How to replace the steering knuckle in a coil spring suspension system on Chevrolet Tahoe?

The coil spring suspension replacement of a Steering Knuckle requires first lifting and supporting the vehicle and then removing the tire followed by the wheel. A suitable jack should be used to support the lower Control Arm during Wheel Hub and bearing removal. First disconnect the electronic suspension control (ESC) link rod from its sensor before detaching the outer tie rod from the knuckle. First remove the brake hose bracket retaining bolt from the knuckle and then use j 43631 Ball Joint remover with j 45851 Ball Joint separator protector adapters to remove the upper retaining nut which isolates the upper Ball Joint from the Steering Knuckle followed by removing the lower Ball Joint. The mechanic should remove the Steering Knuckle followed by a cleaning step which removes contaminants from the upper and lower ball joints as well as the Tie Rod End while checking the tapered areas of the knuckle. Steering knuckles must be replaced when tapered holes show signs of elongation or out-of-roundness or damage. Lay the Steering Knuckle into position then attach the lower Ball Joint next and finish with the retaining nut tightened to 100 nm (74 ft. Lbs.). The upper Ball Joint requires installation on the Steering Knuckle before implementing its retaining nut which should get tightened to 50 nm (37 ft. Lbs.). The brake hose bracket retaining bolt fits onto the knuckle and receives a torque of 9 nm (80 inch lbs.). Now secure the outer tie rod into position on the Steering Knuckle and the Wheel Hub and bearing assembly. Attach esc link rod to sensor before installing tire and wheel and removing vehicle stands before lowering the car.

How to Service and Repair the Steering Knuckle on a Chevrolet Tahoe?

Begin Steering Knuckle replacement by lifting the vehicle to support it then proceed with tire and wheel removal. Start by removing the wheel drive shaft when equipment includes it followed by the Wheel Bearing and hub assembly. Following the removal of the outer Tie Rod End from the knuckle, personnel must detach the upper Control Arm and lower Control Arm from the knuckle before they can remove the knuckle. Lower Ball Joint mounts into the knuckle first and upper Ball Joint goes in next for assembly. Begin by reattaching the outer Tie Rod End; after that install the Wheel Bearing and hub assembly and the wheel drive shaft if present. Reinstall the tire and wheel followed by support removal and lowering the vehicle until you check the wheel alignment.

