How to replace the front wheel bearing and hub on Chevrolet Corvette?

To begin hub and Wheel Bearing replacement work on this vehicle you must lift it and provide support. Take off the tire and wheel from their assembly before unplugging the Wheel Speed Sensor electrical connection. Take apart the brakes and rotor before unconnecting the lower Control Arm's stabilizer shaft link. Place the lower Control Arm on a jackstand to keep it supported during the installation steps. The j 42188 ball joint separator helps you disconnect the outer tie rod ball stud from the Steering Knuckle and the lower ball joint stud from the Steering Knuckle. Take out the hub and bearing from the Steering Knuckle after disconnecting Wheel Hub mounting bolts. Put the hub and bearing assembly into the Steering Knuckle. Then install Wheel Hub bolts and tighten them to 130 n.m (96 lb ft). Drop the jackstand once you secure the Control Arm ball stud to the Steering Knuckle. Put the Steering Knuckle tie rod ball stud through the outer steering linkage and apply it to the Steering Knuckle. First attach the Wheel Speed Sensor electrical connector before putting the stabilizer shaft link onto the lower Control Arm. Last, place the brake rotor and caliper in position. After completing the installation process lower the vehicle and put back the tire and wheel components.

How to replace the rear wheel bearing and hub on Chevrolet Corvette?

Before starting work lift and stabilize the vehicle under the appropriate conditions. Take out the tire and wheel parts before detaching the wheel speed sensor wire and the esc rear location sensor linkage. After taking off the brake caliper and rotor you need to disconnect the shock absorber esc harness connection. Loosen the suspension knuckle tie rod to replace it. Next take off the two parts - the Spindle Nut retainer and spacer. Detach the upper Control Arm from the suspension knuckle before separating it from the lower Control Arm ball joint stud. Finally, remove the suspension knuckle from the vehicle when all connections are loose. Before lifting off the hub and bearing assembly from the suspension knuckle you need to take out the Wheel Hub mounting bolts. When restoring use the designated Wheel Hub/wheel speed sensor pair of parts because front and rear areas must stay distinct. Adjust the Wheel Hub and bearing onto the suspension knuckle by fastening hub bolts to torque level 130 n.m (96 lb ft). Secure the suspension knuckle first in its position on the upper Control Arm and next on the lower Control Arm ball stud. Position both the Spindle Nut and washer on the center of the suspension knuckle then add the retainer before placing the final outer Tie Rod End stud. Put back the brake rotor and caliper unit then plug in the wheel speed sensor wiring and shock absorber esc wiring. Also connect the esc rear position sensor link. Complete the job by placing the wheel and tire on the vehicle then letting it down to the ground.

