How to replace the ABS Control Module on GMC Sierra 1500?

As a first step, disconnect the negative Battery Cable and raise and support the vehicle before starting replacement of the ABS Control Module. You should clear all surrounding space around the electronic hydraulic control unit (EHCU) to stop abs component contamination. First represent the brake chassis electrical connectors from the ABS Control Module followed by removing its mounting screws which fasten it to the brake pressure modulator valve (BPMV). When removing the ABS Control Module from the bpmv handle it with care to prevent damaging the ABS Control Module through abrasion or prying damage. The bpmv electrical connector needs removal from the ABS Control Module before cleaning the mounting surfaces. The bpmv electrical connector should be connected first followed by the installation of the ABS Control Module onto the bpmv. New screws need tightening to 5 nm (39 inch lbs.) in cross pattern fashion to secure the ABS Control Module. Reestablish all ABS Control Module electrical connectors followed by vehicle lowering and negative Battery Cable reinstallation. You should use the scan tool tire size calibration function to finish the tire size calibration process.

How to replace the ABS Control Module on GMC Acadia?

Begin the process to change the brake pressure modulator valve by setting the ignition switch to off. Start by removing the air cleaner assembly along with disconnecting the electronic brake control module (EBCM) electrical connector through its locking tabs. First disconnect inlet fittings of the brake pipe leading to the master cylinder while installing caps on the fittings and plugging the brake pressure modulator valve (BPMV) inlet ports to stop fluid loss and contamination. The technician will disconnect the front and rear brake pipe fittings of the bpmv outlet port before capping and plugging them. Drive the bpmv out of the vehicle after unfastening its 2 bracket nuts. Begin by removing the 2 bpmv insulator nuts along with washers before carefully lifting the bpmv upwards from the bracket and finally taking out the 2 bpmv insulators while inspecting both for damage and performing replacements when necessary. Check the lower bpmv insulator for damage before replacing it if needed. To install the 2 bpmv insulators place them onto the bpmv while using denatured alcohol as an assembly assistance. The installation of the lower bpmv insulator requires use of denatured alcohol to mount it to the bracket. The bpmv installation to its bracket requires denatured alcohol on the insulators as an assembly aid. Use denatured alcohol to mount the 2 bpmv insulator washers and 2 nuts and tighten them to 8 n.m (71 lb in). Attach the bpmv and bracket assembly onto the frame rail and fasten it with the 2 bpmv bracket nuts brought to 20 n.m (15 lb ft). Seal the rear brake pipe fittings to the bpmv outlet port by tightening them to 17 n.m (13 lb ft) and proceed with tightening front brake pipe fittings to the same torque. The ebcm electrical connector installation should follow the master cylinder inlet brake pipe fitting installation which requires 20 n.m (15 lb ft) torque tightening. A factory-new bpmv contains pre-installed brake fluid in both its circuits which makes base brake bleeding sufficient when the ignition key remains unchanged. The technician must bleed the hydraulic brake system while simultaneously performing the diagnostic system check - vehicle. During diagnosis inspection check the brake pedal sensation to detect any paddling motion which indicates air has accumulated in the primary system thus requiring performing the abs automated bleeding procedure. The last step is to replace the air cleaner assembly.

