How to Overhaul the Rear Brake Calipers of the 1500 Series on GMC Yukon?

First and foremost, separate the brake caliper from the vehicle to overhaul the rear brake caliper of the 1500 series. Put a thin piece of wood in front of the Piston so as not to get damaged and then remove the Piston using compressed air in the brake hose inlet. Fitting port of brake caliper housing. Next, take away the Piston boot, piston, seal, brake caliper bleed screw cap, and brake caliper bleed screw. Check the brake caliper bore and Piston seal groove for over scoring and corrosion; if found, change the brake caliper housing. Also, inspect brake caliper mounting bracket guide surfaces for corrosion and wear and replace them if need be. Clean all residue from the brake pad guiding surfaces of the brake caliper housing and mounting bracket, and clean all parts not covered in the repair kit with the denatured alcohol during the drying process with filtered unlubricated compressed air. Blow out all passages in the brake caliper housing, and brake caliper bleeder valve. In assembly install the brake caliper bleed screw and tighten it to 12 nm(106 inch lbs.),then install bleed screw cap. Wrap the new Piston seal with brake fluid to lubricate the seal and not twisting the seal before placing the seal on the groove of the brake caliper bore. Lubricate the brake caliper bore and the Piston with brake fluid and then insert the boot over the end of the Piston with a fold closure towards the brake caliper housing Piston bore opening. Secure the boot in the brake caliper bore groove, position the Piston in the bore and press down to the bottom of it, while making sure that the boot seats into the Piston groove and brake caliper bore groove properly. Reapply the lubrication and installation for the other Piston and then fit the brake caliper to the vehicle.

How to replace the rear brake calipers on the 1500 Series on GMC Yukon?

To change the rear brake caliper on the 1500 series, inspect first the brake master cylinder reservoir fluid level; if it is higher than the mean point between the maximum-full and minimum allowable levels, drain until it is at that point. Lift and support the vehicle and remove the tire and wheel assembly. Clean the brake hose fitting then use a large c-clamp over the caliper housing pressed against the back of the outboard pad till the piston is fully compressed as well. Cap or plug the brake pipe to prevent loss of fluid, then remove the brake hose to caliper bolt and lay the hose out of the way, and make sure the old copper gaskets are not left to the caliper or hose and dispose of the used ones. Undo the guide pin bolt by using hand tools just when pinching the guide pin by means of an open end wrench and then remove brake caliper from the mounting bracket. For installation, mount new brake caliper to the mounting bracket, clean the threads of the guide pin bolts with brake parts cleaner, then apply threadlocker gm p/n 12345493 (Canadian P/N 10953488) before turning in threads. Again, you would have to use the hand tools to tighten the guide pin bolt to 38 n.m (28 lb.ft.) while you hold the guide pin at a particular point. Remove rubber cap form the brake hose fitting then insert 2 new copper gaskets and then attach brake hose to caliper bolt, also tighten to 40 n.m (30 lb ft). Bleed the hydraulic brake system, install the tire and wheel assembly, and, if needed, fill the master cylinder reservoir to the appropriate level using fresh brake fluid.

