How to replace the rear door hinge on the door side on Chevrolet Silverado 3500?

Start by removing door panels while also removing components attached to the hinge. After removing an excess amount of sealer you should write the location of the hinge on the pillar. Sand the existing hinge lightly with 100 grit or finer sandpaper starting from its attachment points to the pillar while puncturing the welds in their centers for simple drilling later. Punch the centers of each weld mark on the original hinge but avoid drilling into the door. Use a 13 mm (1/2 in) rotabroach hole saw as well as other comparable tools to drill through the hinge at the punch locations while also employing a chisel if needed to detach the hinge from the door surface. A smooth surface must form on the door because all welding remnants need removal before the service hinge can utilize it. The door must be fixed from all drilling and hinge removal damage before cleaning the backing plate surfaces and preparing them for smooth mounting. The door service hinge needs to be placed inside the scribe marks and then each hole location needs to be center punched before drilling 3 mm (1/8 in) pilot holes at every mark using a drill bit of exact size. Clean up all exposed metal surfaces before applying approved anti-corrosion primer to them. After drilling 11.5 mm (29/64 inches) holes at the stud positions and creating pilot holes, treat all surfaces with anti-corrosion products. Apply full-bodied caulk across the entire hinge mounting surface before aligning the hinge together with the backing plate with the door holes. Afterward install the bolts and tighten the pillar nuts to 25 N.m (18 lb ft). The technician will finish the workspace by applying sealers followed by refinishing procedures before accomplishing component and panel installation.

How to replace the front door hinge on Chevrolet Silverado 3500?

Commence front door hinge replacement by first clearing all associated parts followed by removing excess sealer from the present hinge location and writing down the position on the hinge pillar. Scrape away the 100 grit or finer surface of the existing hinge to identify its four door weld locations while marking the weld centers for drilling later. Use a center punch to mark the centers of the four weld marks on the original hinge base while avoiding drill penetration of the door. Drive a 13 mm (1/2 in) rotabroach hole saw through the hinge base to match the punch points. Thoroughly remove the hinge by using a chisel as needed while clearing away all remaining weld material so the service hinge can fit without gaps to the door surface. After fixing any door harm caused by drilling or hinge removal you should clean and prepare both backing plate mounting surfaces with a flat profile fit. Set the service hinge inside the door scribe marks then use center punches to mark each hole position according to the hinge. Drill three center punch holes with a 3mm (1/8 inch) pilot drill starting from the exact drill bit size before moving to the 11.5mm (29/64 inch) hole at these pilot markings. All exposed metal parts need preparation followed by approved anti-corrosion primer coating before applying full-bodied caulk to create a secure boundary across entire hinge mounting surfaces. Use the hinge along with the backing plate to match up with the door holes before tightening bolts to 25 N.m (18 lb ft) tension. The last procedure includes applying the sealers before finishing the metal surfaces according to specifications while reattaching and aligning all functional components.

