How to replace the front Rack and Pinion steering gear (EPS) on 2008 Chevrolet Malibu?

To replace the Rack And Pinion (EPS) begin by strapping the Steering Wheel to stop it from rotating because locking the Steering Column protects the sir system. Disengage the steering linkage outer tie rods from steering knuckles and separate the intermediate Steering Shaft from the Rack And Pinion only when the wheels face straight forward. First isolate the Rack And Pinion by eliminating the transmission rear mount bolt then remove all Rack And Pinion bolts together with their nuts and washers. The left front wheel opening requires Rack And Pinion access during removal procedures. Operate the new Rack And Pinion through the left front wheel opening by hand-tightening all bolts before completing the installation with a torque of 70 n.m (52 lb ft) followed by turning them an additional 90 degrees. First tighten the transmission rear mount bolt to 90 n.m (66 lb ft) before installing the intermediate Steering Shaft to the Rack And Pinion followed by connecting the steering linkage outer tie rods to the steering knuckles. To complete the procedure, perform steering front toe adjustments for proper alignment purposes.

OEM 2008 Chevrolet Malibu Rack And Pinion

Steering Rack And Pinion

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

3 Rack And Pinions found

View related parts
2008 Chevrolet Malibu Steering Gear Part Number: 22742144
Product Specifications
- Other Name: Gear Assembly-Steering; Gear Assembly
- Replaced by: 19330576
- Item Weight: 18.40 Pounds
- Item Dimensions: 51.1 x 8.3 x 6.1 inches
- Condition: New
- SKU: 22742144
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2008 Chevrolet Malibu Submodels:
- LS, LT, LTZ, Maxx LS, Maxx LT, Maxx LTZ, Maxx SS, SS | 4 Cyl 2.2 L GAS, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L GAS, 6 Cyl 3.9 L GAS
View related parts
2008 Chevrolet Malibu Steering Gear, Green Line Part Number: 15858369
Product Specifications
- Other Name: Gear Assembly-Steering; Gear Assembly
- Replaces: 15216792
- Item Weight: 17.50 Pounds
- Item Dimensions: 50.2 x 6.5 x 10.8 inches
- Condition: New
- SKU: 15858369
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2008 Chevrolet Malibu Submodels:
- Base, Hybrid, LS, LT, LTZ, Maxx LS, Maxx LT, Maxx LTZ, Maxx SS, SS | 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.4 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS
View related parts
2008 Chevrolet Malibu Steering Gear Part Number: 19303500
Product Specifications
- Other Name: Gear, Steering; Gear Assembly
- Replaces: 15216791, 22687087, 15858368, 25902150, 21998461
- Item Weight: 18.60 Pounds
- Item Dimensions: 53.2 x 6.1 x 8.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19303500
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2008 Chevrolet Malibu Submodels:
- Base, Classic LS, Classic LT, Hybrid, LS, LT, LTZ, Maxx, Maxx LS, Maxx LT, Maxx LTZ, Maxx SS, SS | 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.4 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS

2008 Chevrolet Malibu Rack And Pinion

With a comprehensive array of OEM 2008 Chevrolet Malibu Rack And Pinion, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2008 Chevrolet Malibu Rack And Pinion are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.

2008 Chevrolet Malibu Rack And Pinion Parts and Q&A

Q: How to replace the front Rack and Pinion steering gear (EPS) on 2008 Chevrolet Malibu?
A: To replace the Rack And Pinion (EPS) begin by strapping the Steering Wheel to stop it from rotating because locking the Steering Column protects the sir system. Disengage the steering linkage outer tie rods from steering knuckles and separate the intermediate Steering Shaft from the Rack And Pinion only when the wheels face straight forward. First isolate the Rack And Pinion by eliminating the transmission rear mount bolt then remove all Rack And Pinion bolts together with their nuts and washers. The left front wheel opening requires Rack And Pinion access during removal procedures. Operate the new Rack And Pinion through the left front wheel opening by hand-tightening all bolts before completing the installation with a torque of 70 n.m (52 lb ft) followed by turning them an additional 90 degrees. First tighten the transmission rear mount bolt to 90 n.m (66 lb ft) before installing the intermediate Steering Shaft to the Rack And Pinion followed by connecting the steering linkage outer tie rods to the steering knuckles. To complete the procedure, perform steering front toe adjustments for proper alignment purposes.