How to service and repair the rear Crossmember Bushing on Chevrolet Venture?

The first step for servicing or repairing the rear cross-member bushing requires using a wheel lift hoist to lift the vehicle. The vehicle requires support through its back jacking points by using utility stands to handle some of its weight. Take off the rear shock absorbers followed by disconnecting the right brake cable from its left guide loop position. Disconnect the electrical connector from the check valve of the rear differential clutch pump when working on all-wheel drive designs. Both abs wiring harnesses should be detached from frame rails before removing brake hose mounting bolts from body brackets. The alc height sensor harness connector disconnect will enable the lower position of the rear wheel lift hoist for distributing weight between utility stands. With support, pull out the Rear Crossmember mounting bolts then assist in lowering the crossmember until its front mount reaches about 114 mm (4-1/2 inches) rearward position to insert the bushing installation tool. To detach the Rear Crossmember frame mounts you need the j 45677 frame mount installer/receiver (J 45677). Mount new frame components with their voids facing forward and backward of the vehicle using the j 45677 (J 45677) tool for installation. The maintenance team should work together to position the Rear Crossmember tightly as the hoist height increases with help from the team. Follow the installation procedure to fasten the Rear Crossmember mounting bolts while tightening them to 130 nm (96 lb ft). Install the alc height sensor harness connector after beginning the process by hosting both abs wiring harnesses onto the frame rails and completing all-wheel drive requirements with the electrical connector connection to the rear differential clutch pump check valve. The right-hand park brake cable must be installed into the left guide loop while brake hose mounting bolts need to be fastened to body brackets before installing the rear shock absorbers. The process ends with checking rear suspension toe alignment followed by necessary adjustments. Reset the wheel base, release the utility stands, lower the vehicle.

