How to replace the camshaft (except RPOs LC9, LMG, LY2, LY5) on GMC Yukon?

To replace the Camshaft (except RPOs LC9, LMG, LY2, LY5) one must begin by removing the radiator support followed by the valve lifters before removing the engine front cover and Starter motor. Install the j 42386-a (Flywheel Holding Tool) so its teeth interlock with the engine Flywheel teeth before using one m10-1.5 x 120 mm and one m10-1.5 x 45 mm bolt to bolt the j 42386-a and secure both bolts at 50 nm (37 lb ft). Use the crankshaft sprocket to rotate until both alignment marks between the cmp actuator and the crankshaft sprocket become perfectly lined up. Disconnect and remove the cmp actuator solenoid valve (234) before removing the cmp actuator (235) as well as the Timing Chain (208). Unscrew the bolts (204) along with the retainer (203) of the Camshaft while watching out for Camshaft bearing damage. Unscrew the Camshaft sprocket bolt through the front bolt hole of the Camshaft and employ the bolt as a tool for cautious Camshaft extraction from the engine. Clean engine oil serves to lubricate the Camshaft journals and bearings before you should use the bolt to handle the Camshaft duringinstallation into the engine block. First tidy the gasket surface of the engine block before installing the Camshaft retainer (203) together with bolts (204). Tighten hex head bolts of the first design to 25 nm (18 lb ft) and torx® head bolts of the second design to 15 nm (11 lb ft). Install en 46330 (Timing Belt Tensioner Retaining Pin) by compressing the Timing Chain tensioner guide while keeping cmp actuator and Timing Chain in proper alignment. The installation of cmp actuator solenoid valve (234) requires light hand tightening before assessing sprocket alignment. The cmp actuator solenoid valve needs first tightening to 65 nm (48 lb ft) then a single pass to a 90-degree angle by using the j 45059 (Angle Meter). During this procedure, remove the en 46330. First remove the j 42386-a and bolts before restating the Starter motor and engine front cover with valve lifters before finishing with the radiator support.

OEM GMC Yukon Camshaft

Cam

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

17 Camshafts found

View related parts
GMC Yukon Camshaft Part Number: 12623066
$249.67 MSRP: $428.73
You Save: $179.06 (42%)
ADD TO CART
Product Specifications
- Other Name: Camshaft, Engine
- Replaces: 12617374
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2010-2014 GMC Yukon | Denali | 8 Cyl 6.2 L FLEX
View related parts
GMC Yukon Camshaft Part Number: 12629512
$367.96 MSRP: $578.96
You Save: $211.00 (37%)
ADD TO CART
Product Specifications
- Other Name: Camshaft, Engine
- Replaced by: 12741466
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 GMC Yukon | Denali, SLT | 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
GMC Yukon Camshaft Part Number: 12619823
$126.81 MSRP: $215.89
You Save: $89.08 (42%)
ADD TO CART
Product Specifications
- Other Name: Camshaft, Engine
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 GMC Yukon | SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
View related parts
GMC Yukon Camshaft Part Number: 12689035
$220.97 MSRP: $532.86
You Save: $311.89 (59%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Camshaft Assembly-Overhead Valve; Camshaft, Engine
- Replaces: 12625437, 12593205
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2009 GMC Yukon | SLE | 8 Cyl 4.8 L GAS
View related parts
GMC Yukon Camshaft Part Number: 12625436
$407.69 MSRP: $700.20
You Save: $292.51 (42%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Camshaft, Engine
- Replaces: 12593207
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2014 GMC Yukon | SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS
View related parts
GMC Yukon Camshaft Part Number: 12612273
$454.92 MSRP: $774.50
You Save: $319.58 (42%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Camshaft, Engine
- Replaces: 12583227
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2008 GMC Yukon | Denali | 8 Cyl 6.2 L GAS
View related parts
GMC Yukon Camshaft Part Number: 12561721
$495.61 MSRP: $816.41
You Save: $320.80 (40%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Camshaft, Engine
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2006 GMC Yukon | Denali | 8 Cyl 6.0 L GAS
View related parts
GMC Yukon Camshaft Part Number: 12583227
$454.92 MSRP: $774.50
You Save: $319.58 (42%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Camshaft, Engine
- Replaced by: 12612273
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007 GMC Yukon | Denali | 8 Cyl 6.2 L GAS
View related parts
GMC Yukon Camshaft Part Number: 55508606
$88.12 MSRP: $145.12
You Save: $57.00 (40%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Camshaft Assembly-Intake; Camshaft, Engine
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2023 GMC Yukon | Denali, Denali Ultimate, SLE, SLT | 6 Cyl 3.0 L DIESEL
View related parts
GMC Yukon Camshaft Part Number: 55508605
$87.59 MSRP: $139.04
You Save: $51.45 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Camshaft, Engine
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2023 GMC Yukon | Denali, Denali Ultimate, SLE, SLT | 6 Cyl 3.0 L DIESEL
View related parts
GMC Yukon Camshaft Part Number: 12711967
$429.34 MSRP: $681.66
You Save: $252.32 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Camshaft Assembly, Overhead Valve; Camshaft, Engine
- Replaces: 12617373, 12623065
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009 GMC Yukon | Denali | 8 Cyl 6.2 L FLEX
View related parts
GMC Yukon Camshaft Part Number: 12664912
$117.39 MSRP: $201.57
You Save: $84.18 (42%)
ADD TO CART
Product Specifications
- Other Name: Camshaft, Engine
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2023 GMC Yukon | AT4, Denali, Denali Ultimate | 8 Cyl 6.2 L GAS
View related parts
GMC Yukon Camshaft Part Number: 12664911
$108.53 MSRP: $186.34
You Save: $77.81 (42%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Camshaft, Engine
- Replaced by: 12723516
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2023 GMC Yukon | AT4, SLE, SLT | 8 Cyl 5.3 L GAS
View related parts
GMC Yukon Camshaft Part Number: 14066308
Product Specifications
- Other Name: Camshaft, Engine
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1997 GMC Yukon | Base, SL, SLE, SLT, Sport | 8 Cyl 6.5 L DIESEL
View related parts
GMC Yukon Camshaft Part Number: 14060651
Product Specifications
- Other Name: Camshaft, Engine
- Replaces: 14088839
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1995 GMC Yukon | Base, GT, SLE, SLT, Sport | 8 Cyl 5.7 L GAS
View related parts
GMC Yukon Camshaft Part Number: 10241264
Product Specifications
- Other Name: Camshaft, Engine
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996-2000 GMC Yukon | Denali, SL, SLE, SLT | 8 Cyl 5.7 L GAS
View related parts
GMC Yukon Camshaft Part Number: 12629698
Product Specifications
- Other Name: Camshaft, Engine
- Replaces: 12612275
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2013 GMC Yukon | Denali Hybrid, Hybrid | 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV)

