How to replace hard, split, or separated Engine Mount while keeping the engine/transmission in V8 engine on Pontiac Firebird?

If the rubber mounts are hard, split or separated from the metal backing, they will need to be replaced and the operation can be done on the vehicle with the engine/transmission still in situ. On front-mounted engines there exist throughbolt and nut that should be detached, the engine can then be lifted slightly using a hoist or a jack that has a wood block placed on the oil pan. After that, take off the mount and frame bracket assembly out of the crossmember, put the new mount in place, fit the throughbolt and nut, and properly tighten all the bolts to the incidated torque. For the rear mount, remove the crossmember-to-mount bolts, and then jack up the transmission just enough that the bolts can be slid out. After that, take off the mount to transmission bolts then the mount. Place the new mount and lower the trans, align the crossmember-to-mount bolts before final tightening of all the bolts to torque.

Do engine mounts require attention, and how should broken or deteriorated mounts be replaced in four cylinder engine on Pontiac G6?

Engine mounts seldom require attention, but broken or deteriorated mounts should be replaced immediately to prevent damage or wear on driveline components. To check the mounts, raise the vehicle securely on jackstands and position a jack under the engine oil pan with a large block of wood in between. Carefully raise the engine just enough to relieve the weight from the mounts, then inspect them for any cracks, hardening, or separation from the bushing. Check for any relative movement between the mounts and the engine or frame using a large screwdriver or pry bar; if movement is detected, lower the engine and tighten the mount fasteners. For replacement, disconnect the cable from the negative battery terminal, raise the vehicle again, and support it securely. Remove the air filter assembly, then take off the two nuts securing the mount to the engine and the three bolts securing it to the frame before lifting out the mount. Installation follows the reverse order of removal, ensuring to use thread-locking compound on the mount bolts and tightening them securely before reconnecting the battery.

