How to replace the LH Differential Cover and seal on Cadillac XLR?

To replace the Differential carrier cover and seal on the left-hand side, raise the vehicle and adequately support it. Dismount the lh rear tire and wheel assembly 02100-020-lh wheel drive shaft and the lh Muffler assembly 02020-020-lh tire wheel wells muffle duct. Drain the fluid from the Differential, then raise the Differential, then remove the left Differential mount. Clean around it of any dirt or debris and then take out the two bolts that hold the Differential cover in place and push out the dowel pin. Carefully remove the Differential cover and make sure the magnet at the bottom of the Differential case is not thrown away. Remove the o-ring seal as well as the axle seal from the Differential side cover. For installation, clean the o-ring sealing surface on the Differential cover and the Differential housing, and fix a new o-ring seal on the Differential cover. Mount the Differential cover onto the Differential, put the dowel pin and the two bolts for Differential cover retaining at work, tightening them 28 n.m (20 lb ft). Tight up the bolt containing the left Differential mount to 50 n.m (37 lb ft). Since the axle seal was successfully installed using a j 46405 output shaft seal installer, install the axle seal into the Differential cover. Add the appropriate fluids into the Differential up to the right level, then reinstall the lh Muffler assembly, the lh wheel drive shaft, and the lh rear tire and wheel assembly before lowering the vehicle.

How to replace the rear differential cover and gasket on Cadillac Escalade?

The first step to replace rear axle housing cover and gasket begins with supporting and lifting the vehicle. The procedure requires removing the Drain Plug of 9.5 inch ld and 9.5 inch hd axles or gently loosening the bolts of 8.6 inch axles before draining the rear axle. You must first take out the bolts from the rear axle cover followed by removing the axle housing cover together with its gasket . The axle housing gasket can be reused after installation unless it shows signs of damage. Start by installing the gasket before placing on the axle housing cover . Fitting the mounting bolts requires a torque of 40 n.m (30 lb ft) to tighten. To install the Drain Plug of the 9.5 inch axle confidently tighten it to 33 n.m (24 lb in). Add the fluid into the rear axle until it reaches the level 0-13 mm (0-0.50 inch) below the fill plug opening. Use appropriate fluid to fill the lubricant until it reaches the bottom of the fill plug opening when the fluid level appears low. Finally, lower the vehicle.

