How to remove and install the crankshaft pulley in 2.2L four cylinder engine on Pontiac Grand Prix?

To undo the component, one must turn off the car and then undo the clamp connector at the negative battery terminal so that the Theftlock audio system cannot lock out the disconnection if installed. After that remove the drivebelt, then lift the front of the vehicle and place it on jackstands in a securely manner, then remove the right front tire and inner fender splash shield. Take out the pulley-to-crankshaft bolt, with a breaker bar, if it is very stiff. If required, remove the lower bell housing cover and using a large screwdriver; place it through the flywheel or driveplate ring gear to stop the crankshaft from coming round when loosening up or doing up the bolt. Subsequently, take out the three bolts fastening the pulley on the hub then use the puller to, For installation, use clean multi purpose grease on the seal contact part of the hub and then place the hub over the crankshaft and slide it on until it gets up against the crankshaft gear with the slot in the hub best fitting the Woodruff key in crankshaft. Fix hub into place using the pulley-to-crankshaft bolt and tighten the bolt to the recommended torque. Last but not the least, the final stages are always marked by the reversal of the entire removal procedure.

How to disconnect the cable from the negative terminal of the battery and remove the crankshaft pulley in 3.5L,3.9L V6 engine on Pontiac G6?

Disconnect the cable from the negative terminal of the battery. With the parking brake applied and the shift lever in Park, loosen the lug nuts from the right front wheel, then raise the front of the vehicle and support it securely on jackstands. Remove the right front wheel and the right splash shield from the wheel well. Remove the drivebelt. Support the right side of the subframe with a floor jack, remove the right-side subframe bolts, and loosen the left-side subframe bolts, then partially lower the right side of the subframe. Remove the bolt from the front of the crankshaft using a pin spanner to prevent the crankshaft from turning while loosening the pulley bolt, which is normally very tight; use a large breaker bar and a six-point socket for removal. Obtain a new bolt but save the old one for the initial installation of the pulley. Use a puller with three hooks that can grasp the inside diameter of the outer ring of the crankshaft pulley, ensuring the hooks do not attach to the outside of the pulley. Remove the crankshaft pulley/balancer from the crankshaft using a puller that bears on the crankshaft pulley hub, and use a spacer to avoid damage to the crankshaft. Apply a small amount of RTV sealant onto the crankshaft keyway and allow it to set up slightly. Position the crankshaft pulley/balancer on the crankshaft and slide it on as far as it will go, ensuring the slot in the hub aligns with the Woodruff key in the end of the crankshaft. Using a crankshaft balancer installation tool, press the crankshaft pulley/balancer onto the crankshaft, noting that the crankshaft bolt can also be used for this purpose with clean engine oil on the bolt threads to prevent galling. For a 2005 model, install the old bolt and washer and tighten it to the specified torque. For a 2006 or later model, purchase a new bolt, install the old bolt and washer, tighten it to the specified torque, then remove it. Install the new bolt and washer, tightening it to the specified torque followed by the angle torque. The remaining installation steps are the reverse of removal, ensuring to tighten the subframe bolts to the specified torque.