OEM Chevrolet Silverado 3500 Door Hinge

Interior Door Hinge

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

18 Door Hinges found

View related parts
Chevrolet Silverado 3500 Hinge, Passenger Side Part Number: 15078746
$54.31 MSRP: $80.83
You Save: $26.52 (33%)
ADD TO CART
Product Specifications
- Other Name: Hinge, End Gate Closing; Door Hinge
- Position: Passenger Side
- Replaces: 15756846
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2006 Chevrolet Silverado 3500 | Base, LS, LT, WT | 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL, 8 Cyl 8.1 L GAS
View related parts
Chevrolet Silverado 3500 Hinge, Driver Side Part Number: 15078745
$51.69 MSRP: $76.93
You Save: $25.24 (33%)
ADD TO CART
Product Specifications
- Other Name: Hinge, End Gate Closing; Door Hinge
- Position: Driver Side
- Replaces: 15711263, 15756845, 15051751, 15051753, 15032975
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2006 Chevrolet Silverado 3500 | Base, LS, LT, WT | 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL, 8 Cyl 8.1 L GAS
View related parts
Chevrolet Silverado 3500 Hinge, Driver Side Part Number: 15074253
$45.24 MSRP: $67.33
You Save: $22.09 (33%)
ADD TO CART
Product Specifications
- Other Name: Door Hinge; Hinge, End Gate Closing
- Position: Driver Side
- Replaces: 15756842
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2006 Chevrolet Silverado 3500 | Base, LS, LT, WT | 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL, 8 Cyl 8.1 L GAS
View related parts
Chevrolet Silverado 3500 Hinge, Passenger Side Part Number: 15074252
$45.24 MSRP: $67.33
You Save: $22.09 (33%)
ADD TO CART
Product Specifications
- Other Name: Door Hinge; Hinge, End Gate Closing
- Position: Passenger Side
- Replaces: 15051750, 15051752, 15032976, 15711264, 15756848
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2006 Chevrolet Silverado 3500 | Base, LS, LT, WT | 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL, 8 Cyl 8.1 L GAS
View related parts
Chevrolet Silverado 3500 Lower Hinge, Driver Side Part Number: 12472843
$64.29 MSRP: $92.79
You Save: $28.50 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hinge Kit, Door Hinge; Upper Hinge; Hinge; Door Hinge
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2006 Chevrolet Silverado 3500 | Base, LS, LT, WT | 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL, 8 Cyl 8.1 L GAS
View related parts
Chevrolet Silverado 3500 Lower Hinge, Front Part Number: 19354132
$157.07 MSRP: $245.85
You Save: $88.78 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hinge Kit, Front Side Door (Body Side); Door Hinge; Upper Hinge; Hinge; Hinge Kit, Door Hinge
- Position: Front
- Replaces: 12476447, 12477887, 12472841
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2006 Chevrolet Silverado 3500 | Base, LS, LT, WT | 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL, 8 Cyl 8.1 L GAS
View related parts
Chevrolet Silverado 3500 Hinge, Passenger Side Part Number: 12472846
$264.57 MSRP: $395.55
You Save: $130.98 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hinge Kit, Door Hinge; Door Hinge
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2006 Chevrolet Silverado 3500 | Base, LS, LT, WT | 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL, 8 Cyl 8.1 L GAS
View related parts
Chevrolet Silverado 3500 Hinge, Rear Driver Side Part Number: 19354129
$81.14 MSRP: $120.77
You Save: $39.63 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hinge Kit, Rear Side Door (Body Side); Door Hinge; Hinge Kit, Door Hinge
- Position: Rear Driver Side
- Replaces: 12476249
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2006 Chevrolet Silverado 3500 | Base, LS, LT, WT | 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL, 8 Cyl 8.1 L GAS
View related parts
Chevrolet Silverado 3500 Hinge, Rear Passenger Side Part Number: 19353936
$42.27 MSRP: $62.91
You Save: $20.64 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hinge Kit, Rear Side Door (Body Side); Hinge Kit, Door Hinge
- Position: Rear Passenger Side
- Replaces: 12472840
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2006 Chevrolet Silverado 3500 | Base, LS, LT, WT | 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL, 8 Cyl 8.1 L GAS
View related parts
Chevrolet Silverado 3500 Lower Hinge, Front Part Number: 19354133
$161.30 MSRP: $252.48
You Save: $91.18 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hinge Kit, Front Side Door (Body Side); Door Hinge; Upper Hinge; Hinge; Hinge Kit, Door Hinge
- Position: Front
- Replaces: 12476448, 12477888, 12472842
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2006 Chevrolet Silverado 3500 | Base, LS, LT, WT | 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL, 8 Cyl 8.1 L GAS
View related parts
Chevrolet Silverado 3500 Hinge Assembly, Rear Driver Side Part Number: 19354130
$152.76 MSRP: $239.11
You Save: $86.35 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hinge Kit, Rear Side Door (Body Side); Door Hinge; Hinge; Hinge Kit, Door Hinge
- Position: Rear Driver Side
- Replaces: 12476449
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2006 Chevrolet Silverado 3500 | Base, LS, LT, WT | 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL, 8 Cyl 8.1 L GAS
View related parts
Chevrolet Silverado 3500 Hinge Assembly, Passenger Side Part Number: 12476452
$222.71 MSRP: $332.97
You Save: $110.26 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hinge Kit, Door Hinge; Hinge; Door Hinge
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2006 Chevrolet Silverado 3500 | Base, LS, LT, WT | 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL, 8 Cyl 8.1 L GAS
View related parts
Chevrolet Silverado 3500 Hinge, Driver Side Part Number: 12476259
$186.60 MSRP: $269.32
You Save: $82.72 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hinge Kit, Door Hinge; Door Hinge
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2006 Chevrolet Silverado 3500 | Base, LS, LT, WT | 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL, 8 Cyl 8.1 L GAS
View related parts
Chevrolet Silverado 3500 Upper Hinge, Passenger Side Part Number: 12472844
$93.05 MSRP: $179.03
You Save: $85.98 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hinge Kit, Door Hinge; Lower Hinge; Hinge; Door Hinge
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2006 Chevrolet Silverado 3500 | Base, LS, LT, WT | 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL, 8 Cyl 8.1 L GAS
View related parts
Chevrolet Silverado 3500 Hinge, Driver Side Part Number: 15757891
Product Specifications
- Other Name: Door Hinge; Hinge, End Gate Closing
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2004 Chevrolet Silverado 3500 | Base, LS, LT, WT | 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL, 8 Cyl 8.1 L GAS
View related parts
Chevrolet Silverado 3500 Hinge, Passenger Side Part Number: 15757890
Product Specifications
- Other Name: Door Hinge; Hinge, End Gate Closing
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2004 Chevrolet Silverado 3500 | Base, LS, LT, WT | 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL, 8 Cyl 8.1 L GAS
View related parts
Chevrolet Silverado 3500 Hinge Assembly, Rear Passenger Side Part Number: 19354131
$183.76 MSRP: $274.74
You Save: $90.98 (34%)
Product Specifications
- Other Name: Hinge Kit, Rear Side Door (Body Side); Door Hinge; Hinge; Hinge Kit, Door Hinge
- Position: Rear Passenger Side
- Replaces: 12476450
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2006 Chevrolet Silverado 3500 | Base, LS, LT, WT | 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL, 8 Cyl 8.1 L GAS
View related parts
Chevrolet Silverado 3500 Hinge Assembly, Driver Side Part Number: 12476451
$160.60 MSRP: $240.11
You Save: $79.51 (34%)
Product Specifications
- Other Name: Hinge Kit, Door Hinge; Hinge; Door Hinge
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2001-2006 Chevrolet Silverado 3500 | Base, LS, LT, WT | 8 Cyl 6.0 L CNG, 8 Cyl 6.0 L GAS, 8 Cyl 6.6 L DIESEL, 8 Cyl 8.1 L GAS