OEM GMC ABS Control Module

Anti Lock Brake Control Module

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

212 ABS Control Modules found

View related parts
GMC Control Module Part Number: 84662979
$343.27 MSRP: $621.30
You Save: $278.03 (45%)
ADD TO CART
Product Specifications
- Other Name: Module Assembly-Electronic Brake Control (W/Brake Pressure Mode; ABS Control Module; ABS Control Unit; Module, Electronic Brake Control
Fits the following GMC Models:
- Terrain | 2021-2022 | AT4, Denali, SL, SLE, SLT | 4 Cyl 1.5 L GAS
View related parts
GMC Control Module Part Number: 84401914
$129.98 MSRP: $254.48
You Save: $124.50 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Module, Electronic Brake Control; ABS Control Module
- Replaces: 84329995
Fits the following GMC Models:
- Acadia | 2018-2023 | AT4, Denali, SL, SLE, SLT | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.6 L GAS
View related parts
GMC Control Module Part Number: 20927951
Product Specifications
- Other Name: Module, Electronic Brake Control; ABS Control Module; ABS Control Unit
Fits the following GMC Models:
- Sierra 2500 HD | 2011-2012 | Denali, SLE, SLT, WT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.6 L DIESEL
- Sierra 3500 HD | 2011-2012 | Denali, SLE, SLT, WT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
View related parts
GMC Control Module Part Number: 25802685
Product Specifications
- Other Name: Module, Electronic Brake Control; ABS Control Module; ABS Control Unit
- Replaces: 15233172
Fits the following GMC Models:
- Sierra 2500 HD | 2007-2010 | SLE, SLT, WT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
- Sierra 3500 HD | 2007-2010 | SLE, SLT, WT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
View related parts
GMC Control Module Part Number: 22761033
$327.97 MSRP: $588.28
You Save: $260.31 (45%)
Product Specifications
- Other Name: Module, Electronic Brake Control; ABS Control Module; ABS Control Unit
Fits the following GMC Models:
- Yukon XL 2500 | 2012-2013 | SLE, SLT | 8 Cyl 6.0 L FLEX
View related parts
GMC Control Module Part Number: 25912637
Product Specifications
- Other Name: Module Kit-Electronic Brake & Traction Control; ABS Control Module; ABS Control Unit; Module Kit, Electronic Brake Control
- Replaces: 15873309, 25809108
Fits the following GMC Models:
- Sierra 1500 | 2007-2008 | Denali, SL, SLE, SLT, WT | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L GAS
View related parts
GMC ABS Control Unit Part Number: 84078738
Product Specifications
- Other Name: Module, Electronic Brake Control; ABS Control Module
- Replaces: 25909777
Fits the following GMC Models:
- Yukon | 2008 | Hybrid | 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV)
View related parts
GMC Control Module Part Number: 19244907
Product Specifications
- Other Name: Module, Electronic Brake Control; ABS Control Module; Pressure Valve; ABS Control Unit
- Replaces: 88982943, 88982309, 19301633, 19149022, 89040732
Fits the following GMC Models:
- Sierra 1500 | 2003-2004 | Base, SL, SLE, SLT, WT | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
- Sierra 1500 HD | 2003 | SLE, SLT | 8 Cyl 6.0 L GAS
- Yukon | 2003-2004 | Denali, SLE, SLT | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
- Yukon XL 1500 | 2003-2005 | Denali, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
- Yukon XL 2500 | 2003-2005 | SLE, SLT | 8 Cyl 6.0 L GAS, 8 Cyl 8.1 L GAS
View More
View related parts
GMC Control Module Part Number: 19244903
Product Specifications
- Other Name: Module, Electronic Brake Control; ABS Control Module; ABS Control Unit
- Replaces: 19148796, 19301631, 88982937
Fits the following GMC Models:
- Sierra 1500 | 2003-2005 | Base, Denali, Hybrid, SL, SLE, SLT, WT | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
- Sierra 1500 HD | 2005, 2003 | SLE, SLT | 8 Cyl 6.0 L GAS
View related parts
GMC Control Module Part Number: 12478040
Product Specifications
- Other Name: Module Assembly, Electronic Brake Control; ABS Control Module; ABS Control Unit; Module, Electronic Brake Control
Fits the following GMC Models:
- Yukon XL 2500 | 2000-2001 | SLE, SLT | 8 Cyl 6.0 L GAS, 8 Cyl 8.1 L GAS
View related parts
GMC Pressure Valve Part Number: 19417210
Product Specifications
- Other Name: Valve Kit, Brake Pressure Mode; ABS Control Module; Modulator Valve; Valve Kit, Electronic Brake Control
- Replaces: 25801031, 19416856, 25912640
Fits the following GMC Models:
- Yukon | 2008 | Denali, Hybrid, SLE, SLT | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L GAS
- Yukon XL 1500 | 2008 | Denali, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L GAS
- Yukon XL 2500 | 2008 | SLE, SLT | 8 Cyl 6.0 L GAS
View More
View related parts
GMC Control Module Part Number: 19368155
Product Specifications
- Other Name: Module, Electronic Brake Control; ABS Control Module
- Replaces: 15284102
Fits the following GMC Models:
- Savana 3500 | 2005-2007 | Base, LS, LT, SLE | 8 Cyl 4.8 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
View related parts
GMC Control Module Part Number: 19368156
Product Specifications
- Other Name: Module, Electronic Brake Control; ABS Control Module
- Replaces: 15284103
Fits the following GMC Models:
- Savana 3500 | 2005-2007 | Base, LS, LT, SLE | 8 Cyl 4.8 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
View related parts
GMC Control Module Part Number: 89040684
Product Specifications
- Other Name: Module Assembly, Electronic Brake Control; ABS Control Module; Module, Electronic Brake Control
Fits the following GMC Models:
- Sierra 1500 | 2005-2006 | Base, SL, SLE, WT | 8 Cyl 4.8 L GAS
View related parts
GMC Control Module Part Number: 19417942
Product Specifications
- Other Name: Module, Electronic Brake Control; ABS Control Module
- Replaces: 15235057, 15102088, 19370896
Fits the following GMC Models:
- Savana 3500 | 2003-2007 | Base, LS, LT, SLE | 8 Cyl 4.8 L GAS, 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
View related parts
GMC Control Module Part Number: 88983891
Product Specifications
- Other Name: Module Assembly, Electronic Brake Control; ABS Control Module; Module, Electronic Brake Control
- Replaces: 88982316
Fits the following GMC Models:
- Sierra 1500 | 2003-2006 | Base, Denali, Hybrid, SL, SLE, SLT, WT | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
- Sierra 1500 HD | 2005-2006, 2003 | SLE, SLT | 8 Cyl 6.0 L GAS
View related parts
GMC Pressure Valve Part Number: 19417201
Product Specifications
- Other Name: Valve Kit, Brake Pressure Mode; ABS Control Module; Modulator Valve; Valve Kit, Electronic Brake Control
- Replaces: 15905736, 19416847, 15850402
Fits the following GMC Models:
- Yukon | 2007 | Denali, SLE, SLT | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
- Yukon XL 1500 | 2007 | Denali, SLE, SLT | 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L GAS
- Yukon XL 2500 | 2007 | SLE, SLT | 8 Cyl 6.0 L GAS
View More
View related parts
GMC Control Module Part Number: 19244898
Product Specifications
- Other Name: Module, Electronic Brake Control; ABS Control Module; ABS Control Unit
- Replaces: 88982294
Fits the following GMC Models:
- Yukon XL 2500 | 2001-2002 | SLE, SLT | 8 Cyl 6.0 L GAS, 8 Cyl 8.1 L GAS
View related parts
GMC Control Module Part Number: 22761034
$532.77 MSRP: $952.44
You Save: $419.67 (45%)
Product Specifications
- Other Name: Module, Electronic Brake Control; ABS Control Module; ABS Control Unit
- Replaced by: 19435399
Fits the following GMC Models:
- Sierra 2500 HD | 2012-2014 | Denali, SLE, SLT, WT | 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
- Sierra 3500 HD | 2012-2014 | Denali, SLE, SLT, WT | 8 Cyl 6.0 L FLEX, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL
View related parts
GMC Pressure Valve Part Number: 19417208
$1031.70 MSRP: $1858.92
You Save: $827.22 (45%)
Product Specifications
- Other Name: Valve Kit, Brake Pressure Mode; ABS Control Module; Modulator Valve; Valve Kit, Electronic Brake Control
- Replaces: 19416852, 25912639, 25809109, 15873311
Fits the following GMC Models:
- Sierra 1500 | 2007-2008 | Denali, SL, SLE, SLT, WT | 6 Cyl 4.3 L GAS, 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L GAS