OEM Chevrolet Corvette Wheel Bearing

Hub Bearing

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

17 Wheel Bearings found

View related parts
Chevrolet Corvette Hub & Bearing, Rear Part Number: 23193306
$143.44 MSRP: $259.62
You Save: $116.18 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Rear Wheel (W/Bearing); Wheel Bearing and Hub Assembly; Wheel Bearing; Axle Bearing; Wheel Hub; Hub & Bearing Assembly; Hub, Rear Wheel
- Position: Rear
- Replaced by: 85144277
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2019 Chevrolet Corvette | Grand Sport, Stingray, Z06, ZR1 | 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Front Hub & Bearing Part Number: 22804376
$292.15 MSRP: $528.78
You Save: $236.63 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Front Wheel (W/ Bearing & Sensor); Repair Kit; Wheel Bearing; Axle Bearing; ABS Sensor; Rear Speed Sensor; Front Speed Sensor; Hub & Bearing Assembly; Front & Rear Wheel Hubs.
- Position: Front
- Replaced by: 19421347
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009-2013 Chevrolet Corvette | 427, Base, Grand Sport, Z06, Z06 Carbon, ZR1 | 8 Cyl 6.2 L GAS, 8 Cyl 7.0 L GAS
View related parts
Chevrolet Corvette Front Hub & Bearing Part Number: 20981829
$116.39 MSRP: $227.88
You Save: $111.49 (49%)
ADD TO CART
Product Specifications
- Other Name: Hub, Front Wheel; Wheel Hub Repair Kit; Wheel Bearing; Axle Bearing; Wheel Hub; Hub & Bearing
- Position: Front
- Replaced by: 85144278
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2019 Chevrolet Corvette | Grand Sport, Stingray, Z06, ZR1 | 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Front Hub & Bearing Part Number: 85150737
$117.17 MSRP: $212.08
You Save: $94.91 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub, Front Wheel
- Position: Front
- Replaced by: 87833625
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023 Chevrolet Corvette | Stingray, Z06 | 8 Cyl 5.5 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Hub Assembly, Front Part Number: 23291487
$89.65 MSRP: $162.26
You Save: $72.61 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub, Front Wheel; Wheel Bearing; Axle Bearing; Front Hub & Bearing
- Position: Front
- Replaced by: 85120533
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2020-2023 Chevrolet Corvette | Stingray, Z06 | 8 Cyl 5.5 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Wheel Bearing, Front Part Number: 457232
$29.38 MSRP: $50.52
You Save: $21.14 (42%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Front Wheel Brace; Wheel Bearings; Front Outer & Inner Bearings; Differential Side Gear Bearing.
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984 Chevrolet Corvette | Base | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Hub Assembly, Front Part Number: 87833625
$117.17 MSRP: $212.08
You Save: $94.91 (45%)
ADD TO CART
Product Specifications
- Other Name: Hub, Front Wheel
- Position: Front
- Replaces: 85150737
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023-2024 Chevrolet Corvette | Stingray, Z06 | 8 Cyl 5.5 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Hub Assembly, Front Part Number: 87833622
$103.66 MSRP: $194.66
You Save: $91.00 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub, Front Wheel; Hub, Rear Wheel
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2024 Chevrolet Corvette | E-Ray, Stingray | 8 Cyl 6.2 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Hub Assembly, Rear Part Number: 86812989
$118.30 MSRP: $214.12
You Save: $95.82 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Rear Wheel (W/Bearing); Rear Hub & Bearing; Hub, Rear Wheel
- Position: Rear
- Replaced by: 87833624
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023-2024 Chevrolet Corvette | Stingray, Z06 | 8 Cyl 5.5 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Front Hub & Bearing Part Number: 19421349
$235.86 MSRP: $457.77
You Save: $221.91 (49%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing Assembly, Front Wheel; Rear Speed Sensor; Front Speed Sensor; Hub & Bearing Assembly; Front & Rear Wheel Hubs.
- Position: Front
- Replaces: 19208046, 19208047, 13588035
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009-2013 Chevrolet Corvette | 427, Base, Grand Sport, Z06, Z06 Carbon, ZR1 | 8 Cyl 6.2 L GAS, 8 Cyl 7.0 L GAS
View related parts
Chevrolet Corvette Rear Speed Sensor Part Number: 88967288
Product Specifications
- Other Name: Hub, Rear Wheel; Wheel Bearing and Hub Assembly; ABS Sensor.; Hub & Bearing; Hub & Bearing Assembly
- Position: Rear
- Replaces: 07470571, 7470571
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2008 Chevrolet Corvette | 427 Limited Edition Z06, 50th Anniversary Edition, 50th Anniversary Edition Pace Car, Base, Indianapolis 500 Pace Car, Z06 | 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 7.0 L GAS
View related parts
Chevrolet Corvette Front Hub & Bearing Part Number: 88967287
Product Specifications
- Other Name: Hub Assembly, Front Wheel (W/Bearing & Speed Sensor); Wheel Hub Repair Kit; ABS Sensor.; Hub & Bearing; Front Speed Sensor; Hub, Front Wheel
- Position: Front
- Replaces: 07470569, 7470569
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2008 Chevrolet Corvette | 427 Limited Edition Z06, 50th Anniversary Edition, 50th Anniversary Edition Pace Car, Base, Indianapolis 500 Pace Car, Z06 | 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 7.0 L GAS
View related parts
Chevrolet Corvette Output Shaft Bearing, Rear Part Number: 12458146
Product Specifications
- Other Name: Bearing, Rear Axle Shaft; Wheel Bearing; Axle Bearing; Outer Shaft Bearing
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2004 Chevrolet Corvette | 50th Anniversary Edition, 50th Anniversary Edition Pace Car, Base, Indianapolis 500 Pace Car, Z06 | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Hub, Front Part Number: 12413041
Product Specifications
- Other Name: Hub Assembly, Front Wheel; Wheel Bearing and Hub Assembly; Wheel Hub Repair Kit; Hub, Front Wheel
- Position: Front
- Replaces: 7470551, 07470551
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1990 Chevrolet Corvette | 35th Anniversary Edition, Base, Indianapolis 500 Pace Car, ZR-1 | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Hub Part Number: 7466965
Product Specifications
- Other Name: Hub Assembly
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991 Chevrolet Corvette | Base, ZR-1 | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Hub & Bearing, Rear Part Number: 7470501
Product Specifications
- Other Name: Hub Assembly, Rear Wheel; Wheel Bearing & Hub; Axle Bearing; Wheel Hub; Hub; Hub, Rear Wheel
- Position: Rear
- Replaces: 7466945
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1996 Chevrolet Corvette | 35th Anniversary Edition, 40th Anniversary Edition, Base, Collector's Edition, Grand Sport, Indianapolis 500 Pace Car, ZR-1 | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Hub & Bearing, Front Part Number: 12413001
Product Specifications
- Other Name: Hub Assembly, Front Wheel; Wheel Bearing and Hub Assembly; Wheel Hub Repair Kit; Wheel Bearing; Axle Bearing; Wheel Hub; Hub; Hub, Front Wheel
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1996 Chevrolet Corvette | 40th Anniversary Edition, Base, Collector's Edition, Grand Sport, Indianapolis 500 Pace Car, ZR-1 | 8 Cyl 5.7 L GAS