OEM Pontiac Engine Mount

Engine Motor Mount

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

277 Engine Mounts found

View related parts
Pontiac Upper Mount Bracket Part Number: 22651092
$26.89 MSRP: $104.36
You Save: $77.47 (75%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Adapter, Engine Mounting; Oil Filter Adapter; Adapter
- Position: Upper
Fits the following Pontiac Models:
- Sunfire | 1995-2002 | GT, SE | 4 Cyl 2.3 L GAS, 4 Cyl 2.4 L GAS
View related parts
Pontiac Strut Mount Part Number: 22188174
$32.79 MSRP: $100.52
You Save: $67.73 (68%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Strut, Engine Mounting; Engine Mount Torque Strut; Engine Mount Bracket; Engine Torque Strut; Motor Mount
- Replaces: 10152224, 14036331, 14077778, 22112737
Fits the following Pontiac Models:
- 6000 | 1984-1991 | Base, LE, SE, Special Edition, STE | 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 3.1 L GAS, 6 Cyl 4.3 L DIESEL
- Grand Prix | 1990-1991 | LE, SE | 2.3L L4, 4 Cyl 2.3 L GAS
- Phoenix | 1984 | Base, LE | 4 Cyl 2.5 L GAS
- Trans Sport | 1990-1995 | Base | 6 Cyl 3.1 L GAS, 6 Cyl 3.8 L GAS
View More
View related parts
Pontiac Torque Strut Part Number: 22145939
$17.54 MSRP: $50.58
You Save: $33.04 (66%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Strut, Engine Mount Dampening; Engine Mount Torque Strut; Engine Mount Bracket; Engine Torque Strut; Motor Mount; Front Mount; Mount; Strut; Strut, Engine Mounting
- Replaces: 22145938
Fits the following Pontiac Models:
- Grand Am | 1995-1998 | GT, SE | 4 Cyl 2.3 L GAS, 4 Cyl 2.4 L GAS, 6 Cyl 3.1 L GAS
View related parts
Pontiac Mount Bracket Part Number: 12594433
$30.60 MSRP: $61.44
You Save: $30.84 (51%)
ADD TO CART
Product Specifications
- Other Name: Bracket-Engine Mount Strut & Engine Lift; Engine Mount Bracket; Transmission Mount; Motor Mount
- Replaces: 10154776, 12570320
Fits the following Pontiac Models:
- Aztek | 2001-2005 | Base, GT, Rally | 6 Cyl 3.4 L GAS
- Grand Prix | 1997-2003 | SE | 6 Cyl 3.1 L GAS
- Montana | 1999-2006 | Base, SV6 | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS
- Trans Sport | 1997-1998 | Base, Montana | 6 Cyl 3.4 L GAS
View More
View related parts
Pontiac Motor Mount Part Number: 22538729
$32.13 MSRP: $64.51
You Save: $32.38 (51%)
ADD TO CART
Product Specifications
- Other Name: Mount Assembly-Engine; Engine Mount Torque Strut; Engine Mount Bracket
Fits the following Pontiac Models:
- Sunbird | 1991-1994 | GT, LE, LE Value Leader, SE | 6 Cyl 3.1 L GAS
View related parts
Pontiac Motor Mount Part Number: 22188284
$51.94 MSRP: $90.64
You Save: $38.70 (43%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Mount; Engine Mount Torque Strut; Engine Mount Bracket; Engine Mount
- Replaces: 14082803, 17981702, 17989409, 17996145, 22145863, 22146241, 22145879, 22112974
Fits the following Pontiac Models:
- Bonneville | 1986 | Base, Brougham, LE | 6 Cyl 4.3 L GAS
- Grand Prix | 1986-1987 | Base, Brougham, LE | 6 Cyl 4.3 L GAS
- Parisienne | 1985-1986 | Base, Brougham | 6 Cyl 4.3 L GAS
View More
View related parts
Pontiac Motor Mount Part Number: 10448575
$69.62 MSRP: $121.50
You Save: $51.88 (43%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Mount, Engine Mount Dampening; Engine Mount Torque Strut; Engine Mount Bracket
- Replaces: 10340740, 10448574, 17998813, 22178657, 22146466, 22175206, 22113282, 22146018, 10448576
Fits the following Pontiac Models:
- Aztek | 2001-2005 | Base, GT, Rally | 6 Cyl 3.4 L GAS
- Grand Prix | 1988-2008 | Base, GT, GT1, GT2, GTP, LE, Mclaren, SE, STE | 4 Cyl 2.3 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 3.1 L GAS, 6 Cyl 3.8 L GAS
- Montana | 1999-2006 | Base, SV6 | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS
- Trans Sport | 1997-1998 | Base, Montana | 6 Cyl 3.4 L GAS
View More
View related parts
Pontiac Motor Mount Part Number: 22179268
$73.38 MSRP: $128.06
You Save: $54.68 (43%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Mount Assembly-Engine; Engine Mount Bracket
Fits the following Pontiac Models:
- Firebird | 1998-2002 | Formula, Trans Am | 8 Cyl 5.7 L GAS
View related parts
Pontiac Lower Mount Part Number: 25759455
$78.80 MSRP: $137.51
You Save: $58.71 (43%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Mount, Engine Mounting; Engine Mount Bracket; Motor Mount; Mount; Mount, Engine Mount Dampening
- Position: Lower
- Replaces: 25700266, 25700267
Fits the following Pontiac Models:
- Bonneville | 2004-2005 | GXP | 8 Cyl 4.6 L GAS
View related parts
Pontiac Strut Part Number: 10345905
$79.45 MSRP: $138.65
