How to replace the Pinion Bearing on a 10.5 Inch Axle on Chevrolet Tahoe?

The procedure for replacing Differential drive pinion gear pinion bearings on 10.5 inch axles starts with vehicle support and raising. Start by removing the Differential assembly followed by disassembly of the pinion yoke together with the oil seal. The next step should be to eliminate the drive pinion housing assembly. A press machine and suitable tool will help users remove the drive pinion gear pinion along with the collapsible spacer. Using the j 22912-b (Bearing Remover) and a hydraulic press you must remove the inner drive Pinion Bearing which requires a brass drift for performing an even work on bearing cups. The same sequence should be used to remove the outer and inner Pinion Bearing cups and the pinion gear pilot bearing. Installation of the drive pinion gear pilot bearing starts by placing it inside the Differential housing then using the j 22761 (Side Bearing Installer) and j 8092 (Universal Driver Handle) tools for insertion. After fitting the j 37624 (Pinion Bearing Installer) with the j 8092 (Universal Driver Handle) install the inner Pinion Bearing cup. Proceed to install the outer Pinion Bearing cup using the j 8608 (Pinion Bearing Cup Installer) also with the j 8092. The installation of the deficient inner Pinion Bearing uses the j 24433 (Pinion Bearing Installer) combined with a hydraulic press and requires the new collapsible spacer installed afterwards. The pinion bearings should receive axle lubricant before the outer Pinion Bearing gets installed into the retainer. After installing the new pinion oil seal through the j 44414 tool you should place the pinion into the bearing retainer and the drive pinion flange/yoke. Insert an original shim of 0.41 mm (0.016 in) size, unless the original shim is not available, to attach the pinion gear bearing retainer onto the axle housing. For used bearings check the pinion rotating torque between 10-20 lb in (1.0-2.3 Nm) and for new bearings check between 15-30 lb in (1.7-3.4 Nm). The device j 8614-01 (Flange Holder and Remover) helps to achieve specified torque values by regular pinion nut tightening whenever measurements fall below established limits. Check the pinion rotation to verify the bearings seated position before checking and adjusting the torque measurement once more. The last step includes reversion of the Differential assembly followed by adjusting the Differential side bearing preload and drive pinion gear pinion depth along with backlash settings then filling the axle with lubricant and removing support to lower the vehicle.

What tools are required to service and repair the drive pinion bearings for a 9.75 inch axle on Chevrolet Tahoe?

To service and repair the drive pinion bearings for a 9.75 inch axle, the following tools are required: j 22536 pinion driver (J 22536), j 22912-01 split-plate bearing puller (J 22912-01), j 42176 universal driver handle - non-threaded (J 42176), j 45703 Pinion Bearing race remover - dana 248 (J 45703), j 45704 Pinion Bearing race installer - dana 248 (J 45704), j 45705 Pinion Bearing race remover - dana 243/267 (J 45705), j 7818 inner bearing race installer (J 7818), and j 8092 universal drive handle - 3/4 in - 10 (J 8092). Start by elevating the vehicle then detach the Differential assembly and pinion yoke with the pinion oil seal followed by the thrust washer. You should place the j 22536 pinion driver at the base of the pinion before using the j 22536 with a hammer to drive out the pinion while continuously watching for it to escape the rear axle housing. The j 45703 and j 42176 tools extract first the pinion preload shims and inner Pinion Bearing cup and oil deflector; the outer Pinion Bearing cup removal requires the j 45705 and j 42176. A hydraulic press working with the j 22912-01 tool enables inner Pinion Bearing extraction after which you can remove the pinion position shim. To carry out installation begin by placing the oil deflector inside the inner pinion cup bore before installing the cup with j 45704 and j 8092. Use j 7818 and j 8092 for outer Pinion Bearing cup installation. Establish the optimum thicknesses for pinion position shim and pinion preload shim of the drive pinion before reinstalling the Differential assembly and distributing appropriate lubricant into the axle and lowering the vehicle.

