How to remove and install the oil pump on Pontiac Fiero?

In order to replace the oil pump for four cylinder, it is necessary to initially take off the oil pan After that, you should unscrew the two flange mounting bolts and the nut from the main bearing cap bolt and pump as well as the screen. Then you need to fit a pump and a screen; make sure the pump shaft is parallel with the driveshaft tang while sliding to the lower bushing; if this does not work out, adjust the 'drive slot' so that the pump can slide over them. Torque the pump bolts to the required level and replace the oil pan. First for the V6 engine, set down the oil pan and draw out the pump and the driveshaft extension out as well. Screw on the oil pump and the driveshaft extension into the distributor driveshaft gear, the pump to the rear bearing cap bolt, tighten to the torque recommended before putting the oil pan back with the bolts tightened to the recommended torque. Oil all engines and for all engines check the oil level and the oil pressure and look for any sign of leakage. During the disassembly process, the residual oil should be drained from the internal chamber of the pump and the driveshaft as well as the extension should be removed; also, the pump cover and the gears should also be removed; in addition, the pressure regulator valve retaining pin and a spring should also be removed, but care should be taken when handling the spring as it releases pressure. If the valve is stuck, soaked the pump housing in carburetor cleaning solvent, and clean all the parts of the pump. The pump parts should be checked for foreign material, cracks, scoring and wear; the idler gear and shaft should fit tightly in the housing of the pump; any of the above mentioned should warrant the replacement of the pump assembly. Make sure suction pipe and screen assembly are loose and free, examine the gears for signs of wear or damage and measure gear-clash and the depth, diameter and side clearance of gears and replace the pump, if it is out of the specifications. When reassembling the pump apply engine oil to all internal parts, place the gears of the pump with their indications towards the cover, and fill all the cavities with petroleum jelly for easy priming. Place the pump cover, pressure regulator valve and spring and tighten the cover bolts in accordance to the prescribed torque. Before reinstalling the oil pan must be clean, as well as an oil pressure sending unit must be removed to fit a pressure gauge. Switch on the engine and observe the oil pressure if the suction pipe is not well anchored the oil pressure should rise quickly if it fails to do so then dismantle the oil pump, fill the cavities with petroleum jelly and then put the pump back to avoid causing harm to the engine.

How to remove and install an oil pump in V8 engine on Pontiac Firebird?

Remove the oil pan. Remove the pump-to-rear main bearing cap bolt and separate the pump and extension shaft from the engine. If installing a new oil pump, transfer the oil pump driveshaft to the new oil pump, ensuring a new nylon sleeve is in place to retain the driveshaft. To install the pump, move it into position and align the slot on the top end of the extension shaft with the drive tang on the lower end of the distributor driveshaft, as the distributor drives the oil pump, making this alignment essential; if necessary, rotate the oil pump driveshaft. Install the oil pump-to-main bearing cap bolt and tighten it to the specified torque. Reinstall the oil pan.

