How to replace the liftgate emblem/nameplate on 2008 Chevrolet Equinox?

Before putting on the new equinox liftgate emblem/nameplate you need to tape the installation surface and set up alignment markers. Hold a heat gun at about 152 mm (6 inches) from the part and move the heat over the emblem/nameplate for 30 seconds in circular patterns. Insert a plastic scraper under the emblem/nameplate to pry it off from the panel. Use the 3M(TM) scotch brite molding adhesive remover disk (3M(TM) P/N 07501) for body panels and a varnish makers and painters (vmp) naphtha solution or water/isopropyl alcohol mixture for plastic panels to remove all leftover adhesive. Use the identical cleaning solution to wipe the installation site before fully drying it. Use tape to mark the area when there is no specified placement for the emblem. Fix the equinox emblem/nameplate at the top left edge which should measure 11 mm (0.043 inches) from the liftgate and bottom center line must be placed exactly 160 mm (6.30 inches) below it. Install the chevrolet emblem/nameplate 31 mm (1.22 in) from the right liftgate edge with its dimension (b) matching at 160 mm (6.30 in). Use heat to raise the application area temperature between 80-105°F (80-105°F), then prep the emblem/nameplate surface for installation at 85-90°F. Stay away from touching the adhesive coating and pull off the protective material to put the emblem/nameplate at the marked spots by pressing it hard against the surface. Press evenly on all parts of the badge to seal it to the surface before taking off the tape at the rear end.

OEM 2008 Chevrolet Equinox Emblem

Badge

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

8 Emblems found

View related parts
2008 Chevrolet Equinox Emblem, Front Part Number: 15252284
$47.11 MSRP: $70.11
You Save: $23.00 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Emblem, Radiator Grille And Front End Ornamentation
- Position: Front
- Item Weight: 0.60 Pounds
- Item Dimensions: 9.2 x 2.1 x 2.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 15252284
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2008 Chevrolet Equinox Submodels:
- LS, LT, LTZ, Sport | 6 Cyl 3.4 L GAS, 6 Cyl 3.6 L GAS
View related parts
2008 Chevrolet Equinox Nameplate Part Number: 5485714
$20.97 MSRP: $30.01
You Save: $9.04 (31%)
ADD TO CART
Product Specifications
- Other Name: Emblem Assembly-Lift Gate; Emblem,Rear End Panel And Tailgate
- Item Weight: 0.30 Pounds
- Item Dimensions: 4.1 x 16.2 x 0.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5485714
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2008 Chevrolet Equinox Submodels:
- LS, LT, LTZ, Sport | 6 Cyl 3.4 L GAS, 6 Cyl 3.6 L GAS
View related parts
2008 Chevrolet Equinox Nameplate Part Number: 84310387
$25.23 MSRP: $39.49
You Save: $14.26 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Plate Assembly-Lift Gate Transmission Name *Exterior Brim; Plate, End Gate And Rear Door Decoration; Emblem,Rear End Panel And Tailgate; Plate,Rear End Panel And Tailgate
- Replaces: 84176772, 15239124, 84996815, 23463274
- Item Weight: 0.30 Pounds
- Item Dimensions: 4.6 x 2.2 x 0.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 84310387
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2008 Chevrolet Equinox Submodels:
- L, LS, LT, LTZ, Sport | 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 3.4 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
2008 Chevrolet Equinox Nameplate Part Number: 23255003
$27.02 MSRP: $42.29
You Save: $15.27 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Plate Assembly-Lift Gate Vehicle & Trim Level Name *Chrome; Emblem,Rear End Panel And Tailgate; Plate,Rear End Panel And Tailgate
- Replaces: 05482100, 22878313, 25866035, 5482100, 25795263
- Item Weight: 0.30 Pounds
- Item Dimensions: 12.9 x 1.8 x 0.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 23255003
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2008 Chevrolet Equinox Submodels:
- LT | 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 3.4 L GAS, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
2008 Chevrolet Equinox Nameplate, Rear Part Number: 25795262
$25.55 MSRP: $38.02
You Save: $12.47 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Emblem, Rear End Panel And Tailgate; Emblem,Rear End Panel And Tailgate
- Position: Rear
- Replaces: 5482099, 05482099, 25866034
- Item Weight: 0.30 Pounds
- Item Dimensions: 10.7 x 1.6 x 0.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 25795262
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2008 Chevrolet Equinox Submodels:
- LS | 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS, 6 Cyl 3.4 L GAS
View related parts
2008 Chevrolet Equinox Emblem Part Number: 84689784
$11.42 MSRP: $17.00
You Save: $5.58 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Emblem, Front Side Door; Decal; Nameplate; Emblem, Cab, Load Carrier, Rear End, Door, Quarter Panel, Fender, Rocker Panel, Side Step.
- Replaces: 15223483, 15223484
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 84689784
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following 2008 Chevrolet Equinox Submodels:
- LS, LT, LTZ, Sport | 6 Cyl 3.4 L GAS, 6 Cyl 3.6 L GAS
View related parts
2008 Chevrolet Equinox Emblem, Black, Rear Part Number: 15250666
Product Specifications
- Other Name: Emblem, Rear End Panel And Tailgate; Emblem,Rear End Panel And Tailgate
- Position: Rear
- Item Weight: 0.40 Pounds
- Item Dimensions: 5.1 x 4.9 x 11.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 15250666
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2008 Chevrolet Equinox Submodels:
- LS, LT, LTZ, Sport | 6 Cyl 3.4 L GAS, 6 Cyl 3.6 L GAS
View related parts
2008 Chevrolet Equinox Emblem Part Number: 15259143
Product Specifications
- Other Name: Emblem, Radio Auxiliary Speakers
- Position: Rear
- Item Weight: 0.80 Pounds
- Item Dimensions: 2.9 x 1.0 x 0.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 15259143
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2008 Chevrolet Equinox Submodels:
- LS, LT, LTZ, Sport | 6 Cyl 3.4 L GAS, 6 Cyl 3.6 L GAS