OEM Chevrolet Tahoe Pinion Bearing

Transmission Pinion Bearing

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

24 Pinion Bearings found

View related parts
Chevrolet Tahoe Side Bearings Part Number: 88943839
$48.83 MSRP: $144.56
You Save: $95.73 (67%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Side Gear; Differential Bearing
- Replaces: 26091723
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2005 Chevrolet Tahoe | LS, LT, Z71 | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Tahoe Pinion Bearings Part Number: 454021
$161.60 MSRP: $292.48
You Save: $130.88 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing Assembly, Differential Drive Pinion Gear; Differential Pinion Bearing; Rear Pinion Bearing; Inner Pinion Bearing; Differential Drive Pinion; Rear Wheel Bearing.
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2006, 1995-1999 Chevrolet Tahoe | Base, LS, LT, Z71 | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
Chevrolet Tahoe Wheel Bearing Part Number: 9436881
$57.71 MSRP: $145.36
You Save: $87.65 (61%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential; Differential Pinion Bearing; Differential Bearing; Axle Bearings; Shaft; Inner; Side; Differential Gear; Front Wheel; Rear Wheel; Nut.
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-2006 Chevrolet Tahoe | Base, Limited, LS, LT, Z71 | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
Chevrolet Tahoe Pinion Bearings, Inner Part Number: 25824251
$87.27 MSRP: $170.86
You Save: $83.59 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Drive Pinion Gear Inner; Differential Pinion Bearing; Side Bearings; Bearing, Drive Pinion Rear And Intermediate
- Position: Inner
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009-2014 Chevrolet Tahoe | Hybrid, LS, LT, LTZ, PPV, SSV | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L FLEX
View related parts
Chevrolet Tahoe Pinion Bearings, Rear Part Number: 22943106
$71.56 MSRP: $138.90
You Save: $67.34 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Drive Pinion Rear And Intermediate; Differential Pinion Bearing
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 Chevrolet Tahoe | LS, LT, LTZ, PPV, Premier, SSV | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Pinion Bearings Part Number: 23243839
$56.88 MSRP: $110.40
You Save: $53.52 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Pinion; Differential Pinion Bearing; Rear Pinion Bearing; Front/Inner/Outer Pinion; Diff/Drive Axle; Pinion/Clutch/Rear Wheel
- Position: Front
- Replaces: 09418357, 26053758, 9418357, 15286375, 20997052, 22786621, 9418356, 09418356, 12479221
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-2020 Chevrolet Tahoe | Base, Hybrid, LS, LT, LTZ, Limited, PPV, Premier, SSV, Z71 | 4.8L V8, 5.3L V8, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
Chevrolet Tahoe Pinion Bearings Part Number: 9413427
$56.84 MSRP: $109.76
You Save: $52.92 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Drive Pinion Gear Outer; Differential Pinion Bearing; Rear, Front, Outer Pinion Bearings; Differential Drive, Steering Knuckle King, Pinion Shaft, Front Axle Bearings.
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2020 Chevrolet Tahoe | Base, Hybrid, Limited, LS, LT, LTZ, PPV, Premier, SSV, Z71 | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Side Bearings Part Number: 11505123
$51.58 MSRP: $152.62
You Save: $101.04 (67%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Side Gear; Differential Pinion Bearing; Differential Bearing; Bearing
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-2013 Chevrolet Tahoe | Base, Limited, LS, LT, LTZ, PPV, SSV, Z71 | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
Chevrolet Tahoe Pinion Seal, Outer Part Number: 25824252
$47.14 MSRP: $92.28
You Save: $45.14 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Drive Pinion Gear Outer; Differential Pinion Bearing; Pinion Bearings; Side Bearings; Bearing; Bearing, Pinion Shaft Front
- Position: Outer
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009-2014 Chevrolet Tahoe | Hybrid, LS, LT, LTZ, PPV, SSV | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L FLEX
View related parts
Chevrolet Tahoe Pinion Bearings, Inner Part Number: 457108
$50.50 MSRP: $154.36
You Save: $103.86 (68%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Drive Pinion Gear Inner; Differential Pinion Bearing; Rear Pinion Bearing; Front Pinion Bearing; Inner Pinion Bearing; Differential Drive Pinion Bearings.
- Position: Inner
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-2013 Chevrolet Tahoe | Base, Limited, LS, LT, LTZ, PPV, SSV, Z71 | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
Chevrolet Tahoe Side Bearings Part Number: 25824250
$65.71 MSRP: $128.64
You Save: $62.93 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Side Gear; Differential Pinion Bearing; Differential Bearing
- Replaces: 09418390, 9418390
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2016 Chevrolet Tahoe | Base, Hybrid, Limited, LS, LT, LTZ, PPV, SSV, Z71 | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Pinion Bearings Part Number: 9413168
$92.60 MSRP: $167.61
You Save: $75.01 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing Assembly-Roller; Differential Pinion Bearing; Rear Pinion Bearing; Front Pinion Bearing; Drive Pinion Bearing Assembly.
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2005 Chevrolet Tahoe | LS, LT, Z71 | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Tahoe Pinion Bearings Part Number: 9414917
$70.11 MSRP: $133.08
You Save: $62.97 (48%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Drive Pinion Gear Inner; Differential Pinion Bearing; Differential Bearing; Rear Pinion Bearing; Drive Pinion Rear; Axle Pinion Shaft; Ring And Pinion; Pinion Shaft Front.
- Position: Inner
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2006 Chevrolet Tahoe | Base, LS, LT, Z71 | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Tahoe Pinion Bearings, Outer Part Number: 15534483
$52.41 MSRP: $94.85
You Save: $42.44 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing Assembly, Differential Drive Pinion Gear Outer; Differential Pinion Bearing; Front Pinion Bearing; Bearing, Differential Pinion; Bearing, Pinion Shaft Front
- Position: Outer
- Replaces: 09440836, 9440836
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2005 Chevrolet Tahoe | LS, LT, Z71 | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Tahoe Pinion Bearings Part Number: 84428299
$24.40 MSRP: $45.81
You Save: $21.41 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Pinion; Differential Pinion Bearing; Front Pinion Bearing
- Position: Front
- Replaced by: 85722137
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2022 Chevrolet Tahoe | Commercial, High Country, LS, LT, PPV, Premier, RST, SSV, Z71 | 6 Cyl 3.0 L DIESEL, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Pinion Bearings, Rear Part Number: 84881466
$63.71 MSRP: $119.64
You Save: $55.93 (47%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Drive Pinion Rear And Intermediate; Differential Pinion Bearing; Differential Bearing
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2022 Chevrolet Tahoe | Commercial, High Country, LS, LT, PPV, Premier, RST, SSV, Z71 | 6 Cyl 3.0 L DIESEL, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Side Bearings Part Number: 22786619
$126.72 MSRP: $245.94
You Save: $119.22 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Side Gear; Differential Bearing
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2017-2020 Chevrolet Tahoe | LS, LT, PPV, Premier, SSV | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Pinion Bearings Part Number: 9417781
$43.86 MSRP: $103.28
You Save: $59.42 (58%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Front Differential Drive Pinion Gear Outer; Differential Pinion Bearing; Rear, Front, Outer Pinion Bearing; Differential Drive Pinion Front, Drive Pinion, Pinion Shaft Front, Front Axle
- Position: Front Outer
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-2013 Chevrolet Tahoe | Base, Limited, LS, LT, LTZ, PPV, SSV, Z71 | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
Chevrolet Tahoe Side Bearings Part Number: 84881469
$55.96 MSRP: $101.28
You Save: $45.32 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential Side Gear; Differential Pinion Bearing; Differential Bearing
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2022 Chevrolet Tahoe | Commercial, High Country, LS, LT, PPV, Premier, RST, SSV, Z71 | 6 Cyl 3.0 L DIESEL, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
View related parts
Chevrolet Tahoe Pinion Bearings, Rear Part Number: 22943107
$57.28 MSRP: $157.48
You Save: $100.20 (64%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Drive Pinion Rear And Intermediate; Differential Pinion Bearing
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2022 Chevrolet Tahoe | Commercial, High Country, LS, LT, LTZ, PPV, Premier, RST, SSV, Z71 | 6 Cyl 3.0 L DIESEL, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS

| Page 1 of 2 |Next >

1-20 of 24 Results

Chevrolet Tahoe Pinion Bearing

Want to cut long-term maintenance and repair costs? Choose OEM Pinion Bearing. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Tahoe parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Tahoe Pinion Bearing includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

The Chevrolet Tahoe Pinion Bearing stands as an essential mechanical component which strengthens both the fuel system and operational reliability of the Chevrolet Tahoe's transmission system. Relevant to smooth power distribution from the driveshaft to the wheels is this bearing which carries the pinion gear in the differential housing. Multiple generations of Chevrolet Tahoe received Pinion Bearings which engineers have designed to advance performance and extend durability throughout their products. The Pinion Bearing requires consistent proper lubrication alongside regular maintenance to stop potential failure since damage to this component will simultaneously affect important drivetrain systems. Owners can choose the Chevrolet Tahoe Pinion Bearing since it works across different Tahoe model generations thus offering versatility for efficiency and safety needs. The Chevrolet car enhances its robust engines through V8 and turbo diesel options so a reliable Pinion Bearing becomes essential to handle these power levels. The Pinion Bearing of the car delivers superior load distribution capabilities while minimizing exterior noises which results in a quieter operation during driving. The car Pinion Bearing represents an exceptional automotive component which advances the automaker model performance and efficiency and safety performance while becoming a trusted SUV solution for consumers.

