How to replace the rear axle shaft on a 9.75 Inch Axle on GMC Yukon XL 2500?

Vehicle upkeep begins with releasing the park brake and platform lift of your vehicle while following standard lifting procedures. First remove the tire and wheel assembly before taking away the rear steering gear assembly and Steering Knuckle assembly. After you detach the lock clip from the Axle Shaft's ending slot access point, you need to extract the clip because its springs help it retain its position inside the Axle Shaft's slot. A screwdriver or similar tool must push off the shaft end lock clip before Axle Shaft installation which can be aided through pressing the Axle Shaft forward against the gears. Do not turn the Axle Shaft when removing it because rotation may produce gear alignment issues that create reassembly complications. Fasten the new Axle Shaft by inserting the adjustable spring lock clip onto its end. You should install the Steering Knuckle assembly before adding the rear steering gear assembly and tire and wheel assembly before lowering the vehicle.

How to replace the front axle shaft on GMC Yukon XL 2500?

Then, to change the front wheel drive shaft, one must lift the car, remove the wheel and tire assembly. If available, remove the drive axle center cap. Attach a drift or a large screwdriver to ensure the drive axle wheel drive shaft cannot rotate by driving it down through the brake caliper into one of the brake rotor vanes. Leave the nut and washer from the hub and do not reuse them because a new one needs to be fitted for its use. Cut the drive shaft with your battery-powered sawzall (J 97817), and then use the axle remover (J 45859) to push the wheel drive shaft away from the hub, and take out the six bolts that hold the wheel drive shaft inboard flange to the output shaft flange in place. You should remove the drift from the rotor, and then detach the stabilizer shaft link from the lower Control Arm. Wrap shop towels around the wheel drive shaft boots (both inner & outer) to prevent damage during removal & installation, and pull the wheel drive shaft through the opening of the lower Control Arm. For installation, repeat wrapping shop towels around the boots and make sure the Steering Knuckle and wheel drive shaft splines & threads are clean and dry. Push the wheel drive shaft splined shank into the knuckle hub, and screw the washer(screw302) on, followed by the new hub nut(screw310) without actually tightening it. Mount the wheel drive shaft inboard flange on the output shaft flange by using the inboard flange bolts and packing a drift o-large screwdriver into one of the vanes of the brake rotor to prevent turning the wheel drive shaft. Tighten the inboard flange to 79 nm (58 ft. Lbs.) and the hub nut to 240 nm (177 ft. Lbs.). Take the drift out of the rotor, install the drive axle center cap, if any, reattach the stabilizer shaft link, install the wheel with a tire, and lastly, drop the car.

