OEM 2000 GMC Jimmy CV Boot

Axle Boot
  • Select Vehicle by Model
  • Select Vehicle by VIN
Select Vehicle by Model
Make
Model
Year
or
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

2 CV Boots found

  • 2000 GMC Jimmy CV Boot Diagram - 26059671
    View related parts

    2000 GMC Jimmy Boot Kit, Front Part Number: 26059671

    $36.90 MSRP: $57.80
    You Save: $20.90 (37%)
    Product Specifications
    • Other Name: Boot Kit, Front Axle; CV Boot; Outer Boot
    • Position: Front
    • Item Weight: 1.70 Pounds
    • Item Dimensions: 8.0 x 7.0 x 6.8 inches
    • Condition: New
    • Fitment Type: Direct Replacement
    • Require Quantity: 2
    • SKU: 26059671
    • Warranty: This genuine part is guaranteed by GM's factory warranty.
    More Info
    Fits the following 2000 GMC Jimmy Submodels:
    • Diamond Edition, Envoy, SL, SLE, SLS, SLT | 6 Cyl 4.3 L GAS
  • 2000 GMC Jimmy CV Boot Diagram - 26059675
    View related parts
    Product Specifications
    • Other Name: Boot Kit, Front Wheel Drive Axle Shaft; CV Boot; Inner Boot; Boot Kit, Front Axle
    • Position: Front
    • Item Weight: 1.60 Pounds
    • Item Dimensions: 6.8 x 6.2 x 6.2 inches
    • Condition: New
    • Fitment Type: Direct Replacement
    • Require Quantity: 2
    • SKU: 26059675
    • Warranty: This genuine part is guaranteed by GM's factory warranty.
    More Info
    Fits the following 2000 GMC Jimmy Submodels:
    • Diamond Edition, Envoy, SL, SLE, SLS, SLT | 6 Cyl 4.3 L GAS

2000 GMC Jimmy CV Boot

With a comprehensive array of OEM 2000 GMC Jimmy CV Boot, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2000 GMC Jimmy CV Boot are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.

2000 GMC Jimmy CV Boot Parts and Q&A

  • Q: How to replace the outer CV Boot and CV Joint on the wheel drive shaft on 2000 GMC Jimmy?
    A: The following tools must be obtained to replace wheel drive shaft outer joint and boot: you need snap ring pliers (J8059), seal clamp tool (J35910) and swage clamp tool (J41048) with a breaker bar and torque wrench for this job. Snap ring pliers (J8059), seal clamp tool (J35910), swage clamp tool (J41048), a breaker bar , and a torque wrench . Secure the halfshaft inside the vise under protective covers while you remove outer cv joint boot clamp protectors using side cutters to separate the boot clamps from each other. Grind the swage ring while protecting the outer race before using a tool to push the boot toward the retainer and scrape all grease off the cv joint face. Install the snap ring pliers (J8059) to loosely position the halfshaft retaining snap ring before removing the cv joint from the halfshaft. Start by dropping the worn boot before using a brass drift to guide the cage movement until all balls fall out. You can now extract the cage and inner race from the joint. All components of the cv joint should undergo degreasing before a damage check is performed to replace any required parts. Put a thin layer of grease on inner and outer race grooves before sliding the inner race into its cage and making the races match correctly. Apply the brass drift to insert the cage at an angle before reinserting all balls and proceed to fill the joint boot with the ready-measured grease. Secure the new small swage clamp onto the cv joint boot before putting the boot in place on the halfshaft bar. Use the swage clamp tool (J41048) to clamp the boot. Begin by tightening the bolts manually when they are snug to maintain correct placement for the boot and swage clamp housing assembly after which use a torque wrench to fasten the large retaining clamp at 176 nm (130 ft. Lbs.). Inspect the clamp ear gap dimension before adding boot clamp protectors if vehicle components require them.

Related 2000 GMC Jimmy Parts