How to service and repair the slip yoke on Cadillac Escalade?

There are two essential tools required to service and repair the Slip Yoke: u joint bearing separator (J9522-3) and u joint bearing spacer remover (J9522-5). The replacement of a propeller shaft Slip Yoke demands replacing the adjacent Universal Joint for protecting the components from damage. Begin by removing the propeller shaft from its location while placing it horizontally on a clamp at a yoke instead of using a vise clamp for tubing. Apply marks to the propeller shaft for determining its transmission interface and its rear axle interface. The snap rings can be removed using plier pressure on their ends while a gentle tap on the bearing cup helps reduce the pressure inside. Workers should use a 30 mm (1 1/8 inch) socket to support the lower propeller shaft yoke for removing the bearing cup with the u joint bearing separator (J9522-3). The u joint bearing spacer remover (J9522-5) must be inserted between the seal and the bearing cup when the cup fails to come out fully, then the user should continue pressing. Press the opposite bearing cup out of the propeller shaft by rotating the propeller shaft with the intention to discard all reinstallation of Universal Joint components. The cross and Slip Yoke should be removed from the propeller shaft yoke to check for burrs or imperfections in the bearing cup bores. During installation, lubricate each needle bearing before placing one bearing cup half into the propeller shaft yoke. Pass the yoke ear down before inserting the crosspiece along with pressing the bearing cup until it matches the yoke ear position. Complete the same process for the other bearing cup by keeping trunnions facing forward. A technician should press the bearing cup into the yoke ear through the cross while performing installation checks to confirm proper unbinding function. After pressing until the groove of the bearing retainer appears you should place the bearing retainer. Adding chassis grease during installation may help the retainer seating process. To assist retainer seating use a dead blow hammer to apply gentle force on the yoke slightly. The installation process should be performed again for attaching the Universal Joint to the Slip Yoke.