OEM GMC Yukon XL 2500 Axle Shaft

Car Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

33 Axle Shafts found

View related parts
GMC Yukon XL 2500 Pinion Shaft, Front Passenger Side Part Number: 19121909
$144.68 MSRP: $353.04
You Save: $208.36 (60%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft, Front Axle; Axle Shaft; Inner Shaft; Shaft
- Position: Front Passenger Side
- Replaces: 15521907
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2013 GMC Yukon XL 2500 | SLE, SLT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 8.1 L GAS
View related parts
GMC Yukon XL 2500 Axle Shaft, Rear Part Number: 22874951
$503.01 MSRP: $863.89
You Save: $360.88 (42%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft-Rear Axle; Axle Shafts; Shaft, Rear Axle Drive
- Position: Rear
- Replaces: 15286380
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2013 GMC Yukon XL 2500 | SLE, SLT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS
View related parts
GMC Yukon XL 2500 Output Shaft, Front Passenger Side Part Number: 19121908
$216.81 MSRP: $357.16
You Save: $140.35 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft, Front Axle; Axle Shaft; Inner Shaft; Shaft
- Position: Front Passenger Side
- Replaces: 15588366, 15801502, 12479219
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2013, 2000-2005 GMC Yukon XL 2500 | SLE, SLT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 8.1 L GAS
View related parts
GMC Yukon XL 2500 Axle Shaft, Front Driver Side Part Number: 26058806
$715.83 MSRP: $925.44
You Save: $209.61 (23%)
ADD TO CART
Product Specifications
- Other Name: Shaft, Front Axle; Output Shaft; Inner Shaft
- Position: Front Driver Side
- Replaces: 26059714
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2010 GMC Yukon XL 2500 | SLE, SLT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 8.1 L GAS
View related parts
GMC Yukon XL 2500 Companion Flange Part Number: 88967027
$74.62 MSRP: $118.46
You Save: $43.84 (38%)
ADD TO CART
Product Specifications
- Other Name: Flange, Propeller Shaft Pinion; Yoke, Propeller Shaft Pinion
- Position: Front
- Replaces: 15588336
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2013 GMC Yukon XL 2500 | SLE, SLT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 8.1 L GAS
View related parts
GMC Yukon XL 2500 Axle Shaft, Rear Part Number: 22943112
$310.37 MSRP: $533.02
You Save: $222.65 (42%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Rear Axle; Axle Shafts; Shaft, Rear Axle Drive
- Position: Rear
- Replaces: 15812663
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2013 GMC Yukon XL 2500 | SLE, SLT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS
View related parts
GMC Yukon XL 2500 Axle Shaft, Front Passenger Side Part Number: 15801500
$353.11 MSRP: $601.16
You Save: $248.05 (42%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft, Front Axle; Output Shaft; Inner Shaft
- Position: Front Passenger Side
- Replaces: 26058829
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2013 GMC Yukon XL 2500 | SLE, SLT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 8.1 L GAS
View related parts
GMC Yukon XL 2500 Axle Assembly, Front Part Number: 84842044
$295.97 MSRP: $508.32
You Save: $212.35 (42%)
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Front Wheel Drive Half; Axle Shaft; Shaft, Front Axle
- Position: Front
- Replaced by: 85083496
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2013 GMC Yukon XL 2500 | SLE, SLT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS
View related parts
GMC Yukon XL 2500 Output Shaft, Front Passenger Side Part Number: 15801499
$368.21 MSRP: $493.91
You Save: $125.70 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft, Front Axle; Axle Shaft; Inner Shaft
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2012 GMC Yukon XL 2500 | SLE, SLT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS
View related parts
GMC Yukon XL 2500 Axle Shaft Assembly, Front Part Number: 85126785
$343.45 MSRP: $584.72
You Save: $241.27 (42%)
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Front Wheel Drive Half; Axle Assembly; Shaft Kit, Front Axle
- Position: Front
- Replaced by: 85775028
- Replaces: 15868120, 26069242, 20875738
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2013 GMC Yukon XL 2500 | SLE, SLT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 8.1 L GAS
View related parts
GMC Yukon XL 2500 Inner Shaft, Front Part Number: 26033975
$14.51 MSRP: $36.98
You Save: $22.47 (61%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft, Front Drive Axle Shifter/Lock; Axle Shaft; Fork Shaft; Shaft
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2003 GMC Yukon XL 2500 | SLE, SLT | 8 Cyl 6.0 L GAS, 8 Cyl 8.1 L GAS
View related parts
GMC Yukon XL 2500 Output Shaft, Front Passenger Side Part Number: 22761721
$195.44 MSRP: $307.50
You Save: $112.06 (37%)
Product Specifications
- Other Name: Shaft, Front Axle; Axle Shaft; Inner Shaft
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2013 GMC Yukon XL 2500 | SLE, SLT | 8 Cyl 6.0 L FLEX
View related parts
GMC Yukon XL 2500 Output Shaft, Front Driver Side Part Number: 22761727
Product Specifications
- Other Name: Shaft, Front Axle; Axle Shaft; Inner Shaft
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2012-2013 GMC Yukon XL 2500 | SLE, SLT | 8 Cyl 6.0 L FLEX
View related parts
GMC Yukon XL 2500 Axle Shaft, Front Passenger Side Part Number: 19153230
Product Specifications
- Other Name: Shaft, Front Axle; Output Shaft; Inner Shaft
- Position: Front Passenger Side
- Replaces: 12479374
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006 GMC Yukon XL 2500 | SLE, SLT | 8 Cyl 6.0 L GAS, 8 Cyl 8.1 L GAS
View related parts
GMC Yukon XL 2500 Axle Shafts, Rear Part Number: 12471488
Product Specifications
- Other Name: Shaft, Rear Axle Drive; Axle Shaft
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2004 GMC Yukon XL 2500 | SLE, SLT | 8 Cyl 6.0 L GAS, 8 Cyl 8.1 L GAS
View related parts
GMC Yukon XL 2500 Axle Shaft, Rear Passenger Side Part Number: 12471329
Product Specifications
- Other Name: Shaft, Rear Axle Drive; Axle Shafts
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2013, 2000-2006 GMC Yukon XL 2500 | SLE, SLT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 8.1 L GAS
View related parts
GMC Yukon XL 2500 Output Shaft, Front Passenger Side Part Number: 22780163
Product Specifications
- Other Name: Shaft, Front Axle; Axle Shaft; Inner Shaft
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2012-2013 GMC Yukon XL 2500 | SLE, SLT | 8 Cyl 6.0 L FLEX
View related parts
GMC Yukon XL 2500 Shaft, Front Part Number: 26059170
Product Specifications
- Other Name: Shaft, Front Wheel Drive; Axle Shaft
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000 GMC Yukon XL 2500 | SLE, SLT | 8 Cyl 6.0 L GAS
View related parts
GMC Yukon XL 2500 Output Shaft, Front Passenger Side Part Number: 15801498
Product Specifications
- Other Name: Shaft, Front Axle; Axle Shaft; Inner Shaft
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2012 GMC Yukon XL 2500 | SLE, SLT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS
View related parts
GMC Yukon XL 2500 Axle Shaft, Rear Part Number: 26042829
Product Specifications
- Other Name: Shaft, Rear Axle Drive; Axle Shafts
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2004 GMC Yukon XL 2500 | SLE, SLT | 8 Cyl 6.0 L GAS, 8 Cyl 8.1 L GAS