OEM GMC Yukon Brake Calipers

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

24 Brake Calipers found

View related parts
GMC Yukon Caliper, Rear Driver Side Part Number: 84191288
$136.61 MSRP: $263.52
You Save: $126.91 (49%)
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Rear Brake (W/O Brake Pads & Bracket; Brake Caliper
- Position: Rear Driver Side
- Replaced by: 86785193
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2020 GMC Yukon | Denali, Denali Hybrid, Hybrid, SLE, SLT | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
GMC Yukon Caliper, Rear Passenger Side Part Number: 84191287
$136.73 MSRP: $266.06
You Save: $129.33 (49%)
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Rear Brake (W/O Brake Pads & Bracket; Brake Caliper
- Position: Rear Passenger Side
- Replaced by: 86785192
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2020 GMC Yukon | Denali, Denali Hybrid, Hybrid, SLE, SLT | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
GMC Yukon Caliper Part Number: 19331021
$170.23 MSRP: $328.77
You Save: $158.54 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Rear
- Replaces: 18040101, 25848000
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2006 GMC Yukon | Denali, SL, SLE, SLT | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
GMC Yukon Caliper Part Number: 85136404
$173.00 MSRP: $324.88
You Save: $151.88 (47%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Rear Brake (W/O Brake Pads & Bracket) *Torch Red; Caliper, Wheel Brake Cylinder/Caliper
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023 GMC Yukon | AT4, Denali, SLE, SLT | 6 Cyl 3.0 L DIESEL, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
View related parts
GMC Yukon Caliper, Red Caliper, Rear Part Number: 85539313
$303.94 MSRP: $550.12
You Save: $246.18 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Rear Brake; Caliper, Wheel Brake Cylinder/Caliper
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2023 GMC Yukon | AT4, Denali, SLE, SLT | 6 Cyl 3.0 L DIESEL, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
View related parts
GMC Yukon Caliper, Red Caliper Part Number: 85136400
$196.33 MSRP: $355.34
You Save: $159.01 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Rear Brake (W/O Brake Pads & Bracket); Caliper, Wheel Brake Cylinder/Caliper
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023 GMC Yukon | AT4, Denali, SLE, SLT | 6 Cyl 3.0 L DIESEL, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
View related parts
GMC Yukon Caliper, Red Caliper, Rear Part Number: 85539312
$322.82 MSRP: $606.24
You Save: $283.42 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Rear Brake; Caliper, Wheel Brake Cylinder/Caliper
- Position: Rear
- Replaced by: 85082366
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2023 GMC Yukon | AT4, Denali, SLE, SLT | 6 Cyl 3.0 L DIESEL, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
View related parts
GMC Yukon Caliper, Red Caliper Part Number: 86824273
$450.64 MSRP: $714.15
You Save: $263.51 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Front Brake (W/O Brake Pads & Bracket*Performance D; Caliper, Wheel Brake Cylinder/Caliper; Caliper, Brakes
- Replaced by: 86555788
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023 GMC Yukon | AT4, Denali, SLE, SLT | 6 Cyl 3.0 L DIESEL, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
View related parts
GMC Yukon Caliper, Red Caliper, Rear Driver Side Part Number: 13537061
$67.75 MSRP: $122.63
You Save: $54.88 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Rear Brake (W/O Brake Pads & Bracket); Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Rear Driver Side
- Replaces: 13522580
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2023 GMC Yukon | AT4, Denali, SLE, SLT | 6 Cyl 3.0 L DIESEL, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
View related parts
GMC Yukon Caliper, Red Caliper, Rear Passenger Side Part Number: 13522581
$56.32 MSRP: $106.97
You Save: $50.65 (48%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Rear Brake (W/O Brake Pads & Bracket; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2023 GMC Yukon | AT4, Denali, SLE, SLT | 6 Cyl 3.0 L DIESEL, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
View related parts
GMC Yukon Caliper, Red Caliper, Driver Side Part Number: 84793057
$496.59 MSRP: $897.28
You Save: $400.69 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Front Brake (W/O Brake Pads & Bracket); Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Driver Side
- Replaced by: 86555791
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2023 GMC Yukon | AT4, Denali, SLE, SLT | 6 Cyl 3.0 L DIESEL, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
View related parts
GMC Yukon Caliper, Red Caliper, Passenger Side Part Number: 84793058
$481.76 MSRP: $903.14
You Save: $421.38 (47%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Front Brake (W/O Brake Pads & Bracket); Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Passenger Side
- Replaced by: 86555792
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2023 GMC Yukon | AT4, Denali, SLE, SLT | 6 Cyl 3.0 L DIESEL, 8 Cyl 5.3 L GAS, 8 Cyl 6.2 L GAS
View related parts
GMC Yukon Caliper, Passenger Side Part Number: 85569602
$96.77 MSRP: $187.82
You Save: $91.05 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Front Brake (W/O Brake Pads & Bracket); Caliper, Wheel Brake Cylinder/Caliper
- Position: Passenger Side
- Replaces: 15904195, 23290150, 84828461, 89059121, 23276880, 22842351
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2020 GMC Yukon | Denali, Denali Hybrid, Hybrid, SLE, SLT | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
GMC Yukon Caliper Part Number: 88967106
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006 GMC Yukon | Denali, SL, SLE, SLT | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
GMC Yukon Caliper Part Number: 88967107
Product Specifications
- Other Name: Caliper Assembly, Rear Brake; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006 GMC Yukon | Denali, SL, SLE, SLT | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
GMC Yukon Caliper, Driver Side Part Number: 18043520
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 GMC Yukon | Denali, SLE, SLT | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
GMC Yukon Caliper, Passenger Side Part Number: 18043521
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 GMC Yukon | Denali, SLE, SLT | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
GMC Yukon Overhaul Kit, Rear Part Number: 18043518
Product Specifications
- Other Name: Caliper Kit, Rear Brake; Brake Caliper Repair Kit; Disc Brake Hardware Kit; Caliper Kit, Wheel Brake Cylinder/Caliper
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2006 GMC Yukon | Denali, SL, SLE, SLT | 8 Cyl 4.8 L GAS, 8 Cyl 5.3 L FLEX, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
GMC Yukon Caliper, Front Part Number: 18014745
Product Specifications
- Other Name: Caliper, Front Brake; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-2000 GMC Yukon | Base, Denali, GT, SL, SLE, SLT, Sport | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL
View related parts
GMC Yukon Caliper, Front Part Number: 18014744
Product Specifications
- Other Name: Caliper, Front Brake; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-2000 GMC Yukon | Base, Denali, GT, SL, SLE, SLT, Sport | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL

| Page 1 of 2 |Next >

1-20 of 24 Results

GMC Yukon Brake Calipers

Want to cut long-term maintenance and repair costs? Choose OEM Brake Calipers. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine GMC Yukon parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM GMC Yukon Brake Calipers includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