You Save: $59.20 (43%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Strut, Engine Mount Dampening; Engine Mount Torque Strut; Engine Mount Bracket; Engine Torque Strut; Motor Mount; Strut, Engine Mounting
Fits the following Pontiac Models:
- Montana | 2006 | SV6 | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS
View related parts
Pontiac Motor Mount Part Number: 22188497
$96.48 MSRP: $168.36
You Save: $71.88 (43%)
ADD TO CART
Product Specifications
- Other Name: Mount; Engine Mount Torque Strut; Engine Mount Bracket; Engine Mount; Front Mount; Engine Mount Dampening Cushion
- Replaces: 00459021, 14066861, 14039437, 459021, 97102453
Fits the following Pontiac Models:
- Bonneville | 1984-1986 | Base, Brougham, LE | 8 Cyl 5.0 L GAS
- Firebird | 1984-1992 | Base, S/E, Trans Am
- Grand Prix | 1984-1987 | Base, Brougham, LE | 8 Cyl 5.0 L GAS
- Parisienne | 1984-1986 | Base, Brougham | 8 Cyl 5.0 L GAS
- Safari | 1987 | Base | 8 Cyl 5.0 L GAS
View More
View related parts
Pontiac Strut Mount Part Number: 10420009
$45.32 MSRP: $77.17
You Save: $31.85 (42%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Strut, Engine Mount Dampening; Engine Mount Torque Strut; Engine Mount Bracket; Engine Torque Strut; Motor Mount; Strut; Strut, Engine Mounting
Fits the following Pontiac Models:
- Grand Prix | 2005-2008 | GXP | 8 Cyl 5.3 L GAS
View related parts
Pontiac Front Mount Part Number: 10348601
$102.89 MSRP: $176.71
You Save: $73.82 (42%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Mount, Engine Mount Dampening; Engine Mount Bracket; Motor Mount; Mount, Engine Mounting; Engine Mount
- Position: Front
- Replaces: 22188109
Fits the following Pontiac Models:
- Grand Prix | 2005-2008 | GXP | 8 Cyl 5.3 L GAS
View related parts
Pontiac Strut Bracket Part Number: 10274661
$177.35 MSRP: $301.93
You Save: $124.58 (42%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket, Engine Mounting; Engine Torque Strut Mount; Engine Mount Bracket; Motor Mount; Strut Front Bracket; Engine Mount
Fits the following Pontiac Models:
- Aztek | 2001-2005 | Base, GT, Rally | 6 Cyl 3.4 L GAS
- Montana | 1999-2006 | Base, SV6 | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS
- Trans Sport | 1997-1998 | Base, Montana | 6 Cyl 3.4 L GAS
View More
View related parts
Pontiac Transmission Mount Bracket Part Number: 96535476
$34.18 MSRP: $56.31
You Save: $22.13 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket, Transmission Mounting; Transfer Case Mount; Mount, Engine Mounting; Transmission Mount
Fits the following Pontiac Models:
- G3 | 2009-2010 | Base | 4 Cyl 1.6 L GAS
View related parts
Pontiac Motor Mount Part Number: 92276824
$133.34 MSRP: $219.64
You Save: $86.30 (40%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Mount; Engine Mount Bracket; Mount, Engine Mounting
- Replaces: 92213358, 92237649, 92228915, 92420540
Fits the following Pontiac Models:
- G8 | 2008-2009 | Base | 6 Cyl 3.6 L GAS
View related parts
Pontiac Absorber Bracket Part Number: 25791904
$85.42 MSRP: $135.61
You Save: $50.19 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket, Engine Mounting; Engine Mount Torque Strut; Engine Mount Bracket; Motor Mount
Fits the following Pontiac Models:
- G6 | 2006-2007 | GT, GTP | 6 Cyl 3.9 L GAS
View related parts
Pontiac Strut Mount Part Number: 10271462
$205.18 MSRP: $325.75
You Save: $120.57 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket, Engine Mounting; Engine Mount Torque Strut; Engine Torque Strut Mount; Engine Mount Bracket; Motor Mount; Strut Bracket; Lower Bracket; Strut Front Bracket
Fits the following Pontiac Models:
- Grand Prix | 1997-2008 | Base, GT, GT1, GT2, GTP, GXP, SE | 6 Cyl 3.8 L GAS, 8 Cyl 5.3 L GAS
View related parts
Pontiac Motor Mount Part Number: 92271062
$111.01 MSRP: $173.89
You Save: $62.88 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Mount, Engine Mounting; Engine Mount Bracket; Front Mount; Mount; Mount, Engine Mount Dampening
- Replaces: 92227443, 92259641, 92213251, 92253030
Fits the following Pontiac Models:
- G8 | 2008-2009 | Base, GT, GXP | 6 Cyl 3.6 L GAS, 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L GAS
View related parts
Pontiac Transmission Mount Part Number: 25973870
$72.24 MSRP: $113.16
You Save: $40.92 (37%)
Product Specifications
- Other Name: Mount, Transmission Mounting; Engine Mount Bracket; Transfer Case Mount; Motor Mount; Rear Trans Mount; Mount
- Replaces: 15940092, 22731274
Fits the following Pontiac Models:
- G5 | 2007-2009 | Base, GT | 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L GAS