OEM Cadillac Slip Yoke

Transmission Slip Yoke

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

28 Slip Yokes found

View related parts
Cadillac Slip Yoke, Front Part Number: 7812557
$134.58 MSRP: $229.13
You Save: $94.55 (42%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Yoke Assembly-Universal Joint Sleeve Front, W/O Vibr Damper; Driveshaft Yokes; Yoke, Universal Joint And Power Divider; Yoke, Universal Joint
- Position: Front
Fits the following Cadillac Models:
- Brougham | 1992 | Base, d'Elegance | 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS
- Fleetwood | 1993-1996 | Base, Brougham | 8 Cyl 5.7 L GAS
View related parts
Cadillac Slip Yoke, Front Part Number: 23251196
$223.22 MSRP: $547.98
You Save: $324.76 (60%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Yoke-Propeller Shaft Front Slip; Driveshaft Yokes; Yoke, Universal Joint And Power Divider
- Position: Front
- Replaces: 22944357, 07839467, 7839467, 88964470
Fits the following Cadillac Models:
- Escalade | 2009-2015 | Base, Hybrid, Hybrid Platinum, Luxury, Platinum, Premium | 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
- Escalade ESV | 2009-2014 | Base, Luxury, Platinum, Premium | 8 Cyl 6.2 L FLEX
- Escalade EXT | 2009-2012 | Base, Luxury, Premium | 8 Cyl 6.2 L FLEX
View More
View related parts
Cadillac Slip Yoke Part Number: 84389645
$70.29 MSRP: $115.77
You Save: $45.48 (40%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Yoke-Propeller Shaft Slip; Driveshaft Yokes; Yoke; Yoke, Universal Joint And Power Divider; Yoke, Universal Joint
Fits the following Cadillac Models:
- Escalade | 2021-2023 | Luxury, Premium Luxury, Premium Luxury Platinum, Sport, Sport Platinum, V | 6 Cyl 3.0 L DIESEL, 8 Cyl 6.2 L GAS
- Escalade ESV | 2021-2023 | Luxury, Premium Luxury, Premium Luxury Platinum, Sport, Sport Platinum, V | 6 Cyl 3.0 L DIESEL, 8 Cyl 6.2 L GAS
View related parts
Cadillac Slip Yoke Part Number: 88934934
$114.59 MSRP: $180.30
You Save: $65.71 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Yoke Assembly, Propeller Shaft Slip (W/Universal Joint); Driveshaft Yokes
Fits the following Cadillac Models:
- Escalade | 2002 | Base | 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Cadillac Drive Shaft Part Number: 84389646
$98.56 MSRP: $167.77
You Save: $69.21 (42%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Yoke-Propeller Shaft Slip; Driveshaft Yokes; Slip Yoke; Yoke; Yoke, Universal Joint And Power Divider
Fits the following Cadillac Models:
- Escalade | 2021-2023 | Luxury, Premium Luxury, Premium Luxury Platinum, Sport, Sport Platinum, V | 6 Cyl 3.0 L DIESEL, 8 Cyl 6.2 L GAS
- Escalade ESV | 2021-2023 | Luxury, Premium Luxury, Premium Luxury Platinum, Sport, Sport Platinum, V | 6 Cyl 3.0 L DIESEL, 8 Cyl 6.2 L GAS
View related parts
Cadillac Companion Flange Part Number: 84881462
$110.83 MSRP: $175.96
You Save: $65.13 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Yoke Kit-Differential Drive Pinion Gear; Double Cardan CV Centering Yoke; Yoke; Yoke Kit, Propeller Shaft Pinion
Fits the following Cadillac Models:
- Escalade | 2021-2023 | Premium Luxury, Premium Luxury Platinum, Sport, Sport Platinum | 6 Cyl 3.0 L DIESEL, 8 Cyl 6.2 L GAS
- Escalade ESV | 2021-2023 | Luxury, Premium Luxury, Premium Luxury Platinum, Sport, Sport Platinum | 6 Cyl 3.0 L DIESEL, 8 Cyl 6.2 L GAS
View related parts
Cadillac Companion Flange Part Number: 84584310
$327.46 MSRP: $539.43
You Save: $211.97 (40%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Yoke Kit-Front Differential Drive Pinion Gear; Yoke
- Position: Front
- Replaced by: 84798161
Fits the following Cadillac Models:
- Escalade | 2021-2023 | Luxury, Premium Luxury, Premium Luxury Platinum, Sport, Sport Platinum, V | 6 Cyl 3.0 L DIESEL, 8 Cyl 6.2 L GAS
- Escalade ESV | 2021-2023 | Luxury, Premium Luxury, Premium Luxury Platinum, Sport, Sport Platinum, V | 6 Cyl 3.0 L DIESEL, 8 Cyl 6.2 L GAS
View related parts
Cadillac Companion Flange Part Number: 85524483
$90.53 MSRP: $149.13
You Save: $58.60 (40%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Yoke Kit-Front Differential Drive Pinion Gear; Yoke; Yoke Kit, Propeller Shaft Pinion
- Replaces: 84428329
Fits the following Cadillac Models:
- Escalade | 2021-2023 | Luxury, Premium Luxury, Premium Luxury Platinum, Sport, Sport Platinum, V | 6 Cyl 3.0 L DIESEL, 8 Cyl 6.2 L GAS
- Escalade ESV | 2021-2023 | Luxury, Premium Luxury, Premium Luxury Platinum, Sport, Sport Platinum, V | 6 Cyl 3.0 L DIESEL, 8 Cyl 6.2 L GAS
View related parts
Cadillac Slip Yoke Part Number: 84868130
$112.94 MSRP: $184.85
You Save: $71.91 (39%)
ADD TO CART
Product Specifications
- Other Name: Yoke Kit-Differential Drive Pinion Gear; Double Cardan CV Centering Yoke; Driveshaft Yokes; Companion Flange; Yoke; Yoke Kit, Propeller Shaft Pinion
- Replaces: 84446298, 84833855
Fits the following Cadillac Models:
- Escalade | 2021-2023 | Luxury, Premium Luxury, Premium Luxury Platinum, Sport, Sport Platinum, V | 6 Cyl 3.0 L DIESEL, 8 Cyl 6.2 L GAS
- Escalade ESV | 2021-2023 | Luxury, Premium Luxury, Premium Luxury Platinum, Sport, Sport Platinum, V | 6 Cyl 3.0 L DIESEL, 8 Cyl 6.2 L GAS
View related parts
Cadillac Companion Flange Part Number: 12479332
$133.92 MSRP: $210.72
You Save: $76.80 (37%)
ADD TO CART
Product Specifications
- Other Name: Yoke Kit, Differential Drive Pinion Gear; Yoke; Flange; Yoke Kit, Propeller Shaft Pinion; Flange, Propeller Shaft Pinion; Yoke, Propeller Shaft Pinion
- Replaced by: 19540812
- Replaces: 12471517, 12479030
Fits the following Cadillac Models:
- Brougham | 1992 | Base, d'Elegance | 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS
- Fleetwood | 1993-1996 | Base, Brougham | 8 Cyl 5.7 L GAS
View related parts
Cadillac Slip Yoke Part Number: 89058878
Product Specifications
- Other Name: Yoke Kit, Universal Joint And Power Divider; Driveshaft Yokes
- Replaces: 88934852
Fits the following Cadillac Models:
- Escalade EXT | 2002-2006 | Base | 8 Cyl 6.0 L GAS
View related parts
Cadillac Slip Yoke Part Number: 12479384
Product Specifications
- Other Name: Yoke, Universal Joint And Power Divider; Driveshaft Yokes
- Replaces: 12471642
Fits the following Cadillac Models:
- Escalade | 2002-2005 | Base | 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Cadillac Slip Yoke Part Number: 19151749
Product Specifications
- Other Name: Yoke Kit, Universal Joint And Power Divider; Driveshaft Yokes
- Replaces: 88935866, 89058882, 89038580
Fits the following Cadillac Models:
- Escalade | 2005-2006 | Base | 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Cadillac Slip Yoke Part Number: 12542963
$62.55 MSRP: $97.98
You Save: $35.43 (37%)
Product Specifications
- Other Name: Yoke, Universal Joint And Power Divider; Driveshaft Yokes
Fits the following Cadillac Models:
- Escalade | 2003-2004 | Base | 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Cadillac Companion Flange Part Number: 26016668
Product Specifications
- Other Name: Flange; Yoke Kit, Propeller Shaft Pinion; Flange, Propeller Shaft Pinion; Yoke, Propeller Shaft Pinion
Fits the following Cadillac Models:
- Escalade | 1999-2000 | Base | 8 Cyl 5.7 L GAS
View related parts
Cadillac Companion Flange Part Number: 15634021
$87.96 MSRP: $137.79
You Save: $49.83 (37%)
Product Specifications
- Other Name: Yoke, Differential Drive Pinion Gear; Yoke, Propeller Shaft Pinion
Fits the following Cadillac Models:
- Escalade | 1999-2000 | Base | 8 Cyl 5.7 L GAS
View related parts
Cadillac Slip Yoke Part Number: 7815849
Product Specifications
- Other Name: Flange, Propeller Shaft; Driveshaft Yokes; Yoke Kit, Universal Joint And Power Divider; Yoke, Universal Joint And Power Divider; Yoke, Propeller Shaft Pinion
Fits the following Cadillac Models:
- Fleetwood | 1984 | Formal | 8 Cyl 6.0 L GAS
View related parts
Cadillac Slip Yoke Part Number: 15153615
Product Specifications
- Other Name: Yoke, Universal Joint And Power Divider; Driveshaft Yokes
- Position: Front
- Replaces: 07816706, 7816706
Fits the following Cadillac Models:
- Escalade | 1999-2000 | Base | 8 Cyl 5.7 L GAS
View related parts
Cadillac Companion Flange Part Number: 7835086
Product Specifications
- Other Name: Yoke, Differential Drive Pinion Gear; Flange, Propeller Shaft Pinion; Yoke, Propeller Shaft Pinion
Fits the following Cadillac Models:
- Fleetwood | 1984 | Formal | 8 Cyl 6.0 L GAS
View related parts
Cadillac Slip Yoke Part Number: 7801551
Product Specifications
- Other Name: Yoke, Universal Joint; Driveshaft Yokes
Fits the following Cadillac Models:
- Fleetwood | 1984 | Formal | 8 Cyl 6.0 L GAS