OEM Chevrolet Crossmember Bushing

Crossmember Mount

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

81 Crossmember Bushings found

View related parts
Chevrolet Engine Cradle Front Bushing Part Number: 84100303
$19.19 MSRP: $28.56
You Save: $9.37 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Mount, Body To Frame Mounting; Engine Mount Bushings
- Position: Front
- Replaces: 22926964
Fits the following Chevrolet Models:
- Impala | 2014-2020 | Eco, LS, LT, LTZ, Premier | 4 Cyl 2.4 L MILD HYBRID EV-GAS (MHEV), 4 Cyl 2.5 L FLEX, 4 Cyl 2.5 L GAS, 6 Cyl 3.6 L BI-FUEL, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Crossmember Bushing Part Number: 23409018
$82.79 MSRP: $123.22
You Save: $40.43 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Mount, Body To Frame Mounting; Engine Cradle Mount Bushing; Bushing
- Position: Front
Fits the following Chevrolet Models:
- Malibu | 2016-2024 | Hybrid, L, LS, LT, Premier, RS | 4 Cyl 1.5 L GAS, 4 Cyl 1.8 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.0 L GAS
View related parts
Chevrolet Cushion, Lower Part Number: 15969969
$39.35 MSRP: $64.84
You Save: $25.49 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cushion Assembly-Body Bolt Lower; Body Mount Kit; Cushion, Body To Frame Mounting; Cushion, Radiator
- Position: Lower
Fits the following Chevrolet Models:
- Express 1500 | 1996-2014 | Base, LS, LT | 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L GAS
- Express 2500 | 1996-2024 | Base, LS, LT | 4 Cyl 2.8 L DIESEL, 6 Cyl 4.3 L FLEX, 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L BI-FUEL, 8 Cyl 5.7 L CNG, 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.5 L DIESEL, 8 Cyl 6.6 L DIESEL, 8 Cyl 6.6 L GAS
- Express 3500 | 1996-2024 | Base, LS, LT | 4 Cyl 2.8 L DIESEL, 6 Cyl 4.3 L FLEX, 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L FLEX, 8 Cyl 4.8 L GAS, 8 Cyl 5.7 L BI-FUEL, 8 Cyl 5.7 L CNG, 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.5 L DIESEL, 8 Cyl 6.6 L DIESEL, 8 Cyl 6.6 L GAS, 8 Cyl 7.4 L GAS, 8 Cyl 8.1 L GAS
- P30 | 1996-1999 | Base | 6 Cyl 4.3 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL, 8 Cyl 7.4 L GAS
View More
View related parts
Chevrolet Bushing Kit Part Number: 20871754
$108.17 MSRP: $154.78
You Save: $46.61 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator, Body To Frame Mounting
- Position: Front
- Replaces: 25872807
Fits the following Chevrolet Models:
- Equinox | 2010-2017 | L, LS, LT, LTZ, Premier | 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Bushing Kit Part Number: 25911099
$129.89 MSRP: $194.19
You Save: $64.30 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator, Body To Frame Mounting
- Position: Front
Fits the following Chevrolet Models:
- Equinox | 2010-2017 | L, LS, LT, LTZ, Premier | 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Crossmember Bushing Part Number: 84022735
$52.90 MSRP: $78.73
You Save: $25.83 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Mount, Body To Frame Mounting; Axle Support Bushing; Axle Pivot Bushing; Suspension Crossmember Front Mount
- Position: Rear
Fits the following Chevrolet Models:
- Camaro | 2016-2024 | LS, LT, LT1, SS | 4 Cyl 2.0 L GAS, 6 Cyl 3.6 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Engine Cradle Insulator Part Number: 14088027
$9.54 MSRP: $14.20
You Save: $4.66 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator, Body To Frame Mounting; Coil Spring Insulator; Insulator
- Position: Front
Fits the following Chevrolet Models:
- Lumina | 1990-2001 | Base, Euro, LS, LTZ, Z34 | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.1 L FLEX, 6 Cyl 3.1 L GAS, 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
- Monte Carlo | 1995-1999 | LS, Z34 | 6 Cyl 3.1 L GAS, 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Radiator Support Insulator Part Number: 15700841
$32.00 MSRP: $47.63
You Save: $15.63 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cushion, Body To Frame Mounting; Cushion, Radiator
- Position: Upper
Fits the following Chevrolet Models:
- S10 Blazer | 1993-1994 | Base, LT, Tahoe, Tahoe LT | 6 Cyl 4.3 L GAS
View related parts
Chevrolet Engine Cradle Lower Insulator Part Number: 10248605
$10.01 MSRP: $14.90
You Save: $4.89 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator, Body To Frame Mounting
- Position: Front
Fits the following Chevrolet Models:
- Venture | 1997-2005 | Base, LS, LT, Plus, Value, Warner Bros. | 6 Cyl 3.4 L GAS
View related parts
Chevrolet Mount Cushion Cushion, Lower Part Number: 84811201
$8.91 MSRP: $13.95
