How to replace the Rear Crossmember in the rear suspension on Chevrolet Corvette?

Begin the rear suspension crossmember replacement by lifting up and supporting the vehicle and removing both tire and wheel assemblies. First disconnect all wheel speed sensors from their harnesses along with coils from park brake cables and remove electrical connectors from esc Shock Absorber harnesses when present. Beginning the process you should remove the rear suspension position sensors and inner tie rod end studs from the Rear Crossmember and lower control arms from the crossmember. Lower control arms, rear suspension knuckles, and tie rods will require support before separating the transverse spring from its position. Install the j 42055 transmission support fixture (J 42055) on a transmission jack then position the fixture securely to support the transmission. Support the crossmember first by disconnecting electric harnesses and brake tubing followed by removing the lower mount nuts. Position a transmission jack underneath to hold the crossmember. Handle all tasks with hand tools only to unscrew the mounting nuts at the Rear Crossmember before extracting the component from the vehicle and discarding the mounting nuts. During installation align the crossmember dowel pins to the frame rails and transaxle mount studs to the crossmember before using new crossmember mounting nuts. Use only hand tools to install and torque new rear suspension crossmember mounting nuts to 110 n.m (81 lb ft). Remove the j 42055 transmission jack from both the transmission and crossmember before connecting all electrical harness retainers and brake pipe retainers to their respective locations on the crossmember. Position the transaxle mount lower nuts before installing the transverse spring and lower control arms and inner tie rod end studs with the rear suspension position sensors. Whenever possible connect electrical connectors to esc Shock Absorber harnesses if present and park brake cables to actuator levers in addition to wheel speed sensor harness connectors. After installation of tires and wheels complete vehicle lowering then perform measurements to adjust rear trim height before conducting a wheel alignment procedure.

How to replace the rear crossmember for the steering gear on Chevrolet SSR?

You should first raise and support the vehicle to begin the replacement of the rear steering gear crossmember. Unbolt the rear mounting points of the rear steering gear crossmember as well as the rear mounting bolts on the front steering gear crossmember and carefully take the crossmember out from the vehicle. Align the rear steering gear crossmember with its mounting holes, put in the bolts, and tighten them to 50 N.m (37 lb ft). Following this, put in and tighten the rear mounting bolts for the front steering gear crossmember to 50 N.m (37 lb ft), then lower the vehicle.

