How to replace the front seat belt on Chevrolet Trailblazer?

Starting a front Seat Belt replacement requires first removing the seat switch bezel together with the seat trim panel. The seat adjuster assembly requires its anchor nut to be removed first followed by removing the screw from the front seat back Seat Belt bezel before the bezel slides off the Seat Belt. You should first remove the seat back cover together with pad along with the seat back panel from the seat back frame. Sliding the Seat Belt through its slot will allow you to separate it from the retractor bracket before you unscrew and remove the lower Seat Belt retractor retaining bolt and related nut. The push pin which holds the retractor assembly to the seat back frame must be pulled before removing the bracket bolt of the Seat Belt retractor from both frame components. Install the Seat Belt retractor bracket onto the seat back frame then attach the Seat Belt retractor bracket bolt while torquing it to 55 n.m (40 lb ft). The Seat Belt retractor assembly should be connected to the seat back frame followed by the push pin installation to secure the position. Mount the lower Seat Belt retractor bolt by tightening it to 55 n.m (40 lb ft), afterwards guide the Seat Belt into the retractor bracket through its slot. Finish the installation sequence with the recovery of seat back panel to frame before installing seat back pad and cover. The front seat bezel component of the Seat Belt must slide onto the Seat Belt before securing it to the retractor bracket by screwing it tight to reach 6 n.m (53 lb in). Fasten the Seat Belt anchor onto the seat adjuster assembly while keeping the webbing untwisted and tighten the seat back anchor nut to 52 n.m (38 lb ft). Conclude the task through seat switch bezel and seat trim panel reinvestment.

How to service the front seat belt on Chevrolet Trailblazer?

Service of the front Seat Belt begins by taking off the seat switch bezel and seat trims panel. Start by uninstalling the Seat Belt anchor nut from the seat adjuster assembly before removing the screw from the front seat back Seat Belt bezel so you can slide off the bezel from the Seat Belt. Start by taking out the seat back cover along with pad before removing the seat back panel from the seat back frame. Remove the lower Seat Belt retractor retaining bolt first followed immediately by the nut before detaching the Seat Belt from the retractor bracket using the slot opening method. First remove the push pin from the seat back frame and then take off the Seat Belt retractor bracket bolt from the bracket and seat back frame for extraction of the retractor assembly. The Seat Belt retractor bracket installation requires the bracket to be positioned on the seat back frame then the bolt needs to be tightened to 55 n.m (40 lb ft). After placing the Seat Belt retractor assembly onto the seat back frame you need to insert the push pin for assembly retention. Guide the Seat Belt into the retractor bracket through the slot after tightening the lower Seat Belt retractor bolt to 55 n.m (40 lb ft). Begin by repositioning the seat back panel onto the seat back frame and then install the seat back pad before applying the seat back cover. The Seat Belt bezel should slide onto the belt and attach to the retractor bracket through the screw which must be tightened to 6 n.m (53 lb in). The final step includes linking the Seat Belt anchor to the seat adjuster assembly through the nut while maintaining the Seat Belt webbing untwisted and securing the seat back anchor nut to 52 n.m (38 lb ft). After this, reinstall the seat trim panel and the seat switch bezel.