You Save: $5.04 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cushion Assembly-Body Mount Lower Locating #2; Cushion, Body To Frame Mounting
- Position: Lower
Fits the following Chevrolet Models:
- Colorado | 2023 | LT, Trail Boss, WT, Z71, ZR2 | 4 Cyl 2.7 L GAS
View related parts
Chevrolet Lower Insulator, Green, Front Part Number: 10348221
$54.88 MSRP: $81.68
You Save: $26.80 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly, Drivetrain & Front Suspension Frame *Green
- Position: Front
- Replaced by: 10306194
Fits the following Chevrolet Models:
- Impala | 2006-2013 | 50th Anniversary Edition, LS, LT, LTZ, Police, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
- Impala Limited | 2014-2016 | LS, LT, LTZ, Police | 6 Cyl 3.6 L FLEX
- Monte Carlo | 2006-2007 | LS, LT, LTZ, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
View More
View related parts
Chevrolet Crossmember Bushing Part Number: 84022736
$15.02 MSRP: $22.35
You Save: $7.33 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Mount, Body To Frame Mounting; Axle Support Bushing; Axle Pivot Bushing; Suspension Crossmember Front Mount
- Position: Rear
Fits the following Chevrolet Models:
- Camaro | 2016-2024 | LS, LT, LT1, SS | 4 Cyl 2.0 L GAS, 6 Cyl 3.6 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Crossmember Bushing Part Number: 23108389
$15.43 MSRP: $22.97
You Save: $7.54 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Mount, Body To Frame Mounting; Axle Support Bushing; Axle Pivot Bushing; Suspension Crossmember Rear Mount
- Position: Rear
Fits the following Chevrolet Models:
- Camaro | 2016-2024 | LS, LT, LT1, SS | 4 Cyl 2.0 L GAS, 6 Cyl 3.6 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Crossmember Bushing, Rear Part Number: 23369018
$51.70 MSRP: $76.95
You Save: $25.25 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator, Rear Axle Control Arm; Axle Support Bushing; Axle Pivot Bushing; Axle Beam Mount; Suspension Crossmember Rear Bushing; Suspension Crossmember Rear Mount; Mount, Body To Frame Mounting
- Position: Rear
Fits the following Chevrolet Models:
- Blazer | 2019-2024 | Base, L, LT, Premier, RS | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.6 L GAS
- Traverse | 2018-2023 | High Country, L, LS, LT, Premier, RS | 4 Cyl 2.0 L GAS, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Crossmember Bushing Part Number: 84053251
$22.75 MSRP: $33.86
You Save: $11.11 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Mount, Body To Frame Mounting; Axle Support Bushing; Axle Beam Mount
- Position: Rear
Fits the following Chevrolet Models:
- Camaro | 2017-2022 | LT1, SS, ZL1 | 8 Cyl 6.2 L GAS
View related parts
Chevrolet Crossmember Bushing Part Number: 84089600
$48.53 MSRP: $72.23
You Save: $23.70 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Mount, Body To Frame Mounting; Axle Support Bushing; Axle Beam Mount
- Position: Rear
Fits the following Chevrolet Models:
- Camaro | 2017-2022 | SS, ZL1 | 8 Cyl 6.2 L GAS
View related parts
Chevrolet Rear Insulator Part Number: 10248771
$19.82 MSRP: $28.36
You Save: $8.54 (31%)
ADD TO CART
Product Specifications
- Other Name: Insulator, Body To Frame Mounting; Engine Cradle Lower Insulator; Insulator
- Position: Front
- Replaces: 10249638, 10249847
Fits the following Chevrolet Models:
- Venture | 2005, 1997-2001 | Base, LS, LT, Plus, Value, Warner Bros. | 6 Cyl 3.4 L GAS
View related parts
Chevrolet Engine Cradle Front Bushing Part Number: 13248620
$11.94 MSRP: $17.77
You Save: $5.83 (33%)
Product Specifications
- Other Name: Insulator, Body To Frame Mounting; Engine Mount Bushings; Mount, Body To Frame Mounting
- Position: Front
Fits the following Chevrolet Models:
- Cruze | 2011-2016 | Diesel, Eco, L, LS, LT, LTZ, Premier | 4 Cyl 1.4 L GAS, 4 Cyl 1.8 L FLEX, 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L DIESEL
- Cruze Limited | 2016 | Eco, L, LS, LT, LTZ | 4 Cyl 1.4 L GAS, 4 Cyl 1.8 L FLEX, 4 Cyl 1.8 L GAS
- Volt | 2011-2015 | Base | 4 Cyl 1.4 L PLUG-IN HYBRID EV-GAS (PHEV)
View More
View related parts
Chevrolet Bushing Kit Lower Bushing Part Number: 25923353
$48.22 MSRP: $71.76
You Save: $23.54 (33%)
Product Specifications
- Other Name: Insulator, Body To Frame Mounting
- Position: Front
Fits the following Chevrolet Models:
- Equinox | 2010-2017 | L, LS, LT, LTZ, Premier | 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Engine Cradle Rear Bushing Part Number: 25866464
$35.77 MSRP: $53.24
You Save: $17.47 (33%)
Product Specifications
- Other Name: Insulator, Body To Frame Mounting; Engine Cradle Insulator
- Position: Front
Fits the following Chevrolet Models:
- Captiva Sport | 2012-2015 | LS, LT, LTZ | 4 Cyl 2.4 L FLEX, 6 Cyl 3.0 L FLEX

