How to Replace or Repair a Door Emblem on Buick Regal?

Before installation of the Regal door emblem/nameplate one must tape the mounting area and create alignment marks using additional tape. Heat the emblem/nameplate using the Heat Gun (J 25070) for thirty seconds by applying circular movement. A flat plastic tool should be used to remove or lift the emblem/nameplate because it protects the paint on panel surfaces. Clean the panel together with adhesive surface using adhesive cleaner and a lint-free clean cloth when tape stays intact on the molding. The replacement of the tape material should be done when damage occurs. Insert the foam tape to the emblem's back side before placing it on the substrate. The 3M(TM) Scotch Brite molding adhesive remover disk (3M(TM) P/N 07502) serves to remove adhesive on body panels, but plastic panels require Varnish Makers and Painters (VMP) naphtha or a 50/50 mixture of isopropyl alcohol and water to clean the adhesive. The installation environment must be kept completely dust-free. Apply VMP naphtha or alcohol-water solution to the area using a lint-free cloth before completely drying it. Apply tape markings followed by surface heating to 27-41°C (80-105°F) along with emblem/nameplate temperatures at 29-32°C (85-90°F). Place the emblem/nameplate directly onto the mounting surface where the marks indicate. Then apply regular pressure while ensuring consistent contact to achieve an even bond. After finishing the installation remove all protective tape from the mounting area.

How to replace the front emblem/nameplate on Buick LeSabre?

Before you work on the front emblem/nameplate start by applying tape to its mounting surface. Heat the emblem/nameplate with the J 25070 Heat Gun J 25070 for a circle pattern during 30 seconds. A plastic flat-blade tool removes the emblem/nameplate only from the panel surface. Prepare the mounting area by removing all old adhesive: for metal body panels use 3M(TM) Scotch Brite molding adhesive remover disks (3M(TM) P/N 07502) or equivalent tools; for plastic panels use a lint-free cloth with Varnish Makers and Painters (VMP) naphtha or a water and isopropyl alcohol mix of 50/50. Prepare the fender area by cleaning and drying it before placing the emblem over its hole. Set your J 25070 Heat Gun to 27-41°C and warm the mounting surface until it reaches 27-41°C (80-105°F). Also warm the emblem/nameplate to 29-32°C (85-90°F) before installation. Take the protective liner off the back of the emblem/nameplate without touching its adhesive side. Place it on the fender surface then push hard from all sides to make the seal permanent. Finally, remove the protective tape.