OEM Chevrolet Trailblazer Seat Belt

Seat Safety Belt

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

74 Seat Belts found

View related parts
Chevrolet Trailblazer Outer Belt Assembly, Jet Black, Passenger Side Part Number: 42814458
$165.05 MSRP: $246.77
You Save: $81.72 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Retractor Kit-Rear Seat Belt *Jet Black; Retractor Kit, Seat Belt
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2024 Chevrolet Trailblazer | ACTIV, LS, LT, RS | 3 Cyl 1.2 L GAS, 3 Cyl 1.3 L GAS
View related parts
Chevrolet Trailblazer Outer Belt Assembly, Jet Black, Driver Side Part Number: 42814454
$165.05 MSRP: $246.77
You Save: $81.72 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Retractor Kit-Rear Seat Belt *Jet Black; Retractor Kit, Seat Belt
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2024 Chevrolet Trailblazer | ACTIV, LS, LT, RS | 3 Cyl 1.2 L GAS, 3 Cyl 1.3 L GAS
View related parts
Chevrolet Trailblazer Lap & Shoulder Belt, Rear Driver Side Part Number: 19177478
$7.55 MSRP: $11.24
You Save: $3.69 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Belt Kit, Rear Seat (Retractor Side) *Ebony *Ebony; Belt & Retractor; Belt Kit, Am9 - Rear Split Back Folding (65/35)
- Position: Rear Driver Side
- Replaces: 89023886
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2009 Chevrolet Trailblazer | Base, LS, LT, SS | 6 Cyl 4.2 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Trailblazer Buckle End, Gray Part Number: 89023873
$5.22 MSRP: $7.77
You Save: $2.55 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Belt Kit, Rear Seat Center (Buckle Side) *Light Gray *Gray; Latch; Belt Kit, Am9 - Rear Split Back Folding (65/35)
- Position: Rear Center
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2009 Chevrolet Trailblazer | Base, LS, LT, SS | 6 Cyl 4.2 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Trailblazer Lap & Shoulder Belt, Jet Black, Driver Side Part Number: 42750220
$93.35 MSRP: $138.94
You Save: $45.59 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Retractor Kit-Rear Seat Belt *Jet Black; Outer Belt Assembly
- Position: Driver Side
- Replaced by: 42800647
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2023 Chevrolet Trailblazer | ACTIV, L, LS, LT, RS | 3 Cyl 1.2 L GAS, 3 Cyl 1.3 L GAS
View related parts
Chevrolet Trailblazer Lap & Shoulder Belt, Driver Side Part Number: 15232163
$59.73 MSRP: $88.90
You Save: $29.17 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Belt Assembly-Driver Seat (Retractor Side) *Ebony; Belt & Retractor
- Position: Driver Side
- Replaced by: 15290143
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2007 Chevrolet Trailblazer | LS, LT, SS | 6 Cyl 4.2 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Trailblazer Lap & Shoulder Belt, Rear Passenger Side Part Number: 10357697
$63.84 MSRP: $95.00
You Save: $31.16 (33%)
Product Specifications
- Other Name: Belt, Am9 - Rear Split Back Folding (65/35); Belt & Retractor
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2003 Chevrolet Trailblazer | LS, LT, LTZ, North Face | 6 Cyl 4.2 L GAS
View related parts
Chevrolet Trailblazer Buckle End Part Number: 88955807
Product Specifications
- Other Name: Belt Kit, Passenger Seat (Buckle Side); Latch; Belt Kit, A50 - Front Bucket Seat; Belt Kit, Deluxe
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2004 Chevrolet Trailblazer | LS, LT, LTZ, North Face | 6 Cyl 4.2 L GAS
View related parts
Chevrolet Trailblazer Buckle End, Driver Side Part Number: 19148785
Product Specifications
- Other Name: Belt Kit, Driver Seat (Buckle Side); Latch; Belt Kit, A50 - Front Bucket Seat; Belt Kit, Deluxe
- Position: Driver Side
- Replaces: 89024783
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2009 Chevrolet Trailblazer | Base, LS, LT, SS | 6 Cyl 4.2 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Trailblazer Buckle End Part Number: 88957503
Product Specifications
- Other Name: Belt Kit, Am7 - Rear Folding Bucket/Split Bench; Latch
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2004 Chevrolet Trailblazer | LS, LT, LTZ, North Face | 6 Cyl 4.2 L GAS
View related parts
Chevrolet Trailblazer Lap & Shoulder Belt Part Number: 88956143
Product Specifications
- Other Name: Belt Kit, A50 - Front Bucket Seat; Belt & Retractor; Belt Kit, Deluxe
- Position: Passenger Side
- Replaces: 88955809, 88950983
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2003 Chevrolet Trailblazer | LS, LT, LTZ, North Face | 6 Cyl 4.2 L GAS
View related parts
Chevrolet Trailblazer Buckle End, Gray Part Number: 19148786
Product Specifications
- Other Name: Belt Kit, Seat Belt; Latch; Belt Kit, A50 - Front Bucket Seat; Belt Kit, Deluxe
- Position: Driver Side
- Replaces: 89024784
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2009 Chevrolet Trailblazer | Base, LS, LT, SS | 6 Cyl 4.2 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Trailblazer Lap & Shoulder Belt, Gray, Front Driver Side Part Number: 19148782
Product Specifications
- Other Name: Belt Kit, A50 - Front Bucket Seat; Belt & Retractor; Belt Kit, Deluxe
- Position: Front Driver Side
- Replaces: 89024781
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2009 Chevrolet Trailblazer | Base, LS, LT, SS | 6 Cyl 4.2 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Trailblazer Buckle End Part Number: 89023883
$9.12 MSRP: $13.57
You Save: $4.45 (33%)
Product Specifications
- Other Name: Belt Kit, A68 - Rear Folding Seat; Latch; Belt Kit, Am9 - Rear Split Back Folding (65/35)
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2009 Chevrolet Trailblazer | Base, LS, LT, SS | 6 Cyl 4.2 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Trailblazer Lap & Shoulder Belt, Oak Part Number: 88955933
Product Specifications
- Other Name: Belt Kit, Rear Seat #2 (Retractor Side) *Medium Oak *Oak; Belt & Retractor; Belt Kit, Am7 - Rear Folding Bucket/Split Bench
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2003 Chevrolet Trailblazer | LS, LT, LTZ, North Face | 6 Cyl 4.2 L GAS
View related parts
Chevrolet Trailblazer Buckle End Part Number: 88957504
Product Specifications
- Other Name: Belt Kit; Latch; Belt Kit, Am7 - Rear Folding Bucket/Split Bench
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004 Chevrolet Trailblazer | LS, LT, North Face | 6 Cyl 4.2 L GAS
View related parts
Chevrolet Trailblazer Lap & Shoulder Belt, Gray Part Number: 89023867
Product Specifications
- Other Name: Belt Kit, At5 - Rear Center Folding Seat; Center Seat Belt; Belt Kit, Am9 - Rear Split Back Folding (65/35)
- Position: Rear Center
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2009 Chevrolet Trailblazer | Base, LS, LT, SS | 6 Cyl 4.2 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Trailblazer Lap & Shoulder Belt, Gray Part Number: 89022751
Product Specifications
- Other Name: Belt Kit, Am9 - Rear Split Back Folding (65/35); Belt & Retractor
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2006 Chevrolet Trailblazer | LS, LT, SS | 6 Cyl 4.2 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Trailblazer Lap & Shoulder Belt, Gray Part Number: 89022753
Product Specifications
- Other Name: Belt Kit, Am9 - Rear Split Back Folding (65/35); Belt & Retractor
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2006 Chevrolet Trailblazer | LS, LT, SS | 6 Cyl 4.2 L GAS, 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Trailblazer Lap & Shoulder Belt, Oak, Passenger Side Part Number: 15080051
Product Specifications
- Other Name: Belt & Retractor
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2003 Chevrolet Trailblazer | LS, LT, LTZ, North Face | 6 Cyl 4.2 L GAS