Chevrolet Silverado 3500 Door Hinge

Want to cut long-term maintenance and repair costs? Choose OEM Door Hinge. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Silverado 3500 parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Silverado 3500 Door Hinge includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

Chevrolet Silverado 3500 Door Hinge Parts and Q&A

Hinge, Passenger Side
12472846
Q: How to replace the rear door hinge on the door side on Chevrolet Silverado 3500?
A:
Start by removing door panels while also removing components attached to the hinge. After removing an excess amount of sealer you should write the location of the hinge on the pillar. Sand the existing hinge lightly with 100 grit or finer sandpaper starting from its attachment points to the pillar while puncturing the welds in their centers for simple drilling later. Punch the centers of each weld mark on the original hinge but avoid drilling into the door. Use a 13 mm (1/2 in) rotabroach hole saw as well as other comparable tools to drill through the hinge at the punch locations while also employing a chisel if needed to detach the hinge from the door surface. A smooth surface must form on the door because all welding remnants need removal before the service hinge can utilize it. The door must be fixed from all drilling and hinge removal damage before cleaning the backing plate surfaces and preparing them for smooth mounting. The door service hinge needs to be placed inside the scribe marks and then each hole location needs to be center punched before drilling 3 mm (1/8 in) pilot holes at every mark using a drill bit of exact size. Clean up all exposed metal surfaces before applying approved anti-corrosion primer to them. After drilling 11.5 mm (29/64 inches) holes at the stud positions and creating pilot holes, treat all surfaces with anti-corrosion products. Apply full-bodied caulk across the entire hinge mounting surface before aligning the hinge together with the backing plate with the door holes. Afterward install the bolts and tighten the pillar nuts to 25 N.m (18 lb ft). The technician will finish the workspace by applying sealers followed by refinishing procedures before accomplishing component and panel installation.
Lower Hinge, Front
19354132
Q: How to replace the front door hinge on Chevrolet Silverado 3500?
A:
Commence front door hinge replacement by first clearing all associated parts followed by removing excess sealer from the present hinge location and writing down the position on the hinge pillar. Scrape away the 100 grit or finer surface of the existing hinge to identify its four door weld locations while marking the weld centers for drilling later. Use a center punch to mark the centers of the four weld marks on the original hinge base while avoiding drill penetration of the door. Drive a 13 mm (1/2 in) rotabroach hole saw through the hinge base to match the punch points. Thoroughly remove the hinge by using a chisel as needed while clearing away all remaining weld material so the service hinge can fit without gaps to the door surface. After fixing any door harm caused by drilling or hinge removal you should clean and prepare both backing plate mounting surfaces with a flat profile fit. Set the service hinge inside the door scribe marks then use center punches to mark each hole position according to the hinge. Drill three center punch holes with a 3mm (1/8 inch) pilot drill starting from the exact drill bit size before moving to the 11.5mm (29/64 inch) hole at these pilot markings. All exposed metal parts need preparation followed by approved anti-corrosion primer coating before applying full-bodied caulk to create a secure boundary across entire hinge mounting surfaces. Use the hinge along with the backing plate to match up with the door holes before tightening bolts to 25 N.m (18 lb ft) tension. The last procedure includes applying the sealers before finishing the metal surfaces according to specifications while reattaching and aligning all functional components.