How to service the upper ball joint on Chevrolet Tahoe?

Initial vehicle lifting and supporting are required to service the upper Ball Joint. Take out the tire and wheel first then disconnect the upper Control Arm from the vehicle. The upper Ball Joint needs to be taken out using a Ball Joint press tool. The new Ball Joint needs to fit with the flat edges or notches located just like the old Ball Joint to avoid damage when installing. Move the pressed installation tool inside to place the upper Ball Joint correctly followed by reattachment of the upper Control Arm and tire and wheel assembly. After installation put the safety stands back before lowering the vehicle. End by checking the wheel alignment against official standards that apply to pickup trucks and utility vehicles with rwd or 4wd.

How to replace the lower control arm ball joint (1500) on Chevrolet Tahoe?

First position the vehicle on jack stands to replace the lower Control Arm Ball Joint in model 1500. Take off the wheel drive shaft only if needed. First secure the knuckle away from its position on the Control Arm before taking out the Steering Knuckle from the car. Strike locking tabs from the Ball Joint body using a hammer chisel and safety tools. Fix the ch 41805 - Ball Joint remover install kit tool onto the lower Control Arm while applying a shallow socket to remove the lower Ball Joint from the Control Arm. When you place the new Ball Joint in the lower Control Arm make sure that teeth for the lock tabs are in their upward position on adapter ch-49240-2. Install the Ball Joint with a shallow socket from the ch 41805 - Ball Joint crimper and install kit and tighten the components using adapter ch-49240-2 for 250 nm (184 lb ft). Check that all new lock tabs have the same depth before rotating ch 41805 and repeating the installation cycle. Put back the wheel drive shaft and attach the Steering Knuckle into the vehicle if necessary. Complete the installation by placing the lowering Ball Joint stud nut and tightening it first to 50 nm (37 lb ft) then continuing to 95 degrees on the final turn. Lower the vehicle after taking away the installed parts.

OEM Chevrolet Tahoe Ball Joint

Control Arm Joint

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

8 Ball Joints found

View related parts
Chevrolet Tahoe Lower Ball Joint, Front Part Number: 12475478
$103.35 MSRP: $161.18
You Save: $57.83 (36%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Stud Kit, Front Lower Control Arm Ball; Suspension Ball Joint; Ball Joint; Stud Kit, Steering Knuckle Lower Control Arm Pivot
- Position: Front Lower
- Replaces: 12472819
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2006 Chevrolet Tahoe | Base, LS, LT, Z71 | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Tahoe Lower Ball Joint, Front Part Number: 19256481
$40.33 MSRP: $66.41
You Save: $26.08 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Stud Kit, Front Lower Control Arm Ball; Suspension Ball Joint; Ball Joint; Stud Kit, Steering Knuckle Lower Control Arm Pivot
- Position: Front Lower
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2014 Chevrolet Tahoe | Hybrid, LS, LT, LTZ, PPV, SSV | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Lower Ball Joint, Front Part Number: 19209396
$67.94 MSRP: $116.69
You Save: $48.75 (42%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Stud Kit, Front Lower Control Arm Ball; Suspension Ball Joint; Ball Joint; Stud Kit, Steering Knuckle Lower Control Arm Pivot
- Position: Front Lower
- Replaces: 15922557
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2016 Chevrolet Tahoe | Hybrid, LS, LT, LTZ, PPV, SSV | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Lower Ball Joint, Front Part Number: 15687079
$44.20 MSRP: $88.75
You Save: $44.55 (51%)
ADD TO CART
Product Specifications
- Other Name: Stud Kit, Front Lower Control Arm Ball; Suspension Ball Joint; Ball Joint; Stud Kit, Steering Knuckle Lower Control Arm Pivot
- Position: Front Lower
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1996 Chevrolet Tahoe | Base, LS, LT | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
Chevrolet Tahoe Lower Ball Joint, Front Part Number: 19416896
$88.06 MSRP: $145.05
You Save: $56.99 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Stud Kit, Front Lower Control Arm Ball; Ball Joint; Stud Kit, Steering Knuckle Lower Control Arm Pivot; Stud Kit, Front Wheel Lower Control Arm
- Position: Front Lower
- Replaces: 12480852, 15659724
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-2000 Chevrolet Tahoe | Base, Limited, LS, LT, Z71 | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
Chevrolet Tahoe Upper Ball Joint Part Number: 19146901
Product Specifications
- Other Name: Hose, Power Steering Gear Inlet; Ball Joint; Upper Ball Joints; Stud Kit, Steering Knuckle Upper Control Arm
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-2000 Chevrolet Tahoe | Base, Limited, LS, LT, Z71 | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
Chevrolet Tahoe Lower Ball Joint, Front Part Number: 19416898
Product Specifications
- Other Name: Stud Kit, Front Lower Control Arm Ball; Suspension Ball Joint; Ball Joint; Stud Kit, Steering Knuckle Lower Control Arm Pivot
- Position: Front Lower
- Replaces: 12380415, 12383410
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-2000 Chevrolet Tahoe | Base, Limited, LS, LT, Z71 | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
Chevrolet Tahoe Upper Ball Joint, Front Part Number: 19416903
Product Specifications
- Other Name: Stud Kit, Front Upper Control Arm Ball; Ball Joint; Upper Ball Joints; Stud Kit, Steering Knuckle Upper Control Arm
- Position: Front Upper
- Replaces: 15969282, 15659447
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1999 Chevrolet Tahoe | Base, LS, LT | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL

Chevrolet Tahoe Ball Joint

Want to cut long-term maintenance and repair costs? Choose OEM Ball Joint. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Tahoe parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Tahoe Ball Joint includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

The Ball Joint of Chevrolet Tahoe vehicles is an important component of the suspensions system that connects the steering knuckles and the control arm so that they can rotate angularly about the ball joint but cannot translate. They are mainly located in the front suspension as they are encapsulated in a rubber like material hence protection from dirt and enabling the circulation of lubricants. The rubber seals of the ball joints tend to wear out over time and this lets in water which causes some degree of corrosion and greatly programmed wear and tear. If the vehicle if often used on rough terrains and one hears a knocking sound while driving then it is high time to have the ball joints of the Chevrolet Tahoe changed to provide safe driving facilities.

Chevrolet Tahoe Ball Joint Parts and Q&A

Lower Ball Joint, Front
12475478
Q: How to service the upper ball joint on Chevrolet Tahoe?
A:
Initial vehicle lifting and supporting are required to service the upper Ball Joint. Take out the tire and wheel first then disconnect the upper Control Arm from the vehicle. The upper Ball Joint needs to be taken out using a Ball Joint press tool. The new Ball Joint needs to fit with the flat edges or notches located just like the old Ball Joint to avoid damage when installing. Move the pressed installation tool inside to place the upper Ball Joint correctly followed by reattachment of the upper Control Arm and tire and wheel assembly. After installation put the safety stands back before lowering the vehicle. End by checking the wheel alignment against official standards that apply to pickup trucks and utility vehicles with rwd or 4wd.
Lower Ball Joint, Front
19209396
Q: How to replace the lower control arm ball joint (1500) on Chevrolet Tahoe?
A:
First position the vehicle on jack stands to replace the lower Control Arm Ball Joint in model 1500. Take off the wheel drive shaft only if needed. First secure the knuckle away from its position on the Control Arm before taking out the Steering Knuckle from the car. Strike locking tabs from the Ball Joint body using a hammer chisel and safety tools. Fix the ch 41805 - Ball Joint remover install kit tool onto the lower Control Arm while applying a shallow socket to remove the lower Ball Joint from the Control Arm. When you place the new Ball Joint in the lower Control Arm make sure that teeth for the lock tabs are in their upward position on adapter ch-49240-2. Install the Ball Joint with a shallow socket from the ch 41805 - Ball Joint crimper and install kit and tighten the components using adapter ch-49240-2 for 250 nm (184 lb ft). Check that all new lock tabs have the same depth before rotating ch 41805 and repeating the installation cycle. Put back the wheel drive shaft and attach the Steering Knuckle into the vehicle if necessary. Complete the installation by placing the lowering Ball Joint stud nut and tightening it first to 50 nm (37 lb ft) then continuing to 95 degrees on the final turn. Lower the vehicle after taking away the installed parts.