| Page 1 of 14 |Next >

1-20 of 277 Results

Pontiac Engine Mount

Choose OEM Engine Mount, you're making the optimal decision for superior quality and perfect performance. You can feel confident because each component goes through stringent quality checks. Every part is carefully built to comply with Pontiac's factory specifications. You'll enjoy a smooth, worry-free installation that fits just right. At ChevyPartsDeal.com, you'll find it easy to get top-quality OEM Pontiac Engine Mount. You can shop at highly competitive prices and protect your budget. All our genuine Pontiac parts include a dependable manufacturer's warranty. You'll also appreciate our straightforward return policy and swift delivery services for extra convenience.

Pontiac Engine Mount ensures that the engine is stationary and eliminates shake to provide smoother and safer rides. Pontiac based its fame on rough-road feel, reflexes and fashion that avoids the banality. Drivers such as the stance positioning the car between the wide tracks and the encouragement of positive cornering. Ever since 1926 the badge has pursued excitement, perfecting chassis balance, throttle performance, and cockpit planning, making every trip to work more of a sprint than a slog. New features such as electric gauges and bold lines on the body reveal that the company was not intimidated by new concepts. But the attitude brings in a quality of pragmatism, though, that appreciates the value of changing parts, so that ownership is less hurt and more fun. It made fun without any luxury of any kind, and that pure no nonsense was deafeningly honest. The lineup Engine Mounts are made of hard rubber, hydraulic chambers or smart actuators which get hard or soft according to the revs. Pontiac fiddles these mounts to swall clatter it will slip across firewall. Engine Mount grip prevents the block from lunging in the surrounding hardware, chopping the chances of broken hoses or busted wires. When using throttle the Engine Mount absorbs violent torque twisting making the steering calm and occupants comfortable. Drivers experience less shocks, components wear longer, and the engines can make a difference without force. That strike is a reminder of the original Pontiac assurance of sporty style and practicality. The Engine Mount is a crucial component in maintaining the overall performance of the vehicle.

Pontiac Engine Mount Parts and Q&A

Motor Mount
22188497
Q: How to replace hard, split, or separated Engine Mount while keeping the engine/transmission in V8 engine on Pontiac Firebird?
A:
If the rubber mounts are hard, split or separated from the metal backing, they will need to be replaced and the operation can be done on the vehicle with the engine/transmission still in situ. On front-mounted engines there exist throughbolt and nut that should be detached, the engine can then be lifted slightly using a hoist or a jack that has a wood block placed on the oil pan. After that, take off the mount and frame bracket assembly out of the crossmember, put the new mount in place, fit the throughbolt and nut, and properly tighten all the bolts to the incidated torque. For the rear mount, remove the crossmember-to-mount bolts, and then jack up the transmission just enough that the bolts can be slid out. After that, take off the mount to transmission bolts then the mount. Place the new mount and lower the trans, align the crossmember-to-mount bolts before final tightening of all the bolts to torque.
Absorber Bracket
25791904
Q: Do engine mounts require attention, and how should broken or deteriorated mounts be replaced in four cylinder engine on Pontiac G6?
A:
Engine mounts seldom require attention, but broken or deteriorated mounts should be replaced immediately to prevent damage or wear on driveline components. To check the mounts, raise the vehicle securely on jackstands and position a jack under the engine oil pan with a large block of wood in between. Carefully raise the engine just enough to relieve the weight from the mounts, then inspect them for any cracks, hardening, or separation from the bushing. Check for any relative movement between the mounts and the engine or frame using a large screwdriver or pry bar; if movement is detected, lower the engine and tighten the mount fasteners. For replacement, disconnect the cable from the negative battery terminal, raise the vehicle again, and support it securely. Remove the air filter assembly, then take off the two nuts securing the mount to the engine and the three bolts securing it to the frame before lifting out the mount. Installation follows the reverse order of removal, ensuring to use thread-locking compound on the mount bolts and tightening them securely before reconnecting the battery.