OEM Chevrolet Rear Crossmember

Rear Suspension Crossmember

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

55 Rear Crossmembers found

View related parts
Chevrolet Suspension Crossmember, Rear Part Number: 84176773
$417.85 MSRP: $654.05
You Save: $236.20 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cradle Assembly-Rear; Crossmember
- Position: Rear
- Replaced by: 26443910
Fits the following Chevrolet Models:
- Equinox | 2018-2024 | L, LS, LT, Premier, RS | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L DIESEL, 4 Cyl 2.0 L GAS
View related parts
Chevrolet Suspension Crossmember Part Number: 92261279
$807.81 MSRP: $1565.56
You Save: $757.75 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Support, Rear Suspension; Crossmember
Fits the following Chevrolet Models:
- Caprice | 2011-2012 | PPV | 6 Cyl 3.6 L FLEX, 8 Cyl 6.0 L FLEX
View related parts
Chevrolet Cradle Assembly-Rear Part Number: 26443910
$417.85 MSRP: $654.05
You Save: $236.20 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: CRADLE ASM-RR
- Position: Rear
- Replaces: 84176773, 26389888
Fits the following Chevrolet Models:
- Equinox | 2018-2025 | ACTIV, L, LS, LT, Premier, RS | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L DIESEL, 4 Cyl 2.0 L GAS
View related parts
Chevrolet Crossmember, Rear Part Number: 26389888
$417.85 MSRP: $654.05
You Save: $236.20 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cradle Assembly-Rear; Cradle, Rear Wheel
- Position: Rear
- Replaced by: 26443910
Fits the following Chevrolet Models:
- Equinox | 2023-2024 | LS, LT, Premier, RS | 4 Cyl 1.5 L GAS
View related parts
Chevrolet Suspension Crossmember, Rear Part Number: 84176775
$439.94 MSRP: $688.62
You Save: $248.68 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cradle Assembly-Rear Suspension; Crossmember
- Position: Rear
- Replaced by: 26443909
Fits the following Chevrolet Models:
- Equinox | 2018-2023 | L, LS, LT, Premier, RS | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L DIESEL, 4 Cyl 2.0 L GAS
View related parts
Chevrolet Crossmember, Rear Part Number: 42558092
$217.67 MSRP: $325.43
You Save: $107.76 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Crossmember, Rear Frame Cross
- Position: Rear
- Replaces: 95096640
Fits the following Chevrolet Models:
- Trax | 2015-2022 | LS, LT, LTZ, Premier | 4 Cyl 1.4 L GAS
View related parts
Chevrolet Center Crossmember, Rear Part Number: 19317736
$328.08 MSRP: $490.50
You Save: $162.42 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Crossmember, Rear; Crossmember, Rear Frame Cross
- Position: Rear Center
Fits the following Chevrolet Models:
- City Express | 2015-2018 | LS, LT | 4 Cyl 2.0 L GAS
View related parts
Chevrolet Cradle Assembly-Rear Suspension Part Number: 26443909
$458.53 MSRP: $688.62
You Save: $230.09 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: CRADLE ASM-RR SUSP
- Position: Rear
- Replaces: 26389887, 84176775
Fits the following Chevrolet Models:
- Equinox | 2018-2025 | ACTIV, L, LS, LT, Premier, RS | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L DIESEL, 4 Cyl 2.0 L GAS
View related parts
Chevrolet Suspension Crossmember, Rear Part Number: 26389887
$458.53 MSRP: $688.62
You Save: $230.09 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cradle Assembly-Rear Suspension; Cradle, Rear Wheel
- Position: Rear
- Replaced by: 26443909
Fits the following Chevrolet Models:
- Equinox | 2018-2024 | LS, LT, Premier, RS | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L DIESEL, 4 Cyl 2.0 L GAS
View related parts
Chevrolet Cradle, Rear Wheel Part Number: 84734649
$544.33 MSRP: $817.48
You Save: $273.15 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cradle Assembly-Rear Suspension
- Position: Rear
Fits the following Chevrolet Models:
- Equinox EV | 2024-2025 | LT, RS, RS Launch Edition | BATTERY EV (EV/BEV)
View related parts
Chevrolet Cradle, Rear Wheel Part Number: 87868517
$583.37 MSRP: $876.11
You Save: $292.74 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cradle Assembly-Rear Suspension
- Position: Rear
Fits the following Chevrolet Models:
- Equinox EV | 2024-2025 | LT, RS, RS Launch Edition | BATTERY EV (EV/BEV)
View related parts
Chevrolet Cradle, Rear Wheel Part Number: 85653084
$600.48 MSRP: $901.80
You Save: $301.32 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cradle Assembly-Rear Suspension
- Position: Rear
Fits the following Chevrolet Models:
- Silverado EV | 2024-2025 | LT, RST, WT | BATTERY EV (EV/BEV)
View related parts
Chevrolet Crossmember, Rear Part Number: 19317740
$619.84 MSRP: $930.87
You Save: $311.03 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Crossmember, Rear Frame Cross
- Position: Rear
Fits the following Chevrolet Models:
- City Express | 2015-2018 | LS, LT | 4 Cyl 2.0 L GAS
View related parts
Chevrolet Cradle, Rear Wheel Part Number: 86520370
$760.75 MSRP: $1142.50
You Save: $381.75 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cradle Assembly-Rear Suspension
- Position: Rear
Fits the following Chevrolet Models:
- Blazer EV | 2024-2025 | LT, PPV, RS, SS | BATTERY EV (EV/BEV)
View related parts
Chevrolet Cradle, Rear Wheel Part Number: 85133125
$835.61 MSRP: $1254.92
You Save: $419.31 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cradle Assembly-Rear Suspension
- Position: Rear
- Replaces: 84234619, 84350796
Fits the following Chevrolet Models:
- Traverse | 2018-2025 | High Country, L, LS, LT, Premier, RS, Z71 | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.6 L GAS
- Traverse Limited | 2024 | High Country, LS, LT, Premier, RS | 6 Cyl 3.6 L GAS
View related parts
Chevrolet Cradle, Rear Wheel Part Number: 85133124
$977.69 MSRP: $1468.00
You Save: $490.31 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cradle Assembly-Rear Suspension
- Position: Rear
- Replaces: 84234618, 84350795
Fits the following Chevrolet Models:
- Traverse | 2018-2025 | High Country, L, LS, LT, Premier, RS, Z71 | 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.6 L GAS
- Traverse Limited | 2024 | High Country, LS, LT, Premier, RS | 6 Cyl 3.6 L GAS
View related parts
Chevrolet Cradle Assembly-Rear Suspension Part Number: 85017385
$1025.76 MSRP: $1540.49
You Save: $514.73 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: CRADLE ASM-RR SUSP
- Position: Rear
Fits the following Chevrolet Models:
- Silverado EV | 2024-2025 | LT, RST, WT | BATTERY EV (EV/BEV)
View related parts
Chevrolet Suspension Crossmember, Rear Part Number: 86821780
$1107.62 MSRP: $1663.43
You Save: $555.81 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cradle Assembly-Rear Suspension; Crossmember; Cradle, Rear Wheel
- Position: Rear
- Replaced by: 86544558
Fits the following Chevrolet Models:
- Blazer EV | 2024-2025 | LT, PPV, RS, SS | BATTERY EV (EV/BEV)
View related parts
Chevrolet Crossmember, Rear Part Number: 42732352
$41.24 MSRP: $61.38
You Save: $20.14 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Crossmember, Rear Frame Cross
- Position: Rear
Fits the following Chevrolet Models:
- Trailblazer | 2021-2025 | ACTIV, L, LS, LT, RS | 3 Cyl 1.2 L FLEX, 3 Cyl 1.2 L GAS, 3 Cyl 1.3 L GAS
View related parts
Chevrolet Crossmember Part Number: 15981865
Product Specifications
- Other Name: Member, Frame Support Cross; Crossmember, Rear Frame Cross
Fits the following Chevrolet Models:
- Tahoe | 1997-2000 | Base, LS, LT, Limited, Z71 | 8 Cyl 5.7 L GAS, 8 Cyl 6.5 L DIESEL

