How to replace the rear axle shaft (8.6 Inch Axle W/JL4) on Cadillac Escalade ESV?

Your first step in replacing the rear Axle Shaft (8.6 Inch Axle W/JL4) starts with vehicle lift-up and removal of the tire and wheel assembly then the brake caliper and rear Wheel Speed Sensor. The process starts by removing the rear cover with its gasket and continues with the pinion shaft locking bolt followed by the pinion shaft itself. The Axle Shaft flange needs to move toward the Differential. A soft-faced mallet can help create clearance for the c-lock if needed. Take the c-lock off the button end of the Axle Shaft but do not rotate the shaft to prevent gear misalignment. Remove the shaft from its position in the housing. The installation requires the use of two tools: an axles remover (J 45859) and slide hammer (J 2619-01). Installation requires inserting the Axle Shaft into the rear axle housing where it should engage the Differential side gear followed by soft-faced mallet tapping to ensure proper seating of the Wheel Speed Sensor ring. Fix the lock onto the Axle Shaft's button end before pulling the shaft flange outward to position the lock correctly inside the Differential gear. Insert the pinion shaft through its hole so it matches the Differential case bolt hole before tightening a new locking bolt to 36 nm (27 ft. Lbs.). Reinstall the rear cover together with gasket followed by rear Wheel Speed Sensor or brake caliper before placing the tire and wheel assembly on. Fill the rear axle then lower the vehicle.

How to replace the front axle shaft on Cadillac Escalade ESV?

Then, to change the front wheel drive shaft, one must lift the car, remove the wheel and tire assembly. If available, remove the drive axle center cap. Attach a drift or a large screwdriver to ensure the drive axle wheel drive shaft cannot rotate by driving it down through the brake caliper into one of the brake rotor vanes. Leave the nut and washer from the hub and do not reuse them because a new one needs to be fitted for its use. Cut the drive shaft with your battery-powered sawzall (J 97817), and then use the axle remover (J 45859) to push the wheel drive shaft away from the hub, and take out the six bolts that hold the wheel drive shaft inboard flange to the output shaft flange in place. You should remove the drift from the rotor, and then detach the stabilizer shaft link from the lower Control Arm. Wrap shop towels around the wheel drive shaft boots (both inner & outer) to prevent damage during removal & installation, and pull the wheel drive shaft through the opening of the lower Control Arm. For installation, repeat wrapping shop towels around the boots and make sure the Steering Knuckle and wheel drive shaft splines & threads are clean and dry. Push the wheel drive shaft splined shank into the knuckle hub, and screw the washer(screw302) on, followed by the new hub nut(screw310) without actually tightening it. Mount the wheel drive shaft inboard flange on the output shaft flange by using the inboard flange bolts and packing a drift o-large screwdriver into one of the vanes of the brake rotor to prevent turning the wheel drive shaft. Tighten the inboard flange to 79 nm (58 ft. Lbs.) and the hub nut to 240 nm (177 ft. Lbs.). Take the drift out of the rotor, install the drive axle center cap, if any, reattach the stabilizer shaft link, install the wheel with a tire, and lastly, drop the car.