OEM Pontiac Oil Pump

Oil Fluid Pump

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

34 Oil Pumps found

View related parts
Pontiac Water Pump Part Number: 12640448
$134.98 MSRP: $235.54
You Save: $100.56 (43%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump, Oil; Oil Pump; Pump, Engine Oil Pump
- Replaces: 12590152, 12584298, 12590016
Fits the following Pontiac Models:
- G6 | 2007-2009 | GTP, GXP | 6 Cyl 3.6 L GAS
- G8 | 2008-2009 | Base | 6 Cyl 3.6 L GAS
- Torrent | 2008-2009 | GXP | 6 Cyl 3.6 L GAS
View More
View related parts
Pontiac Oil Pump Part Number: 12710303
$72.97 MSRP: $180.40
You Save: $107.43 (60%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump, Engine Oil Pump; Oil Pump Repair Kit
- Replaces: 12563570, 12563964, 12586665, 12696357, 12678151
Fits the following Pontiac Models:
- Firebird | 1998-2002 | Formula, Trans Am | 8 Cyl 5.7 L GAS
- G8 | 2009 | GXP | 8 Cyl 6.2 L GAS
- GTO | 2004-2006 | Base | 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L GAS
View More
View related parts
Pontiac Oil Pump Part Number: 24500960
$18.83 MSRP: $37.83
You Save: $19.00 (51%)
ADD TO CART
Product Specifications
- Other Name: Pump, Oil; Oil Pump Repair Kit; Pump, Engine Oil Pump
Fits the following Pontiac Models:
- Bonneville | 1992-1994 | SE, SSE, SSEi | 6 Cyl 3.8 L GAS
- Grand Am | 1992-1993 | GT, SE | 6 Cyl 3.3 L GAS
- Trans Sport | 1992-1994 | Base | 6 Cyl 3.8 L GAS
View More
View related parts
Pontiac Oil Pump Part Number: 93442037
$161.63 MSRP: $282.05
You Save: $120.42 (43%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump, Oil; Oil Pump Repair Kit; Pump, Engine Oil Pump
- Replaced by: 19540699
- Replaces: 12555283
Fits the following Pontiac Models:
- Firebird | 1995-1997 | Formula, Trans Am | 8 Cyl 5.7 L GAS
View related parts
Pontiac Oil Pump Part Number: 88958981
$158.20 MSRP: $317.63
You Save: $159.43 (51%)
ADD TO CART
Product Specifications
- Other Name: Pump Kit, Oil; Oil Pump Repair Kit; Pump Kit, Engine Oil Pump
- Replaces: 24576315, 24577080
Fits the following Pontiac Models:
- Sunfire | 1996-2002 | GT, SE | 4 Cyl 2.4 L GAS
View related parts
Pontiac Oil Pump Part Number: 12710304
$131.18 MSRP: $228.91
You Save: $97.73 (43%)
ADD TO CART
Product Specifications
- Other Name: Pump, Engine Oil Pump; Oil Pump Repair Kit
- Replaces: 12612289
Fits the following Pontiac Models:
- G8 | 2008-2009 | GT | 8 Cyl 6.0 L GAS
- Grand Prix | 2008 | GXP | 8 Cyl 5.3 L GAS
View related parts
Pontiac Oil Pump Part Number: 12693523
$105.03 MSRP: $173.03
You Save: $68.00 (40%)
ADD TO CART
Product Specifications
- Other Name: Pump, Engine Oil Pump; Oil Pump Repair Kit
- Replaces: 12571885
Fits the following Pontiac Models:
- Grand Prix | 2005-2007 | GXP | 8 Cyl 5.3 L GAS
View related parts
Pontiac Oil Pump Part Number: 93427692
$128.19 MSRP: $201.71
You Save: $73.52 (37%)
Product Specifications
- Other Name: Pump, Oil; Water Pump; Pump Assembly; Pump, Engine Oil Pump
- Replaces: 03848907, 12555284, 12555884, 3848907
Fits the following Pontiac Models:
- Bonneville | 1986 | Base, Brougham, LE | 6 Cyl 4.3 L GAS
- Firebird | 1984-1994 | Base, Formula, S/E, Trans Am, Trans Am GT, Trans Am GTA | 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS
View related parts
Pontiac Oil Pump Part Number: 88972778
Product Specifications
- Other Name: Pump, Oil; Oil Pump Repair Kit; Pump, Engine Oil Pump
Fits the following Pontiac Models:
- Vibe | 2003-2008 | Base | 4 Cyl 1.8 L GAS
View related parts
Pontiac Water Pump Part Number: 89060444
