How to replace the front brake calipers on Chevrolet Suburban 1500?

Before the brake caliper replacement step you need to drain 2/3 of the brake fluid from the master cylinder. Lift the vehicle and after that take out tire and wheel unit. Push the caliper piston down into its housing space by applying force from a c-clamp tool. Detach the brake hose from the caliper at the inlet fitting by undoing the bolt. Afterward uninstall the caliper mounting bolts and take the caliper out. Inspect the caliper assembly. Place the caliper at its proper location first before you install its mounting bolts. Secure the caliper guide pin bolts with torque of 108 n.m (80 lb ft). Secure the brake hose to the caliper using the inlet fitting bolt and tighten it to 45 n.m (33 lb ft). Depress the brake pedal and replace the tire wheel set. Lower the car at the end after taking off all safety devices.

How to service and repair the front brake calipers on Chevrolet Suburban 1500?

You must replace all repair kit contents before you start working on the front brake caliper and apply clean brake fluid to rubber parts for better handling. Repairing any hydraulic system items requires bleeding of the brake system after disconnecting them. It is important to put new brake pads into their matching axle set and tighten all ungreased fastener threads at their correct strength values. Complete maintenance steps on a sterile workspace that avoids mineral oil materials. For safe Piston removal direct compressed air into the brake hose inlet while holding the wood block in front of the Piston to protect it. Unscrew the brake caliper bleed screw cap and bleed screw before you take off the Piston boot, Piston seal, and brake caliper boot. Replace the brake caliper housing as needed because the brake caliper bore and Piston seal groove have too much damage. When it comes to brake caliper mounting brackets always replace them when the guide surfaces show serious wear and corrosion. Remove all parts in the repair kit from brake caliper housing before wiping the parts to clean with alcohol and forcing filtered air through the hardware to eliminate all braking surfaces and flow channels. To build the system you should torque the bleed screw to 12 n.m (106 lb in) then attach its cap. Install the Piston seals into their respective grooves after rubbing brake fluid onto their surface stops and bore seal. Twist the seals carefully when placing them inside the brake caliper bores. Apply brake fluid to brake caliper bores and pistons before putting on their parts and boot. Ensure the boot fits well inside both the Piston groove and brake caliper bore groove. Rephrase the process for the opposite Piston before installing the brake caliper into its proper position.

OEM Chevrolet Suburban 1500 Brake Calipers

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

16 Brake Calipers found

View related parts
Chevrolet Suburban 1500 Caliper Part Number: 19331022
$171.88 MSRP: $331.97
You Save: $160.09 (49%)
ADD TO CART
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Rear
- Replaces: 25848001, 18040100
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2009 Chevrolet Suburban 1500 | Base, LS, LT, LTZ, Z71 | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Suburban 1500 Caliper, Rear Driver Side Part Number: 84191288
$136.61 MSRP: $263.52
You Save: $126.91 (49%)
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Rear Brake (W/O Brake Pads & Bracket; Brake Caliper
- Position: Rear Driver Side
- Replaced by: 86785193
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2014 Chevrolet Suburban 1500 | LS, LT, LTZ | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Suburban 1500 Caliper, Rear Passenger Side Part Number: 84191287
$136.73 MSRP: $266.06
You Save: $129.33 (49%)
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Rear Brake (W/O Brake Pads & Bracket; Brake Caliper
- Position: Rear Passenger Side
- Replaced by: 86785192
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2014 Chevrolet Suburban 1500 | LS, LT, LTZ | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Suburban 1500 Caliper Part Number: 19331021
$170.23 MSRP: $328.77
You Save: $158.54 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Rear
- Replaces: 18040101, 25848000
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2009 Chevrolet Suburban 1500 | Base, LS, LT, LTZ, Z71 | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Suburban 1500 Caliper, Front Driver Side Part Number: 84394384
$109.82 MSRP: $213.14
You Save: $103.32 (49%)
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Front Brake (W/O Brake Pads & Bracket; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Driver Side
- Replaced by: 87859910
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2009 Chevrolet Suburban 1500 | Base, LS, LT, LTZ, Z71 | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Suburban 1500 Caliper, Passenger Side Part Number: 85569602
$96.77 MSRP: $187.82
You Save: $91.05 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Front Brake (W/O Brake Pads & Bracket); Caliper, Wheel Brake Cylinder/Caliper
- Position: Passenger Side
- Replaces: 15904195, 23290150, 84828461, 89059121, 23276880, 22842351
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2014 Chevrolet Suburban 1500 | Base, LS, LT, LTZ, Z71 | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Suburban 1500 Caliper, Driver Side Part Number: 85569601
$72.50 MSRP: $140.30
You Save: $67.80 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Front Brake (W/O Brake Pads & Bracket); Caliper, Wheel Brake Cylinder/Caliper
- Position: Driver Side
- Replaces: 15904194, 23276878, 22842352, 84828460, 89059117, 23290149
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2014 Chevrolet Suburban 1500 | Base, LS, LT, LTZ, Z71 | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Suburban 1500 Caliper, Passenger Side Part Number: 84803425
$137.69 MSRP: $256.99
You Save: $119.30 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Front Brake (W/O Brake Pads & Bracket); Caliper, Wheel Brake Cylinder/Caliper
- Position: Passenger Side
- Replaced by: 87859911
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2009 Chevrolet Suburban 1500 | Base, LS, LT, LTZ, Z71 | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Suburban 1500 Caliper, Driver Side Part Number: 18040100
$171.88 MSRP: $331.97
You Save: $160.09 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Driver Side
- Replaced by: 19331022
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2008 Chevrolet Suburban 1500 | Base, LS, LT, LTZ, Z71 | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Suburban 1500 Caliper Part Number: 88967107
Product Specifications
- Other Name: Caliper Assembly, Rear Brake; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006 Chevrolet Suburban 1500 | Base, LS, LT, LTZ, Z71 | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Suburban 1500 Caliper Part Number: 88967106
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006 Chevrolet Suburban 1500 | Base, LS, LT, LTZ, Z71 | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Suburban 1500 Caliper, Passenger Side Part Number: 18043521
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2006 Chevrolet Suburban 1500 | Base, LS, LT, LTZ, Z71 | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Suburban 1500 Caliper, Driver Side Part Number: 18043520
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2006 Chevrolet Suburban 1500 | Base, LS, LT, LTZ, Z71 | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Suburban 1500 Overhaul Kit, Rear Part Number: 18043518
Product Specifications
- Other Name: Caliper Kit, Rear Brake; Brake Caliper Repair Kit; Disc Brake Hardware Kit; Caliper Kit, Wheel Brake Cylinder/Caliper
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2006 Chevrolet Suburban 1500 | Base, LS, LT, LTZ, Z71 | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Suburban 1500 Caliper, Front Driver Side Part Number: 84394391
$190.26 MSRP: $341.26
You Save: $151.00 (45%)
Product Specifications
- Other Name: Caliper Assembly-Front Brake (W/O Brake Pads & Bracket; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Driver Side
- Replaces: 18046219, 25846388
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2005 Chevrolet Suburban 1500 | Base, LS, LT, Z71 | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Suburban 1500 Caliper, Front Passenger Side Part Number: 84394392
$191.64 MSRP: $343.75
You Save: $152.11 (45%)
Product Specifications
- Other Name: Caliper Assembly-Front Brake (W/O Brake Pads & Bracket; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Passenger Side
- Replaces: 25846389, 18046220
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2005 Chevrolet Suburban 1500 | Base, LS, LT, Z71 | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS

Chevrolet Suburban 1500 Brake Calipers

Want to cut long-term maintenance and repair costs? Choose OEM Brake Calipers. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Suburban 1500 parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Suburban 1500 Brake Calipers includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

Chevrolet Suburban 1500 Brake Calipers Parts and Q&A

Caliper
19331021
Q: How to replace the front brake calipers on Chevrolet Suburban 1500?
A:
Before the brake caliper replacement step you need to drain 2/3 of the brake fluid from the master cylinder. Lift the vehicle and after that take out tire and wheel unit. Push the caliper piston down into its housing space by applying force from a c-clamp tool. Detach the brake hose from the caliper at the inlet fitting by undoing the bolt. Afterward uninstall the caliper mounting bolts and take the caliper out. Inspect the caliper assembly. Place the caliper at its proper location first before you install its mounting bolts. Secure the caliper guide pin bolts with torque of 108 n.m (80 lb ft). Secure the brake hose to the caliper using the inlet fitting bolt and tighten it to 45 n.m (33 lb ft). Depress the brake pedal and replace the tire wheel set. Lower the car at the end after taking off all safety devices.
Caliper, Driver Side
18040100
Q: How to service and repair the front brake calipers on Chevrolet Suburban 1500?
A:
You must replace all repair kit contents before you start working on the front brake caliper and apply clean brake fluid to rubber parts for better handling. Repairing any hydraulic system items requires bleeding of the brake system after disconnecting them. It is important to put new Brake Pads into their matching axle set and tighten all ungreased fastener threads at their correct strength values. Complete maintenance steps on a sterile workspace that avoids mineral oil materials. For safe Piston removal direct compressed air into the brake hose inlet while holding the wood block in front of the Piston to protect it. Unscrew the brake caliper bleed screw cap and bleed screw before you take off the Piston boot, Piston seal, and brake caliper boot. Replace the brake caliper housing as needed because the brake caliper bore and Piston seal groove have too much damage. When it comes to brake caliper mounting brackets always replace them when the guide surfaces show serious wear and corrosion. Remove all parts in the repair kit from brake caliper housing before wiping the parts to clean with alcohol and forcing filtered air through the hardware to eliminate all braking surfaces and flow channels. To build the system you should torque the bleed screw to 12 n.m (106 lb in) then attach its cap. Install the Piston seals into their respective grooves after rubbing brake fluid onto their surface stops and bore seal. Twist the seals carefully when placing them inside the brake caliper bores. Apply brake fluid to brake caliper bores and pistons before putting on their parts and boot. Ensure the boot fits well inside both the Piston groove and brake caliper bore groove. Rephrase the process for the opposite Piston before installing the brake caliper into its proper position.