OEM Cadillac Differential Cover

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

24 Differential Covers found

View related parts
Cadillac Axle Cover, Rear Part Number: 22891940
$31.41 MSRP: $51.74
You Save: $20.33 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover-Rear Axle Housing; Housing Cover; Cover; Cover, Rear Axle Housing
- Position: Rear
- Replaces: 26067040, 3977386
Fits the following Cadillac Models:
- Escalade | 1999-2000 | Base | 8 Cyl 5.7 L GAS
View related parts
Cadillac Differential Cover, Rear Part Number: 25824253
$89.83 MSRP: $142.61
You Save: $52.78 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover-Rear Axle Housing; Axle Cover; Housing Cover; Cover; Cover, Rear Axle Housing
- Position: Rear
Fits the following Cadillac Models:
- Escalade | 2009-2014 | Base, Hybrid, Hybrid Platinum, Luxury, Platinum, Premium | 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L FLEX
- Escalade ESV | 2009-2014 | Base, Luxury, Platinum, Premium | 8 Cyl 6.2 L FLEX
- Escalade EXT | 2009-2013 | Base, Luxury, Premium | 8 Cyl 6.2 L FLEX
View More
View related parts
Cadillac Differential Cover Part Number: 23221119
$89.12 MSRP: $141.50
You Save: $52.38 (38%)
ADD TO CART
Product Specifications
- Other Name: Cover-Differential Carrier; Axle Cover; Cover
- Replaces: 22772342
Fits the following Cadillac Models:
- ATS | 2013-2019 | Base, Luxury, Performance, Premium, Premium Luxury, Premium Performance, V | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
- CTS | 2014-2019 | Base, Luxury, Performance, Premium, Premium Luxury, V, Vsport, Vsport Premium, Vsport Premium Luxury | 4 Cyl 2.0 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 8 Cyl 6.2 L GAS
View related parts
Cadillac Axle Cover, Rear Part Number: 19133288
$36.43 MSRP: $54.61
You Save: $18.18 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover Kit, Rear Axle Housing (9.5); Cover; Cover Kit, Rear Axle Housing
- Position: Rear
- Replaces: 12471310
Fits the following Cadillac Models:
- Escalade | 2005-2006 | Base | 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
- Escalade ESV | 2005-2006 | Base | 8 Cyl 6.0 L GAS
- Escalade EXT | 2005-2006 | Base | 8 Cyl 6.0 L GAS
View More
View related parts
Cadillac Axle Cover, Rear Part Number: 19333218
$62.01 MSRP: $105.58
You Save: $43.57 (42%)
ADD TO CART
Product Specifications
- Other Name: Cover Kit, Rear Axle Housing; Housing Cover; Cover
- Position: Rear
- Replaces: 12471640, 12471309, 15290822
Fits the following Cadillac Models:
- Escalade | 2003-2008 | Base, Platinum | 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L GAS
- Escalade ESV | 2003-2008 | Base, Platinum | 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L GAS
- Escalade EXT | 2002-2008 | Base | 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L GAS
View More
View related parts
Cadillac Axle Cover, Rear Part Number: 15634024
$82.08 MSRP: $130.32
You Save: $48.24 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover, Rear Axle Housing
- Position: Rear
Fits the following Cadillac Models:
- Escalade | 1999-2000 | Base | 8 Cyl 5.7 L GAS
View related parts
Cadillac Carrier Cover Part Number: 19132786
$130.88 MSRP: $205.93
You Save: $75.05 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Differential Cover
- Position: Driver Side
Fits the following Cadillac Models:
- XLR | 2006-2007 | Base, V | 8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS
View related parts
Cadillac Axle Cover Part Number: 12471311
$23.18 MSRP: $46.54
You Save: $23.36 (51%)
ADD TO CART
Product Specifications
- Other Name: Cover Package; Cover
- Position: Rear
Fits the following Cadillac Models:
- Escalade | 2002-2006 | Base | 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
- Escalade ESV | 2003-2006 | Base | 8 Cyl 6.0 L GAS
- Escalade EXT | 2002-2006 | Base | 8 Cyl 6.0 L GAS
View More
View related parts
Cadillac Differential Cover Part Number: 23221118
$110.34 MSRP: $181.78
You Save: $71.44 (40%)
ADD TO CART
Product Specifications
- Other Name: Cover-Differential Carrier; Axle Cover; Cover