It is used in GMC Yukon vehicles and involves conversion of hydraulic pressure supplied by the master cylinder into mechanical force in the Brake Caliperss. This force is crucial in shaving the brake pads against the rotors hence slowing down or even stopping the vehicle. GMC Yukons utilize two primary types of brake calipers: As to the structure, it is divided into two types namely fixed and floating. In fixed calipers there are many pistons at the either side of the rotor to exert even pressure and for better results. To the contrary, floating calipers have pistons on one end and move to push the pads, which can have problems such as uneven wore out pads if not well maintained. Of course, brake calipers have developed over the years as well: there are OEM calipers that are sufficient enough for daily use, performance calipers that increase stopping capacity and look cooler. Calipers used for performance may feature; light weight material with high temperature seals depending on the type of performance of a car or the inclination of an individual. It is very important to inspect and maintain brake caliper very often in order to have the proper performance and safety.

GMC Yukon Brake Calipers Parts and Q&A

Caliper
19331021
Q: How to Overhaul the Rear Brake Calipers of the 1500 Series on GMC Yukon?
A:
First and foremost, separate the brake caliper from the vehicle to overhaul the rear brake caliper of the 1500 series. Put a thin piece of wood in front of the Piston so as not to get damaged and then remove the Piston using compressed air in the brake hose inlet. Fitting port of brake caliper housing. Next, take away the Piston boot, piston, seal, brake caliper bleed screw cap, and brake caliper bleed screw. Check the brake caliper bore and Piston seal groove for over scoring and corrosion; if found, change the brake caliper housing. Also, inspect brake caliper mounting bracket guide surfaces for corrosion and wear and replace them if need be. Clean all residue from the brake pad guiding surfaces of the brake caliper housing and mounting bracket, and clean all parts not covered in the repair kit with the denatured alcohol during the drying process with filtered unlubricated compressed air. Blow out all passages in the brake caliper housing, and brake caliper bleeder valve. In assembly install the brake caliper bleed screw and tighten it to 12 nm(106 inch lbs.),then install bleed screw cap. Wrap the new Piston seal with brake fluid to lubricate the seal and not twisting the seal before placing the seal on the groove of the brake caliper bore. Lubricate the brake caliper bore and the Piston with brake fluid and then insert the boot over the end of the Piston with a fold closure towards the brake caliper housing Piston bore opening. Secure the boot in the brake caliper bore groove, position the Piston in the bore and press down to the bottom of it, while making sure that the boot seats into the Piston groove and brake caliper bore groove properly. Reapply the lubrication and installation for the other Piston and then fit the brake caliper to the vehicle.
Caliper, Rear Passenger Side
84191287
Q: How to replace the rear brake calipers on the 1500 Series on GMC Yukon?
A:
To change the rear brake caliper on the 1500 series, inspect first the brake master cylinder reservoir fluid level; if it is higher than the mean point between the maximum-full and minimum allowable levels, drain until it is at that point. Lift and support the vehicle and remove the tire and wheel assembly. Clean the brake hose fitting then use a large c-clamp over the caliper housing pressed against the back of the outboard pad till the piston is fully compressed as well. Cap or plug the brake pipe to prevent loss of fluid, then remove the brake hose to caliper bolt and lay the hose out of the way, and make sure the old copper gaskets are not left to the caliper or hose and dispose of the used ones. Undo the guide pin bolt by using hand tools just when pinching the guide pin by means of an open end wrench and then remove brake caliper from the mounting bracket. For installation, mount new brake caliper to the mounting bracket, clean the threads of the guide pin bolts with brake parts cleaner, then apply threadlocker gm p/n 12345493 (Canadian P/N 10953488) before turning in threads. Again, you would have to use the hand tools to tighten the guide pin bolt to 38 n.m (28 lb.ft.) while you hold the guide pin at a particular point. Remove rubber cap form the brake hose fitting then insert 2 new copper gaskets and then attach brake hose to caliper bolt, also tighten to 40 n.m (30 lb ft). Bleed the hydraulic brake system, install the tire and wheel assembly, and, if needed, fill the master cylinder reservoir to the appropriate level using fresh brake fluid.