Product Specifications
- Other Name: Pump, Engine Oil Pump; Oil Pump
- Replaces: 10229785, 12593581
Fits the following Pontiac Models:
- Aztek | 2001-2005 | Base, GT, Rally | 6 Cyl 3.4 L GAS
- G6 | 2005-2006 | Base, GT | 6 Cyl 3.5 L GAS
- Grand Am | 1994-2005 | GT, GT1, SE, SE1, SE2 | 6 Cyl 3.1 L GAS, 6 Cyl 3.4 L GAS
- Grand Prix | 1994-2003 | Base, SE | 6 Cyl 3.1 L GAS
- Montana | 1999-2006 | Base, SV6 | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS
- Torrent | 2006-2009 | Base | 6 Cyl 3.4 L GAS
- Trans Sport | 1996-1998 | Base, Montana | 6 Cyl 3.4 L GAS
View More
View related parts
Pontiac Oil Pump Part Number: 12555384
Product Specifications
- Other Name: Pump, Engine Oil Pump; Oil Pump Repair Kit
- Replaces: 3539057, 03539057
Fits the following Pontiac Models:
- Bonneville | 2004-2005 | GXP | 8 Cyl 4.6 L GAS
View related parts
Pontiac Water Pump Part Number: 12566029
Product Specifications
- Other Name: Pump, Water; Oil Pump
Fits the following Pontiac Models:
- G6 | 2007 | GTP | 6 Cyl 3.6 L GAS
View related parts
Pontiac Oil Pump Part Number: 89017753
$120.56 MSRP: $189.71
You Save: $69.15 (37%)
Product Specifications
- Other Name: Pump, Oil; Oil Pump Repair Kit; Pump, Engine Oil Pump
Fits the following Pontiac Models:
- G6 | 2006-2010 | Base, GT, GTP | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS
- Montana | 2006 | SV6 | 6 Cyl 3.9 L GAS
View related parts
Pontiac Oil Pump Part Number: 22525287
Product Specifications
- Other Name: Pump Assembly; Oil Pump Repair Kit; Pump, Engine Oil Pump
Fits the following Pontiac Models:
- Bonneville | 1984 | Base, Brougham, LE | 8 Cyl 5.7 L DIESEL
- Grand Prix | 1984 | Base, Brougham, LE | 8 Cyl 5.7 L DIESEL
- Parisienne | 1984-1985 | Base, Brougham | 8 Cyl 5.7 L DIESEL
View More
View related parts
Pontiac Oil Pump Part Number: 10110552
Product Specifications
- Other Name: Pump Assembly; Oil Pump Repair Kit; Pump, Engine Oil Pump
Fits the following Pontiac Models:
- Grand Prix | 1989-1990 | Mclaren, SE, STE | 6 Cyl 3.1 L GAS
View related parts
Pontiac Oil Pump Part Number: 25518783
Product Specifications
- Other Name: Oil Pump Repair Kit
Fits the following Pontiac Models:
- Grand Am | 1985 | Base, LE | 6 Cyl 3.0 L GAS
View related parts
Pontiac Oil Pump Part Number: 12337732
Product Specifications
- Other Name: Oil Pump Repair Kit
Fits the following Pontiac Models:
- Firebird | 1989 | Trans Am, Trans Am GTA SE | 6 Cyl 3.8 L GAS
View related parts
Pontiac Oil Pump Part Number: 12337257
Product Specifications
- Other Name: Pump Kit, Oil (Overhaul) (Free Of Asbestos); Oil Pump Repair Kit
Fits the following Pontiac Models:
- Bonneville | 1984-1986 | Base, Brougham, LE | 6 Cyl 3.8 L GAS
- Grand Prix | 1984-1987 | Base, Brougham, LE | 6 Cyl 3.8 L GAS
- Parisienne | 1984 | Base, Brougham | 6 Cyl 3.8 L GAS
View More
View related parts
Pontiac Oil Pump Part Number: 12366006
Product Specifications
- Other Name: Pump, Engine Oil Pump; Oil Pump Repair Kit
- Replaces: 10008202, 10008206
Fits the following Pontiac Models:
- 6000 | 1984-1987 | Base, LE | 4 Cyl 2.5 L GAS
- Fiero | 1984-1988 | Base, SE, Sport, Value Leader | 4 Cyl 2.5 L GAS
- Grand Am | 1985-1987 | Base, LE, SE | 4 Cyl 2.5 L GAS
View More
View related parts
Pontiac Oil Pump Part Number: 10008206
Product Specifications
- Other Name: Pump, Engine Oil Pump; Oil Pump Repair Kit
- Replaced by: 12366006
Fits the following Pontiac Models:
- 6000 | 1984-1987 | Base, LE | 4 Cyl 2.5 L GAS
- Fiero | 1984-1988 | Base, SE, Sport, Value Leader | 4 Cyl 2.5 L GAS