| Page 1 of 2 |Next >

1-20 of 28 Results

Cadillac Slip Yoke

Choose OEM Slip Yoke, you're making the optimal decision for superior quality and perfect performance. You can feel confident because each component goes through stringent quality checks. Every part is carefully built to comply with Cadillac's factory specifications. You'll enjoy a smooth, worry-free installation that fits just right. At ChevyPartsDeal.com, you'll find it easy to get top-quality OEM Cadillac Slip Yoke. You can shop at highly competitive prices and protect your budget. All our genuine Cadillac parts include a dependable manufacturer's warranty. You'll also appreciate our straightforward return policy and swift delivery services for extra convenience.

Cadillac Slip Yoke protects the trouble-free transfer of power through bending with movement of the drive train under load. Cadillac is associated with a daring style, performance, and interior comfort that can be called a personal lounge. Since 1902 origins to the handcrafted Celestiq, the brand pursues new ideas but not forgetting its chrome-lined history. Motorists adore crisp panel displays, non-fussy buttons and comfortable seats that transform their boring commutes into fast getaways. Each of the models is a combination of very fast acceleration and damp cabins, and keeps the road noise down and the grin big. State of the art batteries are placed next to roaring V-series mills so owners can choose either silence or thunder and not to be swaggering. The brand continues to learn and astonish and that proves that tradition and innovation can wear a single badge. Cadillac appeals to those who want to be driven in style. The Slip Yoke fits inside the driveline, sliding over output splines, grooves tight enough to murder chatter during bushy suspension action and to ensure that fluid stays where it is. On steep ramps or potholes, the Slip Yoke suppresses torque spikes, eliminates vibration, and eliminates hiccups of speed that may shake cargo or passengers. Fleet hearses, ambulances, and any chassis put on the lineup have faith in this part since it is inflexible against loads that are inhumane. Frequent greasing prevents the leakage of Slip Yoke splines and U-joints prior to staining driveways. Cadillac will gain as this connection remains airy since smooth power is like quality.

Cadillac Slip Yoke Parts and Q&A

Slip Yoke
7848635
Q: How to service and repair the slip yoke on Cadillac Escalade?
A:
There are two essential tools required to service and repair the Slip Yoke: u joint bearing separator (J9522-3) and u joint bearing spacer remover (J9522-5). The replacement of a propeller shaft Slip Yoke demands replacing the adjacent Universal Joint for protecting the components from damage. Begin by removing the propeller shaft from its location while placing it horizontally on a clamp at a yoke instead of using a vise clamp for tubing. Apply marks to the propeller shaft for determining its transmission interface and its rear axle interface. The snap rings can be removed using plier pressure on their ends while a gentle tap on the bearing cup helps reduce the pressure inside. Workers should use a 30 mm (1 1/8 inch) socket to support the lower propeller shaft yoke for removing the bearing cup with the u joint bearing separator (J9522-3). The u joint bearing spacer remover (J9522-5) must be inserted between the seal and the bearing cup when the cup fails to come out fully, then the user should continue pressing. Press the opposite bearing cup out of the propeller shaft by rotating the propeller shaft with the intention to discard all reinstallation of Universal Joint components. The cross and Slip Yoke should be removed from the propeller shaft yoke to check for burrs or imperfections in the bearing cup bores. During installation, lubricate each needle bearing before placing one bearing cup half into the propeller shaft yoke. Pass the yoke ear down before inserting the crosspiece along with pressing the bearing cup until it matches the yoke ear position. Complete the same process for the other bearing cup by keeping trunnions facing forward. A technician should press the bearing cup into the yoke ear through the cross while performing installation checks to confirm proper unbinding function. After pressing until the groove of the bearing retainer appears you should place the bearing retainer. Adding chassis grease during installation may help the retainer seating process. To assist retainer seating use a dead blow hammer to apply gentle force on the yoke slightly. The installation process should be performed again for attaching the Universal Joint to the Slip Yoke.