| Page 1 of 11 |Next >

1-20 of 212 Results

GMC ABS Control Module

Choose OEM ABS Control Module, you're making the optimal decision for superior quality and perfect performance. You can feel confident because each component goes through stringent quality checks. Every part is carefully built to comply with GMC's factory specifications. You'll enjoy a smooth, worry-free installation that fits just right. At ChevyPartsDeal.com, you'll find it easy to get top-quality OEM GMC ABS Control Module. You can shop at highly competitive prices and protect your budget. All our genuine GMC parts include a dependable manufacturer's warranty. You'll also appreciate our straightforward return policy and swift delivery services for extra convenience.

GMC ABS Control Module ensures that there is no lockup of wheels and enhances confidence in sudden braking. GMC was established more than 100 years earlier and its pickups and SUVs are robust enough to endure brutal loads but gentle enough to be applied in the daily commute. Powerful boxed frames, torquey engines and silent cab interiors demonstrate that the company has the muscle and the comfort in mind. Its MultiPro tailgate folds, unfolds and halts at various positions to allow hauling to be less than hard work. Hitch guidance, surround vision and other standard driver aids are letting anyone park a big rig within an inch or two. Durability testing is strict, not glitzy slogans, and this is what is propelling each model to a long service life that drivers can rely on. New technology is constantly being introduced without compromise to the work-first attitude of the brand. The outcome is cars that are firm on the workplace and reliable on family holidays. The ABS Control Module is at the center of the braking system, which interprets the wheel-speed sensors, pulsating valves as well as directing a high-pressure pump to proportion force to each caliper within milliseconds during panic brakes. The ABS Control Module is also connected to traction and stability mechanisms and it coordinates throttle cuts and selective brake taps to ensure the vehicle follows straight curves on slick roads. It monitors, makes decisions and corrects hundreds of times in a second, transforming the will of the driver into motor control deceleration, which saves rubber and nerves. Solid-state electronics are not affected by shocks and temperature changes, thus the device performs well both when on dusty trails and frozen highways.

GMC ABS Control Module Parts and Q&A

Control Module
19244894
Q: How to replace the ABS Control Module on GMC Sierra 1500?
A:
As a first step, disconnect the negative Battery Cable and raise and support the vehicle before starting replacement of the ABS Control Module. You should clear all surrounding space around the electronic hydraulic control unit (EHCU) to stop abs component contamination. First represent the brake chassis electrical connectors from the ABS Control Module followed by removing its mounting screws which fasten it to the brake pressure modulator valve (BPMV). When removing the ABS Control Module from the bpmv handle it with care to prevent damaging the ABS Control Module through abrasion or prying damage. The bpmv electrical connector needs removal from the ABS Control Module before cleaning the mounting surfaces. The bpmv electrical connector should be connected first followed by the installation of the ABS Control Module onto the bpmv. New screws need tightening to 5 nm (39 inch lbs.) in cross pattern fashion to secure the ABS Control Module. Reestablish all ABS Control Module electrical connectors followed by vehicle lowering and negative Battery Cable reinstallation. You should use the scan tool tire size calibration function to finish the tire size calibration process.
Control Module
25840308
Q: How to replace the ABS Control Module on GMC Acadia?
A:
Begin the process to change the brake pressure modulator valve by setting the ignition switch to off. Start by removing the air cleaner assembly along with disconnecting the electronic brake control module (EBCM) electrical connector through its locking tabs. First disconnect inlet fittings of the brake pipe leading to the master cylinder while installing caps on the fittings and plugging the brake pressure modulator valve (BPMV) inlet ports to stop fluid loss and contamination. The technician will disconnect the front and rear brake pipe fittings of the bpmv outlet port before capping and plugging them. Drive the bpmv out of the vehicle after unfastening its 2 bracket nuts. Begin by removing the 2 bpmv insulator nuts along with washers before carefully lifting the bpmv upwards from the bracket and finally taking out the 2 bpmv insulators while inspecting both for damage and performing replacements when necessary. Check the lower bpmv insulator for damage before replacing it if needed. To install the 2 bpmv insulators place them onto the bpmv while using denatured alcohol as an assembly assistance. The installation of the lower bpmv insulator requires use of denatured alcohol to mount it to the bracket. The bpmv installation to its bracket requires denatured alcohol on the insulators as an assembly aid. Use denatured alcohol to mount the 2 bpmv insulator washers and 2 nuts and tighten them to 8 n.m (71 lb in). Attach the bpmv and bracket assembly onto the frame rail and fasten it with the 2 bpmv bracket nuts brought to 20 n.m (15 lb ft). Seal the rear brake pipe fittings to the bpmv outlet port by tightening them to 17 n.m (13 lb ft) and proceed with tightening front brake pipe fittings to the same torque. The ebcm electrical connector installation should follow the master cylinder inlet brake pipe fitting installation which requires 20 n.m (15 lb ft) torque tightening. A factory-new bpmv contains pre-installed brake fluid in both its circuits which makes base brake bleeding sufficient when the ignition key remains unchanged. The technician must bleed the hydraulic brake system while simultaneously performing the diagnostic system check - vehicle. During diagnosis inspection check the brake pedal sensation to detect any paddling motion which indicates air has accumulated in the primary system thus requiring performing the abs automated bleeding procedure. The last step is to replace the air cleaner assembly.