How to service and repair the shift cable at the column shift control on Chevrolet Impala?

The automatic transaxle range selector cable retainer needs removal from the engine compartment stud before proceeding to detach the steering column trim panel. After detaching the automatic transaxle range selector cable it needs to be extracted through a dash hole while it is disconnected from both the shift control lever and manual shaft. Start the automatic transaxle range selector cable installation by directing it through the dash hole followed by correct cable routing and positioning then connect it to the manual shaft and shift control lever. Both the steering column trim panel and automatic transaxle range selector cable retainer should be attached to the engine compartment stud. The last step includes adjusting the transaxle side automatic transaxle range selector cable.

How to replace the automatic transmission shift cable on Chevrolet Impala?

The first step to substitute the automatic transmission range selector cable involves removing the air cleaner intake duct followed by detaching the cable from the wiring harness clip while also removing its cable retainer. The next step requires removal of the automatic transaxle range selector lever cable as well as its cable bracket. The removal of front floor console and pulling back carpeting becomes necessary because the cable requires access when floor console exists. First detach the cable retainer from the console shift control before removing the cable both from the control and its bracket. Remove the left knee bolster bracket before proceeding to disconnect the cable from the shift control lever. Move mechanics wire to pass the new cable into the cowl hole before removing the wire. Install the new cable to the shift control lever before putting back the left knee bolster bracket when working on a steering column shift control. The cable needs to be connected to both the console shift control bracket and the console shift control before installation of the cable retainer takes place. Reinstall both carpeting and front floor console while ensuring the cable moves according to the correct path. Begin by connecting the cable to the automatic transaxle range selector lever and the cable bracket and finally secure the cable retainer. Use the neutral position for the transaxle and shift control to join their cable ends through end fitting insertion until they snap securely. Use the adjuster clip to move the housing while guiding end fittings until complete clip depression locks the cable. Install the cable first followed by securing it to the wiring harness clip or strap or adjusting the cable after which re-install the air cleaner intake duct.

OEM Chevrolet Impala Shift Cable

Transmission Shift Cable

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

12 Shift Cables found

View related parts
Chevrolet Impala Shift Control Cable Part Number: 23274919
$51.73 MSRP: $77.00
You Save: $25.27 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly-Automatic Transmission Range Selector Lever
- Replaced by: 84145765
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015 Chevrolet Impala | LS, LT, LTZ | 4 Cyl 2.5 L GAS, 6 Cyl 3.6 L BI-FUEL, 6 Cyl 3.6 L FLEX
View related parts
Chevrolet Impala Shift Control Cable Part Number: 22856120
$28.51 MSRP: $43.01
You Save: $14.50 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly-Automatic Transmission Range Selector Lever; Cable, Transmission Shift Control Cable
- Replaces: 20836463
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2012-2013 Chevrolet Impala | LS, LT, LTZ, Police | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Impala Shift Control Cable Part Number: 20836465
$35.26 MSRP: $53.19
You Save: $17.93 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly-Automatic Transmission Range Selector Lever; Cable, Transmission Shift Control Cable
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2012-2013 Chevrolet Impala | LS, LT, LTZ, Police | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Impala Shift Control Cable Part Number: 84145766
$42.80 MSRP: $67.00
You Save: $24.20 (37%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly-Automatic Transmission Range Selector Lever; Cable, Transmission Shift Control Cable; Cable, Transmission Control Cable
- Replaces: 22955157, 22758167, 23274920, 23226826
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014 Chevrolet Impala | Eco, LS, LT, LTZ | 4 Cyl 2.4 L MILD HYBRID EV-GAS (MHEV), 4 Cyl 2.5 L GAS
View related parts
Chevrolet Impala Shift Control Cable Part Number: 84145765
$51.73 MSRP: $77.00
You Save: $25.27 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly-Automatic Transmission Range Selector Lever; Cable, Transmission Shift Control Cable; Cable, Transmission Control Cable
- Replaces: 23226825, 23274919
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 Chevrolet Impala | LS, LT, LTZ, Premier | 4 Cyl 2.5 L FLEX, 4 Cyl 2.5 L GAS, 6 Cyl 3.6 L BI-FUEL, 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Impala Shift Control Cable Part Number: 22758166
$11.91 MSRP: $17.96
You Save: $6.05 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable Assembly-Automatic Transmission Range Selector Lever; Cable, Transmission Shift Control Cable; Cable, Transmission Control Cable
- Replaces: 22955156
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014 Chevrolet Impala | LT, LTZ | 6 Cyl 3.6 L FLEX, 6 Cyl 3.6 L GAS
View related parts
Chevrolet Impala Shift Control Cable Part Number: 25940466
Product Specifications
- Other Name: Cable Assembly-Automatic Transmission Range Selector Lever; Cable, Transmission Shift Control Cable
- Replaces: 25859097
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2011 Chevrolet Impala | 50th Anniversary Edition, LS, LT, LTZ, Police, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Impala Shift Control Cable Part Number: 25940464
Product Specifications
- Other Name: Cable Assembly-Automatic Transmission Range Selector Lever; Cable, Transmission Shift Control Cable
- Replaces: 25807291
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2007 Chevrolet Impala | LS, LT, LTZ, Police, SS | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Impala Shift Control Cable Part Number: 19152621
Product Specifications
- Other Name: Cable Kit, Automatic Transmission Range Selector Lever; Cable Kit, Transmission Shift Control Cable
- Replaces: 88996494
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2007 Chevrolet Impala | Base, LS, LS Sport, LT, LTZ, Police, SS | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 5.3 L GAS
View related parts
Chevrolet Impala Shift Control Cable Part Number: 19152619
Product Specifications
- Other Name: Cable Kit, Automatic Transmission Range Selector Lever; Cable Kit, Transmission Shift Control Cable
- Replaces: 88996495
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2005 Chevrolet Impala | Base, LS, LS Sport, Police, SS | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Impala Shift Control Cable Part Number: 12458110
Product Specifications
- Other Name: Cable Kit, Automatic Transmission Range Selector Lever; Cable Kit, Transmission Shift Control Cable
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2001 Chevrolet Impala | Base, LS | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS
View related parts
Chevrolet Impala Shift Control Cable Part Number: 12458109
Product Specifications
- Other Name: Cable Kit, Automatic Transmission Range Selector Lever; Cable Kit, Transmission Shift Control Cable
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2001 Chevrolet Impala | Base, LS | 6 Cyl 3.4 L GAS, 6 Cyl 3.8 L GAS

Chevrolet Impala Shift Cable

Want to cut long-term maintenance and repair costs? Choose OEM Shift Cable. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Impala parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Impala Shift Cable includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

Chevrolet Impala Shift Cable Parts and Q&A

Shift Control Cable
12458109
Q: How to service and repair the shift cable at the column shift control on Chevrolet Impala?
A:
The automatic transaxle range selector cable retainer needs removal from the engine compartment stud before proceeding to detach the steering column trim panel. After detaching the automatic transaxle range