2008 Chevrolet Equinox Emblem

With a comprehensive array of OEM 2008 Chevrolet Equinox Emblem, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2008 Chevrolet Equinox Emblem are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.

2008 Chevrolet Equinox Emblem Parts and Q&A

Q: How to replace the liftgate emblem/nameplate on 2008 Chevrolet Equinox?
A: Before putting on the new equinox liftgate emblem/nameplate you need to tape the installation surface and set up alignment markers. Hold a heat gun at about 152 mm (6 inches) from the part and move the heat over the emblem/nameplate for 30 seconds in circular patterns. Insert a plastic scraper under the emblem/nameplate to pry it off from the panel. Use the 3M(TM) scotch brite molding adhesive remover disk (3M(TM) P/N 07501) for body panels and a varnish makers and painters (vmp) naphtha solution or water/isopropyl alcohol mixture for plastic panels to remove all leftover adhesive. Use the identical cleaning solution to wipe the installation site before fully drying it. Use tape to mark the area when there is no specified placement for the emblem. Fix the equinox emblem/nameplate at the top left edge which should measure 11 mm (0.043 inches) from the liftgate and bottom center line must be placed exactly 160 mm (6.30 inches) below it. Install the chevrolet emblem/nameplate 31 mm (1.22 in) from the right liftgate edge with its dimension (b) matching at 160 mm (6.30 in). Use heat to raise the application area temperature between 80-105°F (80-105°F), then prep the emblem/nameplate surface for installation at 85-90°F. Stay away from touching the adhesive coating and pull off the protective material to put the emblem/nameplate at the marked spots by pressing it hard against the surface. Press evenly on all parts of the badge to seal it to the surface before taking off the tape at the rear end.