| Page 1 of 3 |Next >

1-20 of 55 Results

Chevrolet Rear Crossmember

Choose OEM Rear Crossmember, you're making the optimal decision for superior quality and perfect performance. You can feel confident because each component goes through stringent quality checks. Every part is carefully built to comply with Chevrolet's factory specifications. You'll enjoy a smooth, worry-free installation that fits just right. At ChevyPartsDeal.com, you'll find it easy to get top-quality OEM Chevrolet Rear Crossmember. You can shop at highly competitive prices and protect your budget. All our genuine Chevrolet parts include a dependable manufacturer's warranty. You'll also appreciate our straightforward return policy and swift delivery services for extra convenience.

Chevrolet Rear Crossmember distribute weight of the drivetrain to increase stability on regular drives and severe pulls. Since 1911, Chevy has earned trust through order deliveries of cars that combine fun to power and comfortable living. The simple controls, realistic prices, and a design language that is not shouting at you make drivers appreciate them. Chevy continues to tweak engines and add driver aids such as hands-free cruising on tiny two-door cruisers up to big pickups. Cabin loyalists of road trips prefer the spacious cabins and commuters the fuel efficiency offered by newer powertrains. Chevrolet introduces these features throughout the range because customers can skip a nimble hatch to a heavy hauler without having to learn the fundamentals again. Chevy also takes the feedback of fans and implements changes, which are quickly implemented rather than taking a complete model cycle. Extended warranty and value are also very owner-friendly. The Rear Crossmember is positioned low and between the frame rails and it connects engine mounts near the crossmember area of the truck. It fixes the chassis making the steering inputs almost direct and the changes in the payload not to bend the structure. Torque bursts of the crankshaft are diverted by the component paths which load through solid steel plates and into the frame, eliminating vibration and metal fatigue. Corrosion resistant surfaces combat road salts and drainage holes allow mud and water to pass through so that corrosion can be kept off. The frequent bumps on urban roads or gravel paths do not mean much to the Rear Crossmember since the geometry has the loads centering. Chevrolet employs large bolt diameter and large weld beads in such a way that replacement parts slide in without messing up, and they are as rigid as those of the factory.

Chevrolet Rear Crossmember Parts and Q&A

Suspension Crossmember, Rear
15864493
Q: How to replace the Rear Crossmember in the rear suspension on Chevrolet Corvette?
A:
Begin the rear suspension crossmember replacement by lifting up and supporting the vehicle and removing both tire and wheel assemblies. First disconnect all wheel speed sensors from their harnesses along with coils from park brake cables and remove electrical connectors from esc Shock Absorber harnesses when present. Beginning the process you should remove the rear suspension position sensors and inner tie rod end studs from the Rear Crossmember and lower control arms from the crossmember. Lower control arms, rear suspension knuckles, and tie rods will require support before separating the transverse spring from its position. Install the j 42055 transmission support fixture (J 42055) on a transmission jack then position the fixture securely to support the transmission. Support the crossmember first by disconnecting electric harnesses and brake tubing followed by removing the lower mount nuts. Position a transmission jack underneath to hold the crossmember. Handle all tasks with hand tools only to unscrew the mounting nuts at the Rear Crossmember before extracting the component from the vehicle and discarding the mounting nuts. During installation align the crossmember dowel pins to the frame rails and transaxle mount studs to the crossmember before using new crossmember mounting nuts. Use only hand tools to install and torque new rear suspension crossmember mounting nuts to 110 n.m (81 lb ft). Remove the j 42055 transmission jack from both the transmission and crossmember before connecting all electrical harness retainers and brake pipe retainers to their respective locations on the crossmember. Position the transaxle mount lower nuts before installing the transverse spring and lower control arms and inner tie rod end studs with the rear suspension position sensors. Whenever possible connect electrical connectors to esc Shock Absorber harnesses if present and park brake cables to actuator levers in addition to wheel speed sensor harness connectors. After installation of tires and wheels complete vehicle lowering then perform measurements to adjust rear trim height before conducting a wheel alignment procedure.
Rear Crossmember
15207019
Q: How to replace the rear crossmember for the steering gear on Chevrolet SSR?
A:
You should first raise and support the vehicle to begin the replacement of the rear steering gear crossmember. Unbolt the rear mounting points of the rear steering gear crossmember as well as the rear mounting bolts on the front steering gear crossmember and carefully take the crossmember out from the vehicle. Align the rear steering gear crossmember with its mounting holes, put in the bolts, and tighten them to 50 N.m (37 lb ft). Following this, put in and tighten the rear mounting bolts for the front steering gear crossmember to 50 N.m (37 lb ft), then lower the vehicle.