OEM Pontiac Crankshaft Pulley

Crankshaft Pulley Engine Harmonic Balancer

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

42 Crankshaft Pulleys found

View related parts
Pontiac Pulley Part Number: 560328
Product Specifications
- Other Name: Pulley Assembly- (3 Groove 7.320 Pd); Pulley, Engine Crankshaft And Camshaft Balancer; Pulley, Fan And Coolant Pump; Pulley, Engine Crankshaft
Fits the following Pontiac Models:
- Bonneville | 1984 | Base, Brougham, LE | 8 Cyl 5.7 L DIESEL
- Grand Prix | 1984 | Base, Brougham, LE | 8 Cyl 5.7 L DIESEL
- Parisienne | 1984-1985 | Base, Brougham | 8 Cyl 5.7 L DIESEL
- Safari | 1987-1989 | Base | 8 Cyl 5.0 L GAS
View More
View related parts
Pontiac Crankshaft Pulley Part Number: 88969562
Product Specifications
- Other Name: Pulley, Engine Crankshaft And Camshaft Balancer; Harmonic Balancer Puller; Pulley
Fits the following Pontiac Models:
- Vibe | 2003-2006 | GT | 4 Cyl 1.8 L GAS
View related parts
Pontiac Crankshaft Pulley Part Number: 19185263
Product Specifications
- Other Name: Pulley, Engine Crankshaft And Camshaft Balancer; Harmonic Balancer Puller; Pulley
Fits the following Pontiac Models:
- Vibe | 2009-2010 | AWD, Base, GT | 4 Cyl 2.4 L GAS
View related parts
Pontiac Fan Clutch Part Number: 14090951
Product Specifications
- Other Name: Pulley, Engine Crankshaft; Crankshaft Pulley; Pulley
Fits the following Pontiac Models:
- T1000 | 1984-1987 | Base | 4 Cyl 1.6 L GAS
View related parts
Pontiac Pulley Part Number: 22505008
Product Specifications
- Other Name: Pulley, Engine Crankshaft
Fits the following Pontiac Models:
- Safari | 1989 | Base | 8 Cyl 5.0 L GAS
View related parts
Pontiac Vibration Damper Part Number: 10032616
Product Specifications
- Other Name: Crankshaft Damper
Fits the following Pontiac Models:
- Fiero | 1985-1986 | GT, SE, Sport | 6 Cyl 2.8 L GAS
View related parts
Pontiac Pulley Part Number: 14033107
Product Specifications
- Other Name: Pulley, Engine Crankshaft And Camshaft Balancer
Fits the following Pontiac Models:
- Firebird | 1984 | Base, S/E | 6 Cyl 2.8 L GAS
View related parts
Pontiac Vibration Damper Part Number: 14082324
Product Specifications
- Other Name: Damper Assembly-Torsional; Harmonic Balancer Hub; Hub; Pulley; Damper; Damper, Engine Crankshaft And Camshaft Balancer; Damper, Engine Crankshaft
Fits the following Pontiac Models:
- Bonneville | 1986 | Base, Brougham, LE | 6 Cyl 4.3 L GAS
- Grand Prix | 1986-1987 | Base, Brougham, LE | 6 Cyl 4.3 L GAS
- Parisienne | 1985-1986 | Base, Brougham | 6 Cyl 4.3 L GAS
View More
View related parts
Pontiac Crankshaft Pulley Part Number: 10027439
Product Specifications
- Other Name: Pulley, Engine Crankshaft And Camshaft Balancer; Harmonic Balancer Puller; Pulley
Fits the following Pontiac Models:
- J2000 Sunbird | 1984-1985 | Base, LE, SE | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS
- Sunbird | 1986 | Base, GT, SE | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS
View related parts
Pontiac Pulley Part Number: 10069912
Product Specifications
- Other Name: Pulley Assembly-Crankshaft; Pulley, Engine Crankshaft And Camshaft Balancer
Fits the following Pontiac Models:
- Bonneville | 1984-1986 | Base, Brougham, LE | 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS
- Grand Prix | 1984-1987 | Base, Brougham, LE | 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS
- Parisienne | 1986 | Base, Brougham | 8 Cyl 5.0 L GAS
View More
View related parts
Pontiac Crankshaft Pulley Part Number: 25522124
Product Specifications
- Other Name: Pulley, Engine Crankshaft And Camshaft Balancer; Harmonic Balancer Puller; Pulley
Fits the following Pontiac Models:
- Grand Am | 1985 | Base, LE | 6 Cyl 3.0 L GAS
View related parts
Pontiac Pulley Part Number: 14088683
Product Specifications
- Other Name: Pulley Assembly-Crankshaft; Pulley, Engine Crankshaft And Camshaft Balancer
Fits the following Pontiac Models:
- Bonneville | 1984-1986 | Base, Brougham, LE | 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS
- Firebird | 1985-1987 | Base, S/E, Trans Am | 8 Cyl 5.0 L GAS
- Grand Prix | 1984-1987 | Base, Brougham, LE | 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS
- Parisienne | 1985-1986 | Base, Brougham | 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS
View More
View related parts
Pontiac Crankshaft Pulley Part Number: 10083143
Product Specifications
- Other Name: Pulley Assembly-Crankshaft; Harmonic Balancer Puller; Pulley; Pulley, Engine Crankshaft And Camshaft Balancer
Fits the following Pontiac Models:
- Grand Am | 1987-1989 | LE, SE | 4 Cyl 2.0 L GAS
- LeMans | 1989-1990 | GSE, LE, SE | 4 Cyl 2.0 L GAS
- Sunbird | 1987-1994 | Base, GT, LE, LE Value Leader, SE, Value Leader | 4 Cyl 2.0 L GAS
View More
View related parts
Pontiac Crankshaft Pulley Part Number: 10101369
Product Specifications
- Other Name: Pulley; Harmonic Balancer Puller; Pulley, Engine Crankshaft And Camshaft Balancer; Hub, Engine Crankshaft And Camshaft Balancer
Fits the following Pontiac Models:
- 6000 | 1987-1991 | Base, LE | 4 Cyl 2.5 L GAS
- Fiero | 1987-1988 | SE, Sport, Value Leader | 4 Cyl 2.5 L GAS
View related parts
Pontiac Vibration Damper Part Number: 14083394
Product Specifications
- Other Name: Crankshaft Damper; Harmonic Balancer Puller; Torsion Damper; Pulley; Damper, Engine Crankshaft And Camshaft Balancer
Fits the following Pontiac Models:
- 6000 | 1984-1986 | Base, LE, SE, STE | 6 Cyl 2.8 L GAS
View related parts
Pontiac Vibration Damper Part Number: 12551948
Product Specifications
- Other Name: Pulley; Damper; Balancer, Engine Crankshaft And Camshaft Balancer; Damper, Engine Crankshaft And Camshaft Balancer
Fits the following Pontiac Models:
- Bonneville | 1984-1986 | Base, Brougham, LE | 8 Cyl 5.0 L GAS
- Firebird | 1984-1992 | Base, Formula, S/E, Trans Am | 8 Cyl 5.0 L GAS
- Grand Prix | 1985-1987 | Base, Brougham, LE | 8 Cyl 5.0 L GAS
- Parisienne | 1985-1986 | Base, Brougham | 8 Cyl 5.0 L GAS
- Safari | 1987 | Base | 8 Cyl 5.0 L GAS
View More
View related parts
Pontiac Vibration Damper Part Number: 527383
Product Specifications
- Other Name: Balancer Assembly, Crankshaft
Fits the following Pontiac Models:
- Grand Prix | 1986-1987 | Base, Brougham, LE | 6 Cyl 4.3 L GAS
View related parts
Pontiac Crankshaft Pulley Part Number: 88959266
Product Specifications
- Other Name: Damper, Engine Crankshaft And Camshaft Balancer; Harmonic Balancer Puller; Harmonic Balancer; Pulley; Balancer; Pulley, Engine Crankshaft And Camshaft Balancer
- Replaces: 25527381
Fits the following Pontiac Models:
- Bonneville | 1987-1988 | Base, LE, SE, SSE | 6 Cyl 3.8 L GAS
View related parts
Pontiac Pulley Part Number: 22521773
Product Specifications
- Other Name: Pulley, Engine Crankshaft
Fits the following Pontiac Models:
- Bonneville | 1984 | Base, Brougham, LE | 8 Cyl 5.7 L DIESEL
- Parisienne | 1984-1985 | Base, Brougham | 8 Cyl 5.7 L DIESEL
View related parts
Pontiac Crankshaft Pulley Part Number: 90299069
Product Specifications
- Other Name: Pulley, Engine Crankshaft And Camshaft Balancer; Harmonic Balancer Puller; Pulley
Fits the following Pontiac Models:
- LeMans | 1989-1993 | LE, SE, Value Leader | 4 Cyl 1.6 L GAS

| Page 1 of 3 |Next >

1-20 of 42 Results

Pontiac Crankshaft Pulley

Choose OEM Crankshaft Pulley, you're making the optimal decision for superior quality and perfect performance. You can feel confident because each component goes through stringent quality checks. Every part is carefully built to comply with Pontiac's factory specifications. You'll enjoy a smooth, worry-free installation that fits just right. At ChevyPartsDeal.com, you'll find it easy to get top-quality OEM Pontiac Crankshaft Pulley. You can shop at highly competitive prices and protect your budget. All our genuine Pontiac parts include a dependable manufacturer's warranty. You'll also appreciate our straightforward return policy and swift delivery services for extra convenience.

Pontiac Crankshaft Pulley eliminates engine vibration during driving and has steering, air-con and charge feeding belts. By combining defiant appearance with fair play, Pontiac became a brand that bold drivers can take home and that generates excitement at an affordable cost instead of emptying them. The unfiltered steering and the deep-rooted Pontiac stance, which is known as the wide-track stance, resulted in a planted Pontiac that made daily commutes feel like a rewarding experience of control. Pontiac applied fun as the first priority and comfort as a reward; therefore, even base models came with a smile per mile outlook. It was a promise of boisterous throttle action, simple mechanics and looks that never aimed to be the same, features that continue to sound out each time a person pops behind one of these vintage dashboards. The Crankshaft Pulley itself is bolted directly to the crank nose and rotates in perfect synchronization, sending torque through serpentine belts to the alternator, power steering pump, and A/C compressor, and its inherent weight absorbs vibrations before they can cause the block to shake. The initial ones were made of cast iron, and they were replaced by lighter alloys; therefore, every Crankshaft Pulley balances power with lightness of rotation and assists the revs to rise faster. Due to a uniform hub depth and groove separation, a Crankshaft Pulley of one year can frequently be installed on others, providing shade-tree hackers an inexpensive route to a smoother ride.

Pontiac Crankshaft Pulley Parts and Q&A

Crankshaft Pulley
10127523
Q: How to remove and install the crankshaft pulley in 2.2L four cylinder engine on Pontiac Grand Prix?
A:
To undo the component, one must turn off the car and then undo the clamp connector at the negative battery terminal so that the Theftlock audio system cannot lock out the disconnection if installed. After that remove the drivebelt, then lift the front of the vehicle and place it on jackstands in a securely manner, then remove the right front tire and inner fender splash shield. Take out the pulley-to-crankshaft bolt, with a breaker bar, if it is very stiff. If required, remove the lower bell housing cover and using a large screwdriver; place it through the flywheel or driveplate ring gear to stop the crankshaft from coming round when loosening up or doing up the bolt. Subsequently, take out the three bolts fastening the pulley on the hub then use the puller to, For installation, use clean multi purpose grease on the seal contact part of the hub and then place the hub over the crankshaft and slide it on until it gets up against the crankshaft gear with the slot in the hub best fitting the Woodruff key in crankshaft. Fix hub into place using the pulley-to-crankshaft bolt and tighten the bolt to the recommended torque. Last but not the least, the final stages are always marked by the reversal of the entire removal procedure.
Crank Pulley
12697768
Q: How to disconnect the cable from the negative terminal of the battery and remove the crankshaft pulley in 3.5L,3.9L V6 engine on Pontiac G6?
A:
Disconnect the cable from the negative terminal of the battery. With the parking brake applied and the shift lever in Park, loosen the lug nuts from the right front wheel, then raise the front of the vehicle and support it securely on jackstands. Remove the right front wheel and the right splash shield from the wheel well. Remove the drivebelt. Support the right side of the subframe with a floor jack, remove the right-side subframe bolts, and loosen the left-side subframe bolts, then partially lower the right side of the subframe. Remove the bolt from the front of the crankshaft using a pin spanner to prevent the crankshaft from turning while loosening the pulley bolt, which is normally very tight; use a large breaker bar and a six-point socket for removal. Obtain a new bolt but save the old one for the initial installation of the pulley. Use a puller with three hooks that can grasp the inside diameter of the outer ring of the crankshaft pulley, ensuring the hooks do not attach to the outside of the pulley. Remove the crankshaft pulley/balancer from the crankshaft using a puller that bears on the crankshaft pulley hub, and use a spacer to avoid damage to the crankshaft. Apply a small amount of RTV sealant onto the crankshaft keyway and allow it to set up slightly. Position the crankshaft pulley/balancer on the crankshaft and slide it on as far as it will go, ensuring the slot in the hub aligns with the Woodruff key in the end of the crankshaft. Using a crankshaft balancer installation tool, press the crankshaft pulley/balancer onto the crankshaft, noting that the crankshaft bolt can also be used for this purpose with clean engine oil on the bolt threads to prevent galling. For a 2005 model, install the old bolt and washer and tighten it to the specified torque. For a 2006 or later model, purchase a new bolt, install the old bolt and washer, tighten it to the specified torque, then remove it. Install the new bolt and washer, tightening it to the specified torque followed by the angle torque. The remaining installation steps are the reverse of removal, ensuring to tighten the subframe bolts to the specified torque.