- Replaces: 22772343
Fits the following Cadillac Models:
- ATS | 2013-2019 | Base, Luxury, Performance, Premium, Premium Luxury, Premium Performance, V | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Cadillac Axle Cover, Rear Part Number: 26067253
Product Specifications
- Other Name: Cover, Rear Axle Housing; Housing Cover; Cover
- Position: Rear
Fits the following Cadillac Models:
- Escalade | 2002-2004, 1999-2000 | Base | 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L GAS
- Escalade ESV | 2003-2005 | Base | 8 Cyl 6.0 L GAS
- Escalade EXT | 2002-2004 | Base | 8 Cyl 6.0 L GAS
View More
View related parts
Cadillac Differential Cover, Rear Part Number: 19133285
$117.73 MSRP: $185.23
You Save: $67.50 (37%)
Product Specifications
- Other Name: Cover Kit, Rear Axle Housing (9.5); Axle Cover; Cover; Cover Kit, Rear Axle Housing
- Position: Rear
Fits the following Cadillac Models:
- Escalade | 2007-2013 | Base, Hybrid, Hybrid Platinum, Luxury, Platinum, Premium | 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
- Escalade ESV | 2007-2014 | Base, Luxury, Platinum, Premium | 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
- Escalade EXT | 2007-2013 | Base, Luxury, Premium | 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View More
View related parts
Cadillac Differential Cover, Rear Part Number: 26067595
Product Specifications
- Other Name: Cover, Rear Axle Housing; Axle Cover; Housing Cover; Cover
- Position: Rear
- Replaces: 26008172
Fits the following Cadillac Models:
- Escalade | 2002-2003, 1999-2000 | Base | 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L GAS
- Escalade ESV | 2003 | Base | 8 Cyl 6.0 L GAS
- Escalade EXT | 2002 | Base | 8 Cyl 6.0 L GAS
View More
View related parts
Cadillac Axle Cover, Rear Part Number: 12471445
Product Specifications
- Other Name: Cover Kit, Rear Axle Housing; Cover
- Position: Rear
Fits the following Cadillac Models:
- Escalade | 2002-2006 | Base | 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
- Escalade ESV | 2003-2006 | Base | 8 Cyl 6.0 L GAS
- Escalade EXT | 2002-2006 | Base | 8 Cyl 6.0 L GAS
View More
View related parts
Cadillac Axle Cover Part Number: 90446834
Product Specifications
- Other Name: Cover; Cover, Rear Axle Housing
- Position: Rear
Fits the following Cadillac Models:
- Catera | 1997-2001 | Base, Sport | 6 Cyl 3.0 L GAS
View related parts
Cadillac Front Cover, Rear Part Number: 12458079
Product Specifications
- Other Name: Cover, Rear Axle Housing
- Position: Rear
Fits the following Cadillac Models:
- XLR | 2004-2009 | Base, Platinum, V | 8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS
View related parts
Cadillac Carrier Cover Part Number: 88984421
Product Specifications
- Other Name: Cover, Differential Carrier; Differential Cover; Cover
Fits the following Cadillac Models:
- CTS | 2003-2004 | Base, Luxury, Luxury Sport, V | 6 Cyl 3.2 L GAS, 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS
View related parts
Cadillac Carrier Cover Part Number: 88996685
Product Specifications
- Other Name: Cover; Differential Cover
- Position: Passenger Side
Fits the following Cadillac Models:
- XLR | 2004-2005 | Base | 8 Cyl 4.6 L GAS
View related parts
Cadillac Carrier Cover Part Number: 88996684
Product Specifications
- Other Name: Differential Cover; Cover
- Position: Driver Side
Fits the following Cadillac Models:
- XLR | 2004-2005 | Base | 8 Cyl 4.6 L GAS
View related parts
Cadillac Carrier Cover Part Number: 19132781
Product Specifications
- Other Name: Differential Cover; Cover
- Position: Driver Side
Fits the following Cadillac Models:
- XLR | 2006 | Base | 8 Cyl 4.6 L GAS
View related parts
Cadillac Differential Cover Part Number: 89058619
Product Specifications
- Other Name: Cover, Differential Carrier; Carrier Cover; Cover
Fits the following Cadillac Models:
- CTS | 2004 | Base, V | 6 Cyl 3.2 L GAS, 6 Cyl 3.6 L GAS, 8 Cyl 5.7 L GAS
- SRX | 2004-2006 | Base | 6 Cyl 3.6 L GAS, 8 Cyl 4.6 L GAS
- STS | 2005-2007 | Base | 6 Cyl 3.6 L GAS, 8 Cyl 4.6 L GAS
View More