GMC Yukon Camshaft

Want to cut long-term maintenance and repair costs? Choose OEM Camshaft. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine GMC Yukon parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM GMC Yukon Camshaft includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

Camshaft is used in the GMC Yukon automobiles to control the opening and closing of the intake and exhaust valves used in the process of admitting air to the vehicle's cylinders and expelling wastes gases. OHV, SOHC, and DOHC are the types of camshaft and based on the specific engines, the design of the camshaft is different. Engineered to rotate in synchronization with the crankshaft, the camshaft timing and lift affect engine performance and they are goods to raise horsepower. Duration, LOSE angle, and material also have a significant effect on the camshaft and the vehicle's performance and power output.

GMC Yukon Camshaft Parts and Q&A

Camshaft
12625436
Q: How to replace the camshaft (except RPOs LC9, LMG, LY2, LY5) on GMC Yukon?
A:
To replace the Camshaft (except RPOs LC9, LMG, LY2, LY5) one must begin by removing the radiator support followed by the valve lifters before removing the engine front cover and Starter motor. Install the j 42386-a (Flywheel Holding Tool) so its teeth interlock with the engine Flywheel teeth before using one m10-1.5 x 120 mm and one m10-1.5 x 45 mm bolt to bolt the j 42386-a and secure both bolts at 50 nm (37 lb ft). Use the crankshaft sprocket to rotate until both alignment marks between the cmp actuator and the crankshaft sprocket become perfectly lined up. Disconnect and remove the cmp actuator solenoid valve (234) before removing the cmp actuator (235) as well as the Timing Chain (208). Unscrew the bolts (204) along with the retainer (203) of the Camshaft while watching out for Camshaft bearing damage. Unscrew the Camshaft sprocket bolt through the front bolt hole of the Camshaft and employ the bolt as a tool for cautious Camshaft extraction from the engine. Clean engine oil serves to lubricate the Camshaft journals and bearings before you should use the bolt to handle the Camshaft duringinstallation into the engine block. First tidy the gasket surface of the engine block before installing the Camshaft retainer (203) together with bolts (204). Tighten hex head bolts of the first design to 25 nm (18 lb ft) and torx® head bolts of the second design to 15 nm (11 lb ft). Install en 46330 (Timing Belt Tensioner Retaining Pin) by compressing the Timing Chain tensioner guide while keeping cmp actuator and Timing Chain in proper alignment. The installation of cmp actuator solenoid valve (234) requires light hand tightening before assessing sprocket alignment. The cmp actuator solenoid valve needs first tightening to 65 nm (48 lb ft) then a single pass to a 90-degree angle by using the j 45059 (Angle Meter). During this procedure, remove the en 46330. First remove the j 42386-a and bolts before restating the Starter motor and engine front cover with valve lifters before finishing with the radiator support.