OEM Chevrolet Tahoe Steering Knuckle

Front Steering Knuckle

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

24 Steering Knuckles found

View related parts
Chevrolet Tahoe Knuckle, Driver Side Part Number: 23242659
$292.32 MSRP: $497.68
You Save: $205.36 (42%)
ADD TO CART
Product Specifications
- Other Name: Knuckle, Steering
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2019-2020 Chevrolet Tahoe | PPV | 8 Cyl 5.3 L FLEX
View related parts
Chevrolet Tahoe Knuckle, Passenger Side Part Number: 23242660
$258.59 MSRP: $410.57
You Save: $151.98 (38%)
ADD TO CART
Product Specifications
- Other Name: Knuckle, Steering
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 Chevrolet Tahoe | LS, LT, LTZ, PPV, Premier, SSV | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Knuckle, Driver Side Part Number: 22842314
$88.71 MSRP: $152.35
You Save: $63.64 (42%)
ADD TO CART
Product Specifications
- Other Name: Knuckle, Steering
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 Chevrolet Tahoe | LS, LT, LTZ, PPV, Premier, SSV | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Knuckle, Passenger Side Part Number: 22842315
$88.71 MSRP: $152.35
You Save: $63.64 (42%)
ADD TO CART
Product Specifications
- Other Name: Knuckle, Steering
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 Chevrolet Tahoe | LS, LT, LTZ, PPV, Premier, SSV | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Knuckle, Driver Side Part Number: 22912208
$306.71 MSRP: $490.06
You Save: $183.35 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle, Steering
- Position: Driver Side
- Replaces: 15942236, 15125944
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2014 Chevrolet Tahoe | Hybrid, LS, LT, LTZ, PPV, SSV | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Knuckle, Rear Passenger Side Part Number: 85116618
$103.10 MSRP: $177.09
You Save: $73.99 (42%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle, Rear Wheel
- Position: Rear Passenger Side
- Replaced by: 85562433
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2023 Chevrolet Tahoe | Commercial, High Country, LS, LT, PPV, Premier, RST, SSV, Z71 | 6 Cyl 3.0 L DIESEL, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Knuckle, Rear Driver Side Part Number: 85116617
$108.48 MSRP: $184.70
You Save: $76.22 (42%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle, Rear Wheel
- Position: Rear Driver Side
- Replaced by: 85562432
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2023 Chevrolet Tahoe | Commercial, High Country, LS, LT, PPV, Premier, RST, SSV, Z71 | 6 Cyl 3.0 L DIESEL, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Knuckle, Driver Side Part Number: 84673207
$88.20 MSRP: $150.15
You Save: $61.95 (42%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Knuckle, Steering
- Position: Driver Side
- Replaces: 84453668
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2023 Chevrolet Tahoe | Commercial, High Country, LS, LT, PPV, Premier, RST, SSV, Z71 | 6 Cyl 3.0 L DIESEL, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Knuckle, Passenger Side Part Number: 18060572
Product Specifications
- Other Name: Knuckle Assembly, Steering; Knuckle, Steering
- Position: Passenger Side
- Replaces: 15981174
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1996 Chevrolet Tahoe | Base, LS, LT | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
Chevrolet Tahoe Knuckle, Passenger Side Part Number: 19257047
Product Specifications
- Other Name: Knuckle, Steering
- Position: Passenger Side
- Replaces: 18048229, 18060556
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2006 Chevrolet Tahoe | Base, LS, LT, Z71 | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Tahoe Knuckle, Driver Side Part Number: 22760659
Product Specifications
- Other Name: Knuckle, Steering
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 Chevrolet Tahoe | LS, LT, LTZ, PPV, Premier, SSV | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Knuckle, Passenger Side Part Number: 22760658
Product Specifications
- Other Name: Knuckle, Steering
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2019 Chevrolet Tahoe | PPV | 8 Cyl 5.3 L FLEX
View related parts
Chevrolet Tahoe Knuckle, Driver Side Part Number: 18060569
Product Specifications
- Other Name: Knuckle, Steering
- Position: Driver Side
- Replaces: 15975273
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-2000 Chevrolet Tahoe | Base, Limited, LS, LT, Z71 | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
Chevrolet Tahoe Knuckle, Passenger Side Part Number: 22912209
Product Specifications
- Other Name: Knuckle, Steering
- Position: Passenger Side
- Replaces: 15125945, 15942237
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2014 Chevrolet Tahoe | Hybrid, LS, LT, LTZ, PPV, SSV | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Knuckle, Passenger Side Part Number: 18060574
Product Specifications
- Other Name: Knuckle Assembly, Steering; Knuckle, Steering
- Position: Passenger Side
- Replaces: 15981299
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-2000 Chevrolet Tahoe | Base, Limited, LS, LT, Z71 | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
Chevrolet Tahoe Knuckle, Driver Side Part Number: 18060571
Product Specifications
- Other Name: Knuckle Assembly, Steering; Knuckle, Steering
- Position: Driver Side
- Replaces: 15981173
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1996 Chevrolet Tahoe | Base, LS, LT | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
Chevrolet Tahoe Knuckle, Passenger Side Part Number: 18060568
Product Specifications
- Other Name: Knuckle, Steering
- Position: Passenger Side
- Replaces: 15975272
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1999 Chevrolet Tahoe | Base, LS, LT | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
Chevrolet Tahoe Knuckle, Driver Side Part Number: 18060567
Product Specifications
- Other Name: Knuckle, Steering
- Position: Driver Side
- Replaces: 15975271
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1999 Chevrolet Tahoe | Base, LS, LT | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
Chevrolet Tahoe Knuckle Part Number: 15739982
Product Specifications
- Other Name: Knuckle Assembly-Steering; Knuckle, Steering
- Replaces: 15956779
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1999 Chevrolet Tahoe | Base, LS, LT | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
Chevrolet Tahoe Knuckle, Passenger Side Part Number: 84673210
$95.86 MSRP: $150.15
You Save: $54.29 (37%)
Product Specifications
- Other Name: Knuckle, Steering
- Position: Passenger Side
- Replaces: 84453669
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2023 Chevrolet Tahoe | Commercial, High Country, LS, LT, PPV, Premier, RST, SSV, Z71 | 6 Cyl 3.0 L DIESEL, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS

| Page 1 of 2 |Next >

1-20 of 24 Results

Chevrolet Tahoe Steering Knuckle

Want to cut long-term maintenance and repair costs? Choose OEM Steering Knuckle. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Tahoe parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Tahoe Steering Knuckle includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

Chevrolet Tahoe Steering Knuckle is an important link between the suspension and steering systems and the front wheels. Its main role is to afford locations for the control arms, tie-rod ends and the wheel and hub or spindle assembly so as to allow vertical movement due to the suspension and horizontal movement due to the operation of the steering. Coil housings on different Chevrolet Tahoe years differ: depending on if the vehicle has rear-wheel drive (RWD) or front, all-wheel, four-wheel drive (FWD/AWD/4WD) the steering knuckle changes. RWD models may have the integral spindle whilst FWD/AWD/4WD models may have a drive axle that runs through the knuckle and fastened to a bolted or pressed hub. The design provides stability and control to its users by facilitating free rotation of wheels coupled with response to the events of operating the vehicle. Rotational checks are crucial for the integrity of the steering knuckle, especially after the exchange of some suspension parts.

Chevrolet Tahoe Steering Knuckle Parts and Q&A

Knuckle, Passenger Side
19257047
Q: How to replace the steering knuckle in a coil spring suspension system on Chevrolet Tahoe?
A:
The coil spring suspension replacement of a Steering Knuckle requires first lifting and supporting the vehicle and then removing the tire followed by the wheel. A suitable jack should be used to support the lower Control Arm during Wheel Hub and bearing removal. First disconnect the electronic suspension control (ESC) link rod from its sensor before detaching the outer tie rod from the knuckle. First remove the brake hose bracket retaining bolt from the knuckle and then use j 43631 Ball Joint remover with j 45851 Ball Joint separator protector adapters to remove the upper retaining nut which isolates the upper Ball Joint from the Steering Knuckle followed by removing the lower Ball Joint. The mechanic should remove the Steering Knuckle followed by a cleaning step which removes contaminants from the upper and lower ball joints as well as the Tie Rod End while checking the tapered areas of the knuckle. Steering knuckles must be replaced when tapered holes show signs of elongation or out-of-roundness or damage. Lay the Steering Knuckle into position then attach the lower Ball Joint next and finish with the retaining nut tightened to 100 nm (74 ft. Lbs.). The upper Ball Joint requires installation on the Steering Knuckle before implementing its retaining nut which should get tightened to 50 nm (37 ft. Lbs.). The brake hose bracket retaining bolt fits onto the knuckle and receives a torque of 9 nm (80 inch lbs.). Now secure the outer tie rod into position on the Steering Knuckle and the Wheel Hub and bearing assembly. Attach esc link rod to sensor before installing tire and wheel and removing vehicle stands before lowering the car.
Knuckle, Passenger Side
22912209
Q: How to Service and Repair the Steering Knuckle on a Chevrolet Tahoe?
A:
Begin Steering Knuckle replacement by lifting the vehicle to support it then proceed with tire and wheel removal. Start by removing the wheel drive shaft when equipment includes it followed by the Wheel Bearing and hub assembly. Following the removal of the outer Tie Rod End from the knuckle, personnel must detach the upper Control Arm and lower Control Arm from the knuckle before they can remove the knuckle. Lower Ball Joint mounts into the knuckle first and upper Ball Joint goes in next for assembly. Begin by reattaching the outer Tie Rod End; after that install the Wheel Bearing and hub assembly and the wheel drive shaft if present. Reinstall the tire and wheel followed by support removal and lowering the vehicle until you check the wheel alignment.