| Page 1 of 2 |Next >

1-20 of 34 Results

Pontiac Oil Pump

Choose OEM Oil Pump, you're making the optimal decision for superior quality and perfect performance. You can feel confident because each component goes through stringent quality checks. Every part is carefully built to comply with Pontiac's factory specifications. You'll enjoy a smooth, worry-free installation that fits just right. At ChevyPartsDeal.com, you'll find it easy to get top-quality OEM Pontiac Oil Pump. You can shop at highly competitive prices and protect your budget. All our genuine Pontiac parts include a dependable manufacturer's warranty. You'll also appreciate our straightforward return policy and swift delivery services for extra convenience.

Pontiac Oil Pump is the core of all the engines in the series that delivers clean lubricant over critical passages to ensure that the pistons, bearings, and cams remain cool and friction-free which allows the drivers to experience the smooth power every time. The Pontiac cars are known to have bold styling, wide stance driving and attitude intertwining practicality with sportiness in everyday and in the eyes of users and enthusiasts alike, Pontiac cars boast of seats that are hugging, dashboards that are driver focused and chassis that remain composed in corners. Throughout the decades, the company had perfected the concepts of aerodynamic bodies, lightweight frames, and spirited powertrains that provide fast launches and solid highway passes without being so costly that they allow the brand a reputation of fun without compromise. Pontiac engineering deals with the involvement of the driver, clear steering reaction, and responsive braking, in which the vehicle feels eager as the key is turned. In that plucky package the Oil Pump is quietly but appreciably there, sucking oil out of the sump, pushing it through the filters, and keeping about ten psi in it all per thousand revolutions, to ensure that no metal comes into contact with metal. The Oil Pump is a gear driven pump to ensure the longevity, resistance to clogging when the owner adheres to the easy service intervals, and provides hydraulic pressure to the lifters and optional components, contributing to efficiency and engine longevity. This Oil Pump guarantees that no ride is boring or unreliable with the Pontiac performance and reliability promise.

Pontiac Oil Pump Parts and Q&A

Oil Pump
10008206
Q: How to remove and install the oil pump on Pontiac Fiero?
A:
In order to replace the oil pump for four cylinder, it is necessary to initially take off the oil pan After that, you should unscrew the two flange mounting bolts and the nut from the main bearing cap bolt and pump as well as the screen. Then you need to fit a pump and a screen; make sure the pump shaft is parallel with the driveshaft tang while sliding to the lower bushing; if this does not work out, adjust the 'drive slot' so that the pump can slide over them. Torque the pump bolts to the required level and replace the oil pan. First for the V6 engine, set down the oil pan and draw out the pump and the driveshaft extension out as well. Screw on the oil pump and the driveshaft extension into the distributor driveshaft gear, the pump to the rear bearing cap bolt, tighten to the torque recommended before putting the oil pan back with the bolts tightened to the recommended torque. Oil all engines and for all engines check the oil level and the oil pressure and look for any sign of leakage. During the disassembly process, the residual oil should be drained from the internal chamber of the pump and the driveshaft as well as the extension should be removed; also, the pump cover and the gears should also be removed; in addition, the pressure regulator valve retaining pin and a spring should also be removed, but care should be taken when handling the spring as it releases pressure. If the valve is stuck, soaked the pump housing in carburetor cleaning solvent, and clean all the parts of the pump. The pump parts should be checked for foreign material, cracks, scoring and wear; the idler gear and shaft should fit tightly in the housing of the pump; any of the above mentioned should warrant the replacement of the pump assembly. Make sure suction pipe and screen assembly are loose and free, examine the gears for signs of wear or damage and measure gear-clash and the depth, diameter and side clearance of gears and replace the pump, if it is out of the specifications. When reassembling the pump apply engine oil to all internal parts, place the gears of the pump with their indications towards the cover, and fill all the cavities with petroleum jelly for easy priming. Place the pump cover, pressure regulator valve and spring and tighten the cover bolts in accordance to the prescribed torque. Before reinstalling the oil pan must be clean, as well as an oil pressure sending unit must be removed to fit a pressure gauge. Switch on the engine and observe the oil pressure if the suction pipe is not well anchored the oil pressure should rise quickly if it fails to do so then dismantle the oil pump, fill the cavities with petroleum jelly and then put the pump back to avoid causing harm to the engine.
Oil Pump
93427692
Q: How to remove and install an oil pump in V8 engine on Pontiac Firebird?
A:
Remove the oil pan. Remove the pump-to-rear main bearing cap bolt and separate the pump and extension shaft from the engine. If installing a new oil pump, transfer the oil pump driveshaft to the new oil pump, ensuring a new nylon sleeve is in place to retain the driveshaft. To install the pump, move it into position and align the slot on the top end of the extension shaft with the drive tang on the lower end of the distributor driveshaft, as the distributor drives the oil pump, making this alignment essential; if necessary, rotate the oil pump driveshaft. Install the oil pump-to-main bearing cap bolt and tighten it to the specified torque. Reinstall the oil pan.