OEM Cadillac Escalade ESV Axle Shaft

Car Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

66 Axle Shafts found

View related parts
Cadillac Escalade ESV Output Shaft, Front Passenger Side Part Number: 22761721
$126.03 MSRP: $307.50
You Save: $181.47 (60%)
ADD TO CART
Product Specifications
- Other Name: Shaft, Front Axle; Axle Shaft; Inner Shaft
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2012-2014 Cadillac Escalade ESV | Base, Luxury, Platinum, Premium | 8 Cyl 6.2 L FLEX
View related parts
Cadillac Escalade ESV Pinion Shaft, Front Passenger Side Part Number: 19121909
$144.69 MSRP: $353.04
You Save: $208.35 (60%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft, Front Axle; Axle Shaft; Inner Shaft; Shaft
- Position: Passenger Side
- Replaces: 15521907
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2006 Cadillac Escalade ESV | Base | 8 Cyl 6.0 L GAS
View related parts
Cadillac Escalade ESV Axle Shaft, Rear Part Number: 23199121
$218.28 MSRP: $380.93
You Save: $162.65 (43%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft-Rear Axle; Axle Shafts; Shaft, Rear Axle Drive
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 Cadillac Escalade ESV | Base, Luxury, Platinum, Premium, Premium Luxury | 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Cadillac Escalade ESV Axle Shaft, Rear Part Number: 22943112
$313.10 MSRP: $546.35
You Save: $233.25 (43%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Rear Axle; Axle Shafts; Shaft, Rear Axle Drive
- Position: Rear
- Replaces: 15812663
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2014 Cadillac Escalade ESV | Base, Luxury, Platinum, Premium | 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Cadillac Escalade ESV Axle Shaft, Rear Part Number: 22874951
$507.44 MSRP: $885.49
You Save: $378.05 (43%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft-Rear Axle; Axle Shafts; Shaft, Rear Axle Drive
- Position: Rear
- Replaces: 15286380
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2014 Cadillac Escalade ESV | Base, Luxury, Platinum, Premium | 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Cadillac Escalade ESV Output Shaft, Front Passenger Side Part Number: 22876133
$352.05 MSRP: $589.88
You Save: $237.83 (41%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft, Front Axle; Axle Shaft; Inner Shaft; Intermed Shaft
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 Cadillac Escalade ESV | Base, Luxury, Platinum, Premium, Premium Luxury | 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Cadillac Escalade ESV Output Shaft, Front Passenger Side Part Number: 19121908
$230.58 MSRP: $366.09
You Save: $135.51 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft, Front Axle; Axle Shaft; Inner Shaft; Shaft
- Position: Passenger Side
- Replaces: 12479219, 15588366, 15801502
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020, 2003-2006 Cadillac Escalade ESV | Base, Luxury, Platinum, Premium, Premium Luxury | 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Cadillac Escalade ESV Output Shaft, Front Driver Side Part Number: 22876135
$474.41 MSRP: $762.45
You Save: $288.04 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft, Front Axle; Axle Shaft; Inner Shaft; Intermed Shaft; Flange
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 Cadillac Escalade ESV | Base, Luxury, Platinum, Premium, Premium Luxury | 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Cadillac Escalade ESV Inner Shaft, Front Part Number: 26033975
$16.83 MSRP: $36.98
You Save: $20.15 (55%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft, Front Drive Axle Shifter/Lock; Axle Shaft; Fork Shaft; Shaft
- Position: Front Inner
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003 Cadillac Escalade ESV | Base | 8 Cyl 6.0 L GAS
View related parts
Cadillac Escalade ESV Shaft Assembly-Front Wheel Drive Half Part Number: 87863488
$176.08 MSRP: $307.25
You Save: $131.17 (43%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: SHAFT ASM-FRT WHL DRV HALF
- Position: Front
- Replaces: 84477200, 84477199, 84754391
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2025 Cadillac Escalade ESV | Luxury, Premium Luxury, Premium Luxury Platinum, Sport, Sport Platinum | 6 Cyl 3.0 L DIESEL, 8 Cyl 6.2 L GAS
View related parts
Cadillac Escalade ESV Axle Assembly, Front Part Number: 84754391
$176.08 MSRP: $307.25
You Save: $131.17 (43%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Front Wheel Drive Half; Axle Shaft; Shaft, Front Axle
- Position: Front
- Replaced by: 87863488
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2025 Cadillac Escalade ESV | Luxury, Premium Luxury, Premium Luxury Platinum, Sport, Sport Platinum | 6 Cyl 3.0 L DIESEL, 8 Cyl 6.2 L GAS
View related parts
Cadillac Escalade ESV Axle Shaft Assembly, Front Part Number: 85126785
$343.45 MSRP: $599.33
You Save: $255.88 (43%)
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly-Front Wheel Drive Half; Axle Assembly; Shaft Kit, Front Axle
- Position: Front
- Replaced by: 85775028
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2005 Cadillac Escalade ESV | Base | 8 Cyl 6.0 L GAS
View related parts
Cadillac Escalade ESV Companion Flange Part Number: 88967027
$77.53 MSRP: $121.42
You Save: $43.89 (37%)
Product Specifications
- Other Name: Flange, Propeller Shaft Pinion; Yoke, Propeller Shaft Pinion
- Replaces: 15588336
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2006 Cadillac Escalade ESV | Base | 8 Cyl 6.0 L GAS
View related parts
Cadillac Escalade ESV Differential Assembly, Front Part Number: 23312177
$1206.09 MSRP: $1906.26
You Save: $700.17 (37%)
Product Specifications
- Other Name: Axle Assembly-Front; Differential
- Position: Front
- Replaces: 23484389
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 Cadillac Escalade ESV | Base, Luxury, Platinum, Premium, Premium Luxury | 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Cadillac Escalade ESV Output Shaft, Front Driver Side Part Number: 22761727
Product Specifications
- Other Name: Shaft, Front Axle; Axle Shaft; Inner Shaft
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2012-2014 Cadillac Escalade ESV | Base, Luxury, Platinum, Premium | 8 Cyl 6.2 L FLEX
View related parts
Cadillac Escalade ESV Axle Shaft, Front Passenger Side Part Number: 19153230
Product Specifications
- Other Name: Shaft, Front Axle; Output Shaft; Inner Shaft
- Position: Passenger Side
- Replaces: 12479374
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006 Cadillac Escalade ESV | Base | 8 Cyl 6.0 L GAS
View related parts
Cadillac Escalade ESV Axle Shafts, Rear Part Number: 12471488
Product Specifications
- Other Name: Shaft, Rear Axle Drive; Axle Shaft
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2004 Cadillac Escalade ESV | Base | 8 Cyl 6.0 L GAS
View related parts
Cadillac Escalade ESV Axle Shaft, Rear Passenger Side Part Number: 12471329
Product Specifications
- Other Name: Shaft, Rear Axle Drive; Axle Shafts
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2006 Cadillac Escalade ESV | Base | 8 Cyl 6.0 L GAS
View related parts
Cadillac Escalade ESV Axle Shaft Assembly, Front Part Number: 26069244
Product Specifications
- Other Name: Shaft Kit, Front Wheel Drive; CV Axle Assembly; Axle Shaft; CV Axle; Axle Assembly; Shaft Kit, Front Axle
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2006 Cadillac Escalade ESV | Base | 8 Cyl 6.0 L GAS
View related parts
Cadillac Escalade ESV Differential Assembly, Front Part Number: 23312174
Product Specifications
- Other Name: Axle Assembly-Front; Differential
- Position: Front
- Replaces: 23484385, 20980290, 23186399
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 Cadillac Escalade ESV | Base, Luxury, Platinum, Premium, Premium Luxury | 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS

| Page 1 of 4 |Next >

1-20 of 66 Results

Cadillac Escalade ESV Axle Shaft

Want to cut long-term maintenance and repair costs? Choose OEM Axle Shaft. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Cadillac Escalade ESV parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Cadillac Escalade ESV Axle Shaft includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

Cadillac Escalade ESV Axle Shaft Parts and Q&A

Axle Shafts, Rear
12471488
Q: How to replace the rear axle shaft (8.6 Inch Axle W/JL4) on Cadillac Escalade ESV?
A:
Your first step in replacing the rear Axle Shaft (8.6 Inch Axle W/JL4) starts with vehicle lift-up and removal of the tire and wheel assembly then the brake caliper and rear Wheel Speed Sensor. The process starts by removing the rear cover with its gasket and continues with the pinion shaft locking bolt followed by the pinion shaft itself. The Axle Shaft flange needs to move toward the Differential. A soft-faced mallet can help create clearance for the c-lock if needed. Take the c-lock off the button end of the Axle Shaft but do not rotate the shaft to prevent gear misalignment. Remove the shaft from its position in the housing. The installation requires the use of two tools: an axles remover (J 45859) and slide hammer (J 2619-01). Installation requires inserting the Axle Shaft into the rear axle housing where it should engage the Differential side gear followed by soft-faced mallet tapping to ensure proper seating of the Wheel Speed Sensor ring. Fix the lock onto the Axle Shaft's button end before pulling the shaft flange outward to position the lock correctly inside the Differential gear. Insert the pinion shaft through its hole so it matches the Differential case bolt hole before tightening a new locking bolt to 36 nm (27 ft. Lbs.). Reinstall the rear cover together with gasket followed by rear Wheel Speed Sensor or brake caliper before placing the tire and wheel assembly on. Fill the rear axle then lower the vehicle.
Companion Flange
88967027
Q: How to replace the front axle shaft on Cadillac Escalade ESV?
A:
Then, to change the front wheel drive shaft, one must lift the car, remove the wheel and tire assembly. If available, remove the drive axle center cap. Attach a drift or a large screwdriver to ensure the drive axle wheel drive shaft cannot rotate by driving it down through the brake caliper into one of the brake rotor vanes. Leave the nut and washer from the hub and do not reuse them because a new one needs to be fitted for its use. Cut the drive shaft with your battery-powered sawzall (J 97817), and then use the axle remover (J 45859) to push the wheel drive shaft away from the hub, and take out the six bolts that hold the wheel drive shaft inboard flange to the output shaft flange in place. You should remove the drift from the rotor, and then detach the stabilizer shaft link from the lower Control Arm. Wrap shop towels around the wheel drive shaft boots (both inner & outer) to prevent damage during removal & installation, and pull the wheel drive shaft through the opening of the lower Control Arm. For installation, repeat wrapping shop towels around the boots and make sure the Steering Knuckle and wheel drive shaft splines & threads are clean and dry. Push the wheel drive shaft splined shank into the knuckle hub, and screw the washer(screw302) on, followed by the new hub nut(screw310) without actually tightening it. Mount the wheel drive shaft inboard flange on the output shaft flange by using the inboard flange bolts and packing a drift o-large screwdriver into one of the vanes of the brake rotor to prevent turning the wheel drive shaft. Tighten the inboard flange to 79 nm (58 ft. Lbs.) and the hub nut to 240 nm (177 ft. Lbs.). Take the drift out of the rotor, install the drive axle center cap, if any, reattach the stabilizer shaft link, install the wheel with a tire, and lastly, drop the car.