| Page 1 of 2 |Next >

1-20 of 33 Results

GMC Yukon XL 2500 Axle Shaft

Want to cut long-term maintenance and repair costs? Choose OEM Axle Shaft. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine GMC Yukon XL 2500 parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM GMC Yukon XL 2500 Axle Shaft includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

GMC Yukon XL 2500 Axle Shaft Parts and Q&A

Axle Shafts, Rear
12471488
Q: How to replace the rear axle shaft on a 9.75 Inch Axle on GMC Yukon XL 2500?
A:
Vehicle upkeep begins with releasing the park brake and platform lift of your vehicle while following standard lifting procedures. First remove the tire and wheel assembly before taking away the rear steering gear assembly and Steering Knuckle assembly. After you detach the lock clip from the Axle Shaft's ending slot access point, you need to extract the clip because its springs help it retain its position inside the Axle Shaft's slot. A screwdriver or similar tool must push off the shaft end lock clip before Axle Shaft installation which can be aided through pressing the Axle Shaft forward against the gears. Do not turn the Axle Shaft when removing it because rotation may produce gear alignment issues that create reassembly complications. Fasten the new Axle Shaft by inserting the adjustable spring lock clip onto its end. You should install the Steering Knuckle assembly before adding the rear steering gear assembly and tire and wheel assembly before lowering the vehicle.
Pinion Shaft, Front Passenger Side
19121909
Q: How to replace the front axle shaft on GMC Yukon XL 2500?
A:
Then, to change the front wheel drive shaft, one must lift the car, remove the wheel and tire assembly. If available, remove the drive axle center cap. Attach a drift or a large screwdriver to ensure the drive axle wheel drive shaft cannot rotate by driving it down through the brake caliper into one of the brake rotor vanes. Leave the nut and washer from the hub and do not reuse them because a new one needs to be fitted for its use. Cut the drive shaft with your battery-powered sawzall (J 97817), and then use the axle remover (J 45859) to push the wheel drive shaft away from the hub, and take out the six bolts that hold the wheel drive shaft inboard flange to the output shaft flange in place. You should remove the drift from the rotor, and then detach the stabilizer shaft link from the lower Control Arm. Wrap shop towels around the wheel drive shaft boots (both inner & outer) to prevent damage during removal & installation, and pull the wheel drive shaft through the opening of the lower Control Arm. For installation, repeat wrapping shop towels around the boots and make sure the Steering Knuckle and wheel drive shaft splines & threads are clean and dry. Push the wheel drive shaft splined shank into the knuckle hub, and screw the washer(screw302) on, followed by the new hub nut(screw310) without actually tightening it. Mount the wheel drive shaft inboard flange on the output shaft flange by using the inboard flange bolts and packing a drift o-large screwdriver into one of the vanes of the brake rotor to prevent turning the wheel drive shaft. Tighten the inboard flange to 79 nm (58 ft. Lbs.) and the hub nut to 240 nm (177 ft. Lbs.). Take the drift out of the rotor, install the drive axle center cap, if any, reattach the stabilizer shaft link, install the wheel with a tire, and lastly, drop the car.