Chevrolet Corvette Wheel Bearing

Want to cut long-term maintenance and repair costs? Choose OEM Wheel Bearing. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Corvette parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Corvette Wheel Bearing includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

Chevrolet Corvette Wheel Bearing is a component that is very crucial and sharply represents the true degree of reliability and performance driving the gap between the rotating wheel and the car. This vital component reduces the contacts, thus facilitating easy rotation while it deals with heavy loads. One more legendary vehicle that, for example, features powerful engines and great dynamics of turning, is the Chevrolet Corvette; still, all such qualities are highly sensitive to the quality of Wheel Bearings that play a critical role in allowing the vehicle to be efficient and safe. Applicable to different Corvette generations ranging from 6th to the 8th generation, the Wheel Bearing may be in a combined arrangement as Wheel HUB or in a separated form. This flexibility also applies to affecting replacement costs while also making installation easier for the owners. The new-generation Chevrolet Corvette with the switch to mid-engine layout in the year 2020 only amplifies the relevance of robust Wheel Bearings since they are central to vehicle handling at higher top velocities. Further, the Wheel Bearing is well protected to withstand contaminants ranging from dirt and water and thus proves its reliability in any condition. The Chevrolet Corvette Wheel Bearing is well known to be a product with many features that aim at durability and performance and this has placed the part at vantage point of the Corvette market. Finally, the Chevrolet Corvette, with the given specifications, and engineering depends on the Wheel Bearings to give out the much-desired performance and safety to the driving spirits.

Chevrolet Corvette Wheel Bearing Parts and Q&A

Front Hub & Bearing
88967287
Q: How to replace the front wheel bearing and hub on Chevrolet Corvette?
A:
To begin hub and Wheel Bearing replacement work on this vehicle you must lift it and provide support. Take off the tire and wheel from their assembly before unplugging the Wheel Speed Sensor electrical connection. Take apart the brakes and rotor before unconnecting the lower Control Arm's stabilizer shaft link. Place the lower Control Arm on a jackstand to keep it supported during the installation steps. The j 42188 ball joint separator helps you disconnect the outer tie rod ball stud from the Steering Knuckle and the lower ball joint stud from the Steering Knuckle. Take out the hub and bearing from the Steering Knuckle after disconnecting Wheel Hub mounting bolts. Put the hub and bearing assembly into the Steering Knuckle. Then install Wheel Hub bolts and tighten them to 130 n.m (96 lb ft). Drop the jackstand once you secure the Control Arm ball stud to the Steering Knuckle. Put the Steering Knuckle tie rod ball stud through the outer steering linkage and apply it to the Steering Knuckle. First attach the Wheel Speed Sensor electrical connector before putting the stabilizer shaft link onto the lower Control Arm. Last, place the brake rotor and caliper in position. After completing the installation process lower the vehicle and put back the tire and wheel components.
Rear Speed Sensor
88967288
Q: How to replace the rear wheel bearing and hub on Chevrolet Corvette?
A:
Before starting work lift and stabilize the vehicle under the appropriate conditions. Take out the tire and wheel parts before detaching the wheel speed sensor wire and the esc rear location sensor linkage. After taking off the brake caliper and rotor you need to disconnect the shock absorber esc harness connection. Loosen the suspension knuckle tie rod to replace it. Next take off the two parts - the Spindle Nut retainer and spacer. Detach the upper Control Arm from the suspension knuckle before separating it from the lower Control Arm ball joint stud. Finally, remove the suspension knuckle from the vehicle when all connections are loose. Before lifting off the hub and bearing assembly from the suspension knuckle you need to take out the Wheel Hub mounting bolts. When restoring use the designated Wheel Hub/wheel speed sensor pair of parts because front and rear areas must stay distinct. Adjust the Wheel Hub and bearing onto the suspension knuckle by fastening hub bolts to torque level 130 n.m (96 lb ft). Secure the suspension knuckle first in its position on the upper Control Arm and next on the lower Control Arm ball stud. Position both the Spindle Nut and washer on the center of the suspension knuckle then add the retainer before placing the final outer Tie Rod End stud. Put back the brake rotor and caliper unit then plug in the wheel speed sensor wiring and shock absorber esc wiring. Also connect the esc rear position sensor link. Complete the job by placing the wheel and tire on the vehicle then letting it down to the ground.