Chevrolet Tahoe Pinion Bearing Parts and Q&A

Pinion Bearings, Inner
457108
Q: How to replace the Pinion Bearing on a 10.5 Inch Axle on Chevrolet Tahoe?
A:
The procedure for replacing Differential drive pinion gear pinion bearings on 10.5 inch axles starts with vehicle support and raising. Start by removing the Differential assembly followed by disassembly of the pinion yoke together with the oil seal. The next step should be to eliminate the drive pinion housing assembly. A press machine and suitable tool will help users remove the drive pinion gear pinion along with the collapsible spacer. Using the j 22912-b (Bearing Remover) and a hydraulic press you must remove the inner drive Pinion Bearing which requires a brass drift for performing an even work on bearing cups. The same sequence should be used to remove the outer and inner Pinion Bearing cups and the pinion gear pilot bearing. Installation of the drive pinion gear pilot bearing starts by placing it inside the Differential housing then using the j 22761 (Side Bearing Installer) and j 8092 (Universal Driver Handle) tools for insertion. After fitting the j 37624 (Pinion Bearing Installer) with the j 8092 (Universal Driver Handle) install the inner Pinion Bearing cup. Proceed to install the outer Pinion Bearing cup using the j 8608 (Pinion Bearing Cup Installer) also with the j 8092. The installation of the deficient inner Pinion Bearing uses the j 24433 (Pinion Bearing Installer) combined with a hydraulic press and requires the new collapsible spacer installed afterwards. The pinion bearings should receive axle lubricant before the outer Pinion Bearing gets installed into the retainer. After installing the new pinion oil seal through the j 44414 tool you should place the pinion into the bearing retainer and the drive pinion flange/yoke. Insert an original shim of 0.41 mm (0.016 in) size, unless the original shim is not available, to attach the pinion gear bearing retainer onto the axle housing. For used bearings check the pinion rotating torque between 10-20 lb in (1.0-2.3 Nm) and for new bearings check between 15-30 lb in (1.7-3.4 Nm). The device j 8614-01 (Flange Holder and Remover) helps to achieve specified torque values by regular pinion nut tightening whenever measurements fall below established limits. Check the pinion rotation to verify the bearings seated position before checking and adjusting the torque measurement once more. The last step includes reversion of the Differential assembly followed by adjusting the Differential side bearing preload and drive pinion gear pinion depth along with backlash settings then filling the axle with lubricant and removing support to lower the vehicle.
Side Bearings
25824250
Q: What tools are required to service and repair the drive pinion bearings for a 9.75 inch axle on Chevrolet Tahoe?
A:
To service and repair the drive pinion bearings for a 9.75 inch axle, the following tools are required: j 22536 pinion driver (J 22536), j 22912-01 split-plate bearing puller (J 22912-01), j 42176 universal driver handle - non-threaded (J 42176), j 45703 Pinion Bearing race remover - dana 248 (J 45703), j 45704 Pinion Bearing race installer - dana 248 (J 45704), j 45705 Pinion Bearing race remover - dana 243/267 (J 45705), j 7818 inner bearing race installer (J 7818), and j 8092 universal drive handle - 3/4 in - 10 (J 8092). Start by elevating the vehicle then detach the Differential assembly and pinion yoke with the pinion oil seal followed by the thrust washer. You should place the j 22536 pinion driver at the base of the pinion before using the j 22536 with a hammer to drive out the pinion while continuously watching for it to escape the rear axle housing. The j 45703 and j 42176 tools extract first the pinion preload shims and inner Pinion Bearing cup and oil deflector; the outer Pinion Bearing cup removal requires the j 45705 and j 42176. A hydraulic press working with the j 22912-01 tool enables inner Pinion Bearing extraction after which you can remove the pinion position shim. To carry out installation begin by placing the oil deflector inside the inner pinion cup bore before installing the cup with j 45704 and j 8092. Use j 7818 and j 8092 for outer Pinion Bearing cup installation. Establish the optimum thicknesses for pinion position shim and pinion preload shim of the drive pinion before reinstalling the Differential assembly and distributing appropriate lubricant into the axle and lowering the vehicle.