| Page 1 of 5 |Next >

1-20 of 81 Results

Chevrolet Crossmember Bushing

Choose OEM Crossmember Bushing, you're making the optimal decision for superior quality and perfect performance. You can feel confident because each component goes through stringent quality checks. Every part is carefully built to comply with Chevrolet's factory specifications. You'll enjoy a smooth, worry-free installation that fits just right. At ChevyPartsDeal.com, you'll find it easy to get top-quality OEM Chevrolet Crossmember Bushing. You can shop at highly competitive prices and protect your budget. All our genuine Chevrolet parts include a dependable manufacturer's warranty. You'll also appreciate our straightforward return policy and swift delivery services for extra convenience.

Chevrolet Crossmember Bushing absorbs shock in the road and prevents the suspension from moving out of line. Since 1911, Chevrolet has been driving forward everyday motoring with gutsy trucks, smooth sedans and technology that eschews gimmicks. Chevy fills it with good-driving engines with a real throb when it comes to getting on the highway or towing. Chevrolet drivers also receive convenient driver support such as Super Cruise when they want to relax on the highway. Chevy maintains low prices to allow the younger generation to take road trips without draining pockets. Long commutes no longer take the form of chores due to bold body lines and roomy cabins. The brand expanded with the help of listening to drivers as they desire power, style and ease of use with simple controls. Between the frame and the suspension link is the Crossmember Bushing which consists of tough rubber to flex and absorb the load, dampen vibration and maintain the alignment fixed and stationary even when the underbody is pounded by potholes, towing weight or sharp turns. The same stability allows Chevrolet platforms to remain silent at velocity and to steer with a feel that is not as slippy as that of cheap bushings. Install a new Crossmember Bushing several times in a lifetime and the chassis will shake off the miles without additional noise. Its new compound is also more heat resistant compared to the rubber mixes of the early stock units.

Chevrolet Crossmember Bushing Parts and Q&A

Engine Cradle Lower Insulator
10248605
Q: How to service and repair the rear Crossmember Bushing on Chevrolet Venture?
A:
The first step for servicing or repairing the rear cross-member bushing requires using a wheel lift hoist to lift the vehicle. The vehicle requires support through its back jacking points by using utility stands to handle some of its weight. Take off the rear shock absorbers followed by disconnecting the right brake cable from its left guide loop position. Disconnect the electrical connector from the check valve of the rear differential clutch pump when working on all-wheel drive designs. Both abs wiring harnesses should be detached from frame rails before removing brake hose mounting bolts from body brackets. The alc height sensor harness connector disconnect will enable the lower position of the rear wheel lift hoist for distributing weight between utility stands. With support, pull out the Rear Crossmember mounting bolts then assist in lowering the crossmember until its front mount reaches about 114 mm (4-1/2 inches) rearward position to insert the bushing installation tool. To detach the Rear Crossmember frame mounts you need the j 45677 frame mount installer/receiver (J 45677). Mount new frame components with their voids facing forward and backward of the vehicle using the j 45677 (J 45677) tool for installation. The maintenance team should work together to position the Rear Crossmember tightly as the hoist height increases with help from the team. Follow the installation procedure to fasten the Rear Crossmember mounting bolts while tightening them to 130 nm (96 lb ft). Install the alc height sensor harness connector after beginning the process by hosting both abs wiring harnesses onto the frame rails and completing all-wheel drive requirements with the electrical connector connection to the rear differential clutch pump check valve. The right-hand park brake cable must be installed into the left guide loop while brake hose mounting bolts need to be fastened to body brackets before installing the rear shock absorbers. The process ends with checking rear suspension toe alignment followed by necessary adjustments. Reset the wheel base, release the utility stands, lower the vehicle.