| Page 1 of 4 |Next >

1-20 of 74 Results

Chevrolet Trailblazer Seat Belt

Want to cut long-term maintenance and repair costs? Choose OEM Seat Belt. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Trailblazer parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Trailblazer Seat Belt includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

Chevrolet Trailblazer Seat Belt Parts and Q&A

Lap & Shoulder Belt, Gray, Front Passenger Side
19177471
Q: How to replace the front seat belt on Chevrolet Trailblazer?
A:
Starting a front Seat Belt replacement requires first removing the seat switch bezel together with the seat trim panel. The seat adjuster assembly requires its anchor nut to be removed first followed by removing the screw from the front seat back Seat Belt bezel before the bezel slides off the Seat Belt. You should first remove the seat back cover together with pad along with the seat back panel from the seat back frame. Sliding the Seat Belt through its slot will allow you to separate it from the retractor bracket before you unscrew and remove the lower Seat Belt retractor retaining bolt and related nut. The push pin which holds the retractor assembly to the seat back frame must be pulled before removing the bracket bolt of the Seat Belt retractor from both frame components. Install the Seat Belt retractor bracket onto the seat back frame then attach the Seat Belt retractor bracket bolt while torquing it to 55 n.m (40 lb ft). The Seat Belt retractor assembly should be connected to the seat back frame followed by the push pin installation to secure the position. Mount the lower Seat Belt retractor bolt by tightening it to 55 n.m (40 lb ft), afterwards guide the Seat Belt into the retractor bracket through its slot. Finish the installation sequence with the recovery of seat back panel to frame before installing seat back pad and cover. The front seat bezel component of the Seat Belt must slide onto the Seat Belt before securing it to the retractor bracket by screwing it tight to reach 6 n.m (53 lb in). Fasten the Seat Belt anchor onto the seat adjuster assembly while keeping the webbing untwisted and tighten the seat back anchor nut to 52 n.m (38 lb ft). Conclude the task through seat switch bezel and seat trim panel reinvestment.
Buckle End
88955805
Q: How to service the front seat belt on Chevrolet Trailblazer?
A:
Service of the front Seat Belt begins by taking off the seat switch bezel and seat trims panel. Start by uninstalling the Seat Belt anchor nut from the seat adjuster assembly before removing the screw from the front seat back Seat Belt bezel so you can slide off the bezel from the Seat Belt. Start by taking out the seat back cover along with pad before removing the seat back panel from the seat back frame. Remove the lower Seat Belt retractor retaining bolt first followed immediately by the nut before detaching the Seat Belt from the retractor bracket using the slot opening method. First remove the push pin from the seat back frame and then take off the Seat Belt retractor bracket bolt from the bracket and seat back frame for extraction of the retractor assembly. The Seat Belt retractor bracket installation requires the bracket to be positioned on the seat back frame then the bolt needs to be tightened to 55 n.m (40 lb ft). After placing the Seat Belt retractor assembly onto the seat back frame you need to insert the push pin for assembly retention. Guide the Seat Belt into the retractor bracket through the slot after tightening the lower Seat Belt retractor bolt to 55 n.m (40 lb ft). Begin by repositioning the seat back panel onto the seat back frame and then install the seat back pad before applying the seat back cover. The Seat Belt bezel should slide onto the belt and attach to the retractor bracket through the screw which must be tightened to 6 n.m (53 lb in). The final step includes linking the Seat Belt anchor to the seat adjuster assembly through the nut while maintaining the Seat Belt webbing untwisted and securing the seat back anchor nut to 52 n.m (38 lb ft). After this, reinstall the seat trim panel and the seat switch bezel.