| Page 1 of 2 |Next >

1-20 of 24 Results

Cadillac Differential Cover

Choose OEM Differential Cover, you're making the optimal decision for superior quality and perfect performance. You can feel confident because each component goes through stringent quality checks. Every part is carefully built to comply with Cadillac's factory specifications. You'll enjoy a smooth, worry-free installation that fits just right. At ChevyPartsDeal.com, you'll find it easy to get top-quality OEM Cadillac Differential Cover. You can shop at highly competitive prices and protect your budget. All our genuine Cadillac parts include a dependable manufacturer's warranty. You'll also appreciate our straightforward return policy and swift delivery services for extra convenience.

Cadillac Differential Cover prevents the spills of gear oil and ensures that the rear axle performs its duties cool and clean. Since 1902, Cadillac has pursued daring strength and plush interiors combining firm body lines with cabins resembling personal lounges. Cadillac also spends big on gigantic OLED screens and smart driving modes that allow a teenager to drive blocks through the city or a parent to go down highways as easily as possible. Cadillac startles with the artisan Celestiq, glass canopy to change its hue at any moment, displaying the badge still risks on bold innovation rather than on nostalgia. All models, including small sedans, big SUVs, appreciate silent rides, fast steering, and technology that keeps drivers calm rather than menu-oriented. Floors, listen to the exhaust, but during long hauls minimized stress in the seat massage. Differential Cover keeps the housing closed to dust or water and stray grit and the steel, aluminum, or cast-iron shell embraces the ring-and-pinion, keeping the lubricant in position where the engineers wanted it, and the gears slide without scoring or chatter even where the driver has opened the throttle body and left it open. Differential Cover comes with luxury of finishes that are chrome or powder-black finishes and reduces weight in aluminum form which helps the car accelerate and handle. Change a new gasket, tighten the bolts and Differential Cover helps differential earn its money by avoiding expensive fixes and maintaining performance mile after mile.

Cadillac Differential Cover Parts and Q&A

Carrier Cover
19132786
Q: How to replace the LH Differential Cover and seal on Cadillac XLR?
A:
To replace the Differential carrier cover and seal on the left-hand side, raise the vehicle and adequately support it. Dismount the lh rear tire and wheel assembly 02100-020-lh wheel drive shaft and the lh Muffler assembly 02020-020-lh tire wheel wells muffle duct. Drain the fluid from the Differential, then raise the Differential, then remove the left Differential mount. Clean around it of any dirt or debris and then take out the two bolts that hold the Differential cover in place and push out the dowel pin. Carefully remove the Differential cover and make sure the magnet at the bottom of the Differential case is not thrown away. Remove the o-ring seal as well as the axle seal from the Differential side cover. For installation, clean the o-ring sealing surface on the Differential cover and the Differential housing, and fix a new o-ring seal on the Differential cover. Mount the Differential cover onto the Differential, put the dowel pin and the two bolts for Differential cover retaining at work, tightening them 28 n.m (20 lb ft). Tight up the bolt containing the left Differential mount to 50 n.m (37 lb ft). Since the axle seal was successfully installed using a j 46405 output shaft seal installer, install the axle seal into the Differential cover. Add the appropriate fluids into the Differential up to the right level, then reinstall the lh Muffler assembly, the lh wheel drive shaft, and the lh rear tire and wheel assembly before lowering the vehicle.
Differential Cover, Rear
19133285
Q: How to replace the rear differential cover and gasket on Cadillac Escalade?
A:
The first step to replace rear axle housing cover and gasket begins with supporting and lifting the vehicle. The procedure requires removing the Drain Plug of 9.5 inch ld and 9.5 inch hd axles or gently loosening the bolts of 8.6 inch axles before draining the rear axle. You must first take out the bolts from the rear axle cover followed by removing the axle housing cover together with its gasket . The axle housing gasket can be reused after installation unless it shows signs of damage. Start by installing the gasket before placing on the axle housing cover . Fitting the mounting bolts requires a torque of 40 n.m (30 lb ft) to tighten. To install the Drain Plug of the 9.5 inch axle confidently tighten it to 33 n.m (24 lb in). Add the fluid into the rear axle until it reaches the level 0-13 mm (0-0.50 inch) below the fill plug opening. Use appropriate fluid to fill the lubricant until it reaches the bottom of the fill plug opening when the fluid level appears low. Finally, lower the vehicle.