; ABS Control Module; Modulator; Valve, Electronic Brake Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2000 Chevrolet Corvette | Base, Indianapolis 500 Pace Car | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Control Module Part Number: 19244084
Product Specifications
- Other Name: Module; ABS Control Module
- Replaces: 09376711, 09367070, 9367070, 9376711
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1999-2000 Chevrolet Corvette | Base | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Control Module Part Number: 9376711
Product Specifications
- Other Name: Module Assembly, Electronic Brake Control; ABS Control Module
- Replaced by: 19244084
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1999-2000 Chevrolet Corvette | Base | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Control Module Part Number: 12521972
Product Specifications
- Other Name: Module, Electronic Brake Control; ABS Control Module
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995 Chevrolet Corvette | Base | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Control Module Part Number: 10223326
Product Specifications
- Other Name: Module, Electronic Brake Control; ABS Control Module
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1990-1991 Chevrolet Corvette | Base, ZR-1 | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Control Module Part Number: 9355246
Product Specifications
- Other Name: Module Assembly, Electronic Brake Control; ABS Control Module
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1998 Chevrolet Corvette | Base, Indianapolis 500 Pace Car | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Control Module Part Number: 10241014
Product Specifications
- Other Name: Module, Electronic Brake Control; ABS Control Module
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1995 Chevrolet Corvette | 40th Anniversary Edition, Base, Indianapolis 500 Pace Car, ZR-1 | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Modulator Valve Part Number: 12506759
Product Specifications
- Other Name: Valve, Electronic Brake Control; ABS Control Module; Modulator
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1991 Chevrolet Corvette | 35th Anniversary Edition, Base, Indianapolis 500 Pace Car, ZR-1 | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Pressure Modulator Valve Part Number: 12516323
Product Specifications
- Other Name: Valve, Electronic Brake Control; ABS Control Module; Modulator
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1995 Chevrolet Corvette | 40th Anniversary Edition, Base, Indianapolis 500 Pace Car, ZR-1 | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Pressure Modulator Valve Part Number: 12527809
Product Specifications
- Other Name: Valve Assembly, Brake Pressure Mode; ABS Control Module; Modulator; Valve, Electronic Brake Control
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1998 Chevrolet Corvette | Base, Indianapolis 500 Pace Car | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Pressure Modulator Valve Part Number: 10417038
Product Specifications
- Other Name: Valve, Electronic Brake Control; ABS Control Module; Modulator
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2000 Chevrolet Corvette | Base, Indianapolis 500 Pace Car | 8 Cyl 5.7 L GAS

| Page 1 of 2 |Next >

1-20 of 28 Results

Chevrolet Corvette ABS Control Module

Want to cut long-term maintenance and repair costs? Choose OEM ABS Control Module. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Corvette parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Corvette ABS Control Module includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

Chevrolet Corvette ABS Control Module is a component of the anti-lock braking system commonly associated with extraordinary reliability and performance enough for several Corvette generations. This highly developed component is crucial in improving the car's safety by guard against wheel locking during instances of vigorous stopping, making the car highly responsive. The Chevrolet Corvette the use of ABS Control Module avail themselves of high technological wheel speed sensors to monitor the speed of each wheel and integrated valves and a pump control the brake pressure to meet the road traction. This automation enables fast operations of the braking styles including threshold and cadence beyond the ability of a human. In the course of the years, the Chevrolet Corvette has had improvements in its ABS Control Module that has adopted aspects like the ESC and traction control since they provide efficiency in vehicle steadiness during skid and efficiency in brake force during acceleration. Despite the fact that the ABS Control Module usually reduces the stopping distances on most road surfaces Further, it is important to know how it works on loose gravel or snow. The Chevrolet Corvette, new for 2020 with a mid-engine design, offers potent engines and slick-shifting transmissions in this top-notch sports car; hence, the ABS Control Module is a crucial part of this model. As a result, the Chevrolet Corvette ABS Control Module shows a combination of efficiency, security, and modularity in its technological platform, strengthening the Corvette's place in the automotive picturesque as a vehicle cherished by driving enthusiasm.

Chevrolet Corvette ABS Control Module Parts and Q&A

Control Module
89060341
Q: How to replace the ABS Control Module on Chevrolet Corvette?
A:
The ABS Control Module harness connector should be disconnected before turning off the ignition and then beginning to remove the ABS Control Module (ABS). Take off the 2 insulator nuts to raise the abs/brake pressure modulated valve (BPMV) above the bracket which will enable space for installing the abs and insulator mounting bolt. First step entails removing the insulator mounting bolt from the abs before moving on to the 6 abs to bpmv bolts until you can pull apart the abs from the bpmv. You can maintain usage of the reusable seal after removing it from the unit. The bpmv seal can be installed onto its cleaned surface but only when the seal remains intact. Install the abs onto the bpmv by tightening at 3 nm (27 inch lbs.) during first bolt pass and 6 nm (53 inch lbs.) during second bolt pass while following the bolt mounting sequence. The front abs insulator mounting bolt requires a new insulator if the insulator nut has been taken off and needs to be tightened to 14 nm (10 ft. Lbs.). Insert the abs/bpmv into its bracket after installing two insulator nuts which need to be tightened to 12 nm (106 inch lbs.). Reinsert the abs harness connector only when both lever sides plug into their respective receptacles and the housing can shut. The symptoms - antilock brake system test should begin while the Ignition Switch is set to the on position but engine start is prohibited.
Control Module
19244084
Q: How to remove and install the ABS Control Module on Chevrolet Corvette?
A:
The first step to removing abs control module (ABSCM) requires stepping in to switch off the ignition to stop equipment damage. Beyond disconnecting the abscm harness connector you must remove the three insulator nuts (2,3). Raise the abscm/bpmv from the bracket until you achieve enough space for insulator bolt and abscm installation. First use a screwdriver to untighten the abscm insulator mounting bolt before withdrawing each of the abscm to bpmv securing bolts until you can easily split apart abscm from bpmv without harming the seal. The bpmv gasket surface requires alcohol cleaning with a new clean rag before installing the abscm onto the bpmv. The procedure requires replacing the insulator nut with a new one whenever removal occurs. Tighten the four bolts to reach 3 Nm and proceed to tighten each of them to 6 Nm. The front abscm insulator mounting bolt must be installed before it reaches 14 Nm torque value (10 ft. lbs.). Fasten the abscm/bpmv back into the bracket by using the three insulator nuts (2,3) and tightening them to 10 Nm (89 inch lbs.). Proceed with connecting the abscm harness connector while ensuring a complete engagement of both sides through the lever before closure. Afterward, switch on the ignition with the engine stopped. Conduct the a diagnostic system check for abs.