How to replace the rear axle shaft on GMC Yukon?

The first stage to replace the rear Axle Shaft requires the driver to lift the vehicle before removing tire and wheel components. The procedure starts with releasing the brake caliper mounting bracket along with the rear Wheel Speed Sensor. Perform the sequence of steps which begins with removing the gasket alongside the rear axle housing cover then continue with the pinion shaft locking bolt. Owners must remove the pinion shaft completely from axles without a locking differential but should only partially remove it from locking differential axles before rotating the case until the pinion shaft contacts the housing. The screwdriver serves to turn the c-lock while it approaches the thrust block alignment configuration and afterward push the Axle Shaft flange toward the differential until the c-lock releases from the Axle Shaft's button where the shaft remains untwisted to maintain proper alignment. The j 2619-01 (slide hammer) alongside the j 45859 (remover/installer) should be used for axle shafts which prove difficult to extract. Insert the Axle Shaft into the rear axle housing while it enters the differential side gear splines properly. To install lock type axles set the c-lock onto the button end of the shaft whereas lock type axles should position the pinion shaft partially out with c-lock flat against the thrust block before insertion into the differential gear. Attach the pinion shaft through its hole until it lines up with the differential case bolt hole before installing a new locking pinion bolt that needs a torque of 36 nm (27 lb ft) for 8.6-inch axle installation or 50 nm (37 lb ft) for 9.5 ld-inch axle tightening. After securing the rear Wheel Speed Sensor reattach the brake caliper mounting bracket then the rear axle housing cover together with its gasket. The last step consists of reattaching the tire along with wheel assembly followed by adding proper lubricant to the rear axle and lowering the vehicle.

OEM GMC Yukon Axle Shaft

Car Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

99 Axle Shafts found

View related parts
GMC Yukon Output Shaft, Front Passenger Side Part Number: 22761721
$126.03 MSRP: $307.50
You Save: $181.47 (60%)
ADD TO CART
Product Specifications
- Other Name: Shaft, Front Axle; Axle Shaft; Inner Shaft
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2012-2014 GMC Yukon | Denali, Denali Hybrid, Hybrid, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.2 L FLEX
View related parts
GMC Yukon Pinion Shaft, Front Passenger Side Part Number: 19121909
$144.69 MSRP: $353.04
You Save: $208.35 (60%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft, Front Axle; Axle Shaft; Inner Shaft; Shaft
- Position: Passenger Side
- Replaces: 15521907
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-2006 GMC Yukon | Base, Denali, GT, SL, SLE, SLT, Sport | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
GMC Yukon Axle Shaft, Rear Part Number: 23199121
$218.28 MSRP: $380.93
You Save: $162.65 (43%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft-Rear Axle; Axle Shafts; Shaft, Rear Axle Drive
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 GMC Yukon | Denali, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
GMC Yukon Axle Shaft, Rear Part Number: 22943112
$313.10 MSRP: $546.35
You Save: $233.25 (43%)
ADD TO CART
Product Specifications
- Other Name: Shaft-Rear Axle; Axle Shafts; Shaft, Rear Axle Drive
- Position: Rear
- Replaces: 15812663
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2013 GMC Yukon | Denali, Denali Hybrid, Hybrid, SLE, SLT | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
GMC Yukon Axle Shaft, Rear Part Number: 22874951
$507.44 MSRP: $885.49
You Save: $378.05 (43%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft-Rear Axle; Axle Shafts; Shaft, Rear Axle Drive
- Position: Rear
- Replaces: 15286380
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2014 GMC Yukon | Denali, Denali Hybrid, Hybrid, SLE, SLT | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
GMC Yukon Output Shaft, Front Passenger Side Part Number: 22876133
$352.05 MSRP: $589.88
You Save: $237.83 (41%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft, Front Axle; Axle Shaft; Inner Shaft; Intermed Shaft
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 GMC Yukon | Denali, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
GMC Yukon Output Shaft, Front Passenger Side Part Number: 19121908
$230.58 MSRP: $366.09
You Save: $135.51 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft, Front Axle; Axle Shaft; Inner Shaft; Shaft
- Position: Passenger Side
- Replaces: 12479219, 15588366, 15801502
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-2020 GMC Yukon | Base, Denali, Denali Hybrid, GT, Hybrid, SL, SLE, SLT, Sport | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
GMC Yukon Output Shaft, Front Driver Side Part Number: 22876135
$474.41 MSRP: $762.45
You Save: $288.04 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft, Front Axle; Axle Shaft; Inner Shaft; Intermed Shaft; Flange
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 GMC Yukon | Denali, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
GMC Yukon Inner Shaft, Front Part Number: 26033975
$16.83 MSRP: $36.98
You Save: $20.15 (55%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft, Front Drive Axle Shifter/Lock; Axle Shaft; Fork Shaft; Shaft
- Position: Front Inner
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-2004 GMC Yukon | Base, Denali, GT, SL, SLE, SLT, Sport | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
GMC Yukon Axle Shaft, Front Part Number: 7849332
$46.86 MSRP: $88.00
You Save: $41.14 (47%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft-Front Axle; Shaft; Shaft, Front Axle
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1997 GMC Yukon | Base, GT, SL, SLE, SLT, Sport | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
GMC Yukon Companion Flange Part Number: 88967027
$77.53 MSRP: $121.42
You Save: $43.89 (37%)
Product Specifications
- Other Name: Flange, Propeller Shaft Pinion; Yoke, Propeller Shaft Pinion
- Replaces: 15588336
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-2014 GMC Yukon | Base, Denali, Denali Hybrid, GT, Hybrid, SL, SLE, SLT, Sport | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
GMC Yukon Differential Assembly, Front Part Number: 23312177
$1206.09 MSRP: $1906.26
You Save: $700.17 (37%)
Product Specifications
- Other Name: Axle Assembly-Front; Differential
- Position: Front
- Replaces: 23484389
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 GMC Yukon | Denali, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
GMC Yukon Output Shaft, Front Driver Side Part Number: 22761727
Product Specifications
- Other Name: Shaft, Front Axle; Axle Shaft; Inner Shaft
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2012-2014 GMC Yukon | Denali, Denali Hybrid, Hybrid, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.2 L FLEX
View related parts
GMC Yukon Axle Shaft, Front Passenger Side Part Number: 19153230
Product Specifications
- Other Name: Shaft, Front Axle; Output Shaft; Inner Shaft
- Position: Passenger Side
- Replaces: 12479374
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2006 GMC Yukon | Denali, SL, SLE, SLT | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
GMC Yukon Output Shaft, Front Driver Side Part Number: 26006824
Product Specifications
- Other Name: Shaft, Front Axle; Axle Shaft; Inner Shaft; Outer Shaft
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1997 GMC Yukon | Base, GT, SL, SLE, SLT, Sport | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
GMC Yukon Output Shaft, Front Passenger Side Part Number: 26031836
Product Specifications
- Other Name: Shaft Kit, Front Axle; Axle Shaft; Inner Shaft; Outer Shaft
- Position: Passenger Side
- Replaces: 26009629
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1997 GMC Yukon | Base, GT, SL, SLE, SLT, Sport | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
GMC Yukon Axle Shafts, Rear Part Number: 12471488
Product Specifications
- Other Name: Shaft, Rear Axle Drive; Axle Shaft
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2004 GMC Yukon | Denali, SLE, SLT | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
GMC Yukon Axle Shaft, Rear Passenger Side Part Number: 12471329
Product Specifications
- Other Name: Shaft, Rear Axle Drive; Axle Shafts
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2006 GMC Yukon | Denali, SL, SLE, SLT | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
GMC Yukon Axle Shaft Assembly, Front Part Number: 26069244
Product Specifications
- Other Name: Shaft Kit, Front Wheel Drive; CV Axle Assembly; Axle Shaft; CV Axle; Axle Assembly; Shaft Kit, Front Axle
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2006 GMC Yukon | Denali, SL, SLE, SLT | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
GMC Yukon Differential Assembly, Front Part Number: 23312174
Product Specifications
- Other Name: Axle Assembly-Front; Differential
- Position: Front
- Replaces: 23484385, 20980290, 23186399
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 GMC Yukon | Denali, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS

| Page 1 of 5 |Next >

1-20 of 99 Results

GMC Yukon Axle Shaft

Want to cut long-term maintenance and repair costs? Choose OEM Axle Shaft. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine GMC Yukon parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM GMC Yukon Axle Shaft includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

The Axle Shaft of GMC Yukon vehicles is one of the most important parts of the vehicle transmission system since it transmits power from the differential to the drive wheels to enable independent rotation, which privileged tractions. These steel shafts are of different types, although the basic construction is similar; the Truck/Domestic RWD car axles are solid, while those of the independent suspension vehicles use halfshafts. Suspension is carried by solid axles while the gears include a central differential and axle shafts and halfshafts for transmitting the power from the transaxle to the wheels. Axle shafts may get worn out due to contact with obstacles maybe producing noise and vibration, the seals on the other hand may get worn out leading to loss of lubricant and contamination of brakes. In summary, Axle Shaft has major functional responsibilities such as bearing the vehicle weight, transmitting force and ensuring that wheel is accurately positioned in GMC Yukon cars.

GMC Yukon Axle Shaft Parts and Q&A

Axle Shaft, Rear
22874951
Q: How to replace the rear axle shaft on GMC Yukon?
A:
The first stage to replace the rear Axle Shaft requires the driver to lift the vehicle before removing tire and wheel components. The procedure starts with releasing the brake caliper mounting bracket along with the rear Wheel Speed Sensor. Perform the sequence of steps which begins with removing the gasket alongside the rear axle housing cover then continue with the pinion shaft locking bolt. Owners must remove the pinion shaft completely from axles without a locking differential but should only partially remove it from locking differential axles before rotating the case until the pinion shaft contacts the housing. The screwdriver serves to turn the c-lock while it approaches the thrust block alignment configuration and afterward push the Axle Shaft flange toward the differential until the c-lock releases from the Axle Shaft's button where the shaft remains untwisted to maintain proper alignment. The j 2619-01 (slide hammer) alongside the j 45859 (remover/installer) should be used for axle shafts which prove difficult to extract. Insert the Axle Shaft into the rear axle housing while it enters the differential side gear splines properly. To install lock type axles set the c-lock onto the button end of the shaft whereas lock type axles should position the pinion shaft partially out with c-lock flat against the thrust block before insertion into the differential gear. Attach the pinion shaft through its hole until it lines up with the differential case bolt hole before installing a new locking pinion bolt that needs a torque of 36 nm (27 lb ft) for 8.6-inch axle installation or 50 nm (37 lb ft) for 9.5 ld-inch axle tightening. After securing the rear Wheel Speed Sensor reattach the brake caliper mounting bracket then the rear axle housing cover together with its gasket. The last step consists of reattaching the tire along with wheel assembly followed by adding proper lubricant to the rear axle and lowering the vehicle.