OEM Buick Emblem

Badge

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

198 Emblems found

View related parts
Buick Emblem, Rear Part Number: 13330787
$6.00 MSRP: $8.94
You Save: $2.94 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Emblem, Rear End Panel And Tailgate; Emblem,Rear End Panel And Tailgate
- Position: Rear
Fits the following Buick Models:
- Regal | 2011-2013 | Base, CXL, GS, Premium | 4 Cyl 2.0 L FLEX, 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS, 4 Cyl 2.4 L MILD HYBRID EV-GAS (MHEV)
View related parts
Buick Emblem, Front Part Number: 22867563
$40.99 MSRP: $61.01
You Save: $20.02 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Emblem, Radiator Grille And Front End Ornamentation; Emblem, Front Bumper
- Position: Front
Fits the following Buick Models:
- Regal | 2014-2017 | Base, GS, Premium, Sport Touring | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS, 4 Cyl 2.4 L MILD HYBRID EV-GAS (MHEV)
View related parts
Buick Emblem, Front Part Number: 20997971
$28.11 MSRP: $41.84
You Save: $13.73 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Emblem, Radiator Grille And Front End Ornamentation
- Position: Front
- Replaces: 13320556
Fits the following Buick Models:
- Regal | 2011-2013 | Base, CXL, GS, Premium | 4 Cyl 2.0 L FLEX, 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS, 4 Cyl 2.4 L MILD HYBRID EV-GAS (MHEV)
View related parts
Buick Emblem, Front Part Number: 25622288
$14.13 MSRP: $18.67
You Save: $4.54 (25%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Emblem, Front Fender Name; Emblem, Front Side Door
- Position: Front
Fits the following Buick Models:
- LeSabre | 1997-1999 | Custom | 6 Cyl 3.8 L GAS
View related parts
Buick Emblem, Front Part Number: 25737019
$6.75 MSRP: $9.10
You Save: $2.35 (26%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Emblem, Front Fender Name
- Position: Front
Fits the following Buick Models:
- LeSabre | 2003-2004 | Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick Emblem, Front Part Number: 25622287
$6.37 MSRP: $15.00
You Save: $8.63 (58%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Emblem, Front Side Door
- Position: Front
Fits the following Buick Models:
- LeSabre | 1997-1999 | Limited | 6 Cyl 3.8 L GAS
View related parts
Buick Nameplate, Front Part Number: 25523610
Product Specifications
- Other Name: Plate, Radiator Grille And Front End Ornamentation
- Position: Front
Fits the following Buick Models:
- LeSabre | 1986 | Custom, Limited | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Buick Nameplate, Front Part Number: 25554776
Product Specifications
- Other Name: Plate, Radiator Grille And Front End Ornamentation
- Position: Front
Fits the following Buick Models:
- LeSabre | 1992-1996 | Custom, Limited | 6 Cyl 3.8 L GAS
View related parts
Buick Nameplate, Rear Part Number: 20576640
Product Specifications
- Other Name: Plate, Rear Quarter Panel
- Position: Rear
Fits the following Buick Models:
- LeSabre | 1986-1991 | Limited | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Buick Emblem Part Number: 20569005
Product Specifications
- Other Name: Emblem, Rear Body Lock Pillar; Emblem, Center Pillar
- Position: Center Outer
Fits the following Buick Models:
- LeSabre | 1986-1991 | Base, Custom, Limited | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Buick Nameplate, Rear Part Number: 25518640
Product Specifications
- Other Name: Plate Assembly, Rear Compartment Lid Name
- Position: Rear
Fits the following Buick Models:
- Regal | 1985-1987 | Base, GNX, Grand National, Limited, T-Type | 6 Cyl 3.8 L GAS
View related parts
Buick Emblem, Front Part Number: 25517305
Product Specifications
- Other Name: Emblem, Radiator Grille And Front End Ornamentation
- Position: Front
Fits the following Buick Models:
- Electra | 1985-1990 | Limited, Park Avenue, Park Avenue Ultra, T-Type | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L DIESEL
View related parts
Buick Emblem, Front Part Number: 10446599
Product Specifications
- Other Name: Emblem, Radiator Grille And Front End Ornamentation
- Position: Front
Fits the following Buick Models:
- Regal | 2001-2004 | GS, LS | 6 Cyl 3.8 L GAS
View related parts
Buick Nameplate, Rear Part Number: 20762641
Product Specifications
- Other Name: Plate, Rear End Panel And Tailgate; Emblem,Rear End Panel And Tailgate
- Position: Rear
Fits the following Buick Models:
- LaCrosse | 2010-2011 | CXS | 6 Cyl 3.6 L GAS
View related parts
Buick Emblem, Rear Part Number: 10446576
Product Specifications
- Other Name: Plate, Rear End Panel And Tailgate; Plate,Rear End Panel And Tailgate
- Position: Rear
Fits the following Buick Models:
- Regal | 2001 | GS, LS | 6 Cyl 3.8 L GAS
View related parts
Buick Emblem Part Number: 20220594
Product Specifications
- Other Name: Emblem, Roof Side; Emblem, Roof Panel Emblem Or Plate; Emblem, Roof Panel
Fits the following Buick Models:
- Regal | 1984-1987 | Base, GNX, Grand National, Limited, T-Type | 6 Cyl 3.8 L GAS, 6 Cyl 4.1 L GAS, 6 Cyl 4.3 L DIESEL, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL
View related parts
Buick Ornament, Front Part Number: 12395304
Product Specifications
- Other Name: Ornament, Radiator Grille And Front End Ornamentation
- Position: Front
Fits the following Buick Models:
- Regal | 1989-1993 | Custom, Gran Sport, Limited | 6 Cyl 2.8 L GAS, 6 Cyl 3.1 L GAS, 6 Cyl 3.8 L GAS
View related parts
Buick Emblem, Rear Part Number: 10316010
Product Specifications
- Other Name: Plate, Rear Compartment Lid, Rear End Panel And Tailgate; Nameplate; Plate,Rear End Panel And Tailgate
- Position: Rear
Fits the following Buick Models:
- Regal | 2002-2004 | GS, LS | 6 Cyl 3.8 L GAS
View related parts
Buick Ornament, Front Part Number: 25512242
Product Specifications
- Other Name: Ornament, Radiator Grille And Front End Ornamentation
- Position: Front
Fits the following Buick Models:
- Skylark | 1984-1985 | Custom, Limited, T-Type | 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS
View related parts
Buick Ornament, Front Part Number: 25517267
Product Specifications
- Other Name: Ornament, Radiator Grille And Front End Ornamentation
- Position: Front
Fits the following Buick Models:
- Regal | 1984-1987 | Base, GNX, Grand National, Limited, T-Type | 6 Cyl 3.8 L GAS, 6 Cyl 4.1 L GAS, 6 Cyl 4.3 L DIESEL, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL

| Page 1 of 10 |Next >

1-20 of 198 Results

Buick Emblem

Choose OEM Emblem, you're making the optimal decision for superior quality and perfect performance. You can feel confident because each component goes through stringent quality checks. Every part is carefully built to comply with Buick's factory specifications. You'll enjoy a smooth, worry-free installation that fits just right. At ChevyPartsDeal.com, you'll find it easy to get top-quality OEM Buick Emblem. You can shop at highly competitive prices and protect your budget. All our genuine Buick parts include a dependable manufacturer's warranty. You'll also appreciate our straightforward return policy and swift delivery services for extra convenience.

Buick Emblem creates an impression of trust and performance that everyone will instantly know that the car is business. Over a hundred years, Buick has been pursuing a silent ride that bumps off irregular highways and cabinets a serene tranquility. The company overlaid silent tuning, driver-minded technology, and now the aggressive Wildcat EV concept onto a history dating back to 1903 and continuing to adapt to the present life. Customers appreciate its mellow comfort and dependable punch; the cars are neither floaty nor rough, but are ideal in day-to-day commutes and long journeys. The drivers also have confidence in good safety ratings and simple functions that do not involve gimmicks and leave them free to concentrate on the road and the passengers. The Emblem is applied on the hood, trunk, and on the grille of every Buick to enable anyone to trace the lineage within a few seconds. The Emblem is based on hard chrome and baked enamel that resists chips, UV decadence, and road salt, maintaining colors sharp even after decades of winter and washing. Its tri-shield design also doubles up as a high-contrast target which ensures pedestrians and other drivers can recognize the car at a faster rate, and this is an additional wink to safety without additional sensors. Fast mounting points and common mounting sizes result in the easy interchangeability of the part throughout the range, reducing downtime and allowing owners to change the look without much ado.

Buick Emblem Parts and Q&A

Nameplate, Front
10247466
Q: How to Replace or Repair a Door Emblem on Buick Regal?
A:
Before installation of the Regal door emblem/nameplate one must tape the mounting area and create alignment marks using additional tape. Heat the emblem/nameplate using the Heat Gun (J 25070) for thirty seconds by applying circular movement. A flat plastic tool should be used to remove or lift the emblem/nameplate because it protects the paint on panel surfaces. Clean the panel together with adhesive surface using adhesive cleaner and a lint-free clean cloth when tape stays intact on the molding. The replacement of the tape material should be done when damage occurs. Insert the foam tape to the emblem's back side before placing it on the substrate. The 3M(TM) Scotch Brite molding adhesive remover disk (3M(TM) P/N 07502) serves to remove adhesive on body panels, but plastic panels require Varnish Makers and Painters (VMP) naphtha or a 50/50 mixture of isopropyl alcohol and water to clean the adhesive. The installation environment must be kept completely dust-free. Apply VMP naphtha or alcohol-water solution to the area using a lint-free cloth before completely drying it. Apply tape markings followed by surface heating to 27-41°C (80-105°F) along with emblem/nameplate temperatures at 29-32°C (85-90°F). Place the emblem/nameplate directly onto the mounting surface where the marks indicate. Then apply regular pressure while ensuring consistent contact to achieve an even bond. After finishing the installation remove all protective tape from the mounting area.
Emblem, Front
25737019
Q: How to replace the front emblem/nameplate on Buick LeSabre?
A:
Before you work on the front emblem/nameplate start by applying tape to its mounting surface. Heat the emblem/nameplate with the J 25070 Heat Gun J 25070 for a circle pattern during 30 seconds. A plastic flat-blade tool removes the emblem/nameplate only from the panel surface. Prepare the mounting area by removing all old adhesive: for metal body panels use 3M(TM) Scotch Brite molding adhesive remover disks (3M(TM) P/N 07502) or equivalent tools; for plastic panels use a lint-free cloth with Varnish Makers and Painters (VMP) naphtha or a water and isopropyl alcohol mix of 50/50. Prepare the fender area by cleaning and drying it before placing the emblem over its hole. Set your J 25070 Heat Gun to 27-41°C and warm the mounting surface until it reaches 27-41°C (80-105°F). Also warm the emblem/nameplate to 29-32°C (85-90°F) before installation. Take the protective liner off the back of the emblem/nameplate without touching its adhesive side. Place it on the fender surface then push hard from all sides to make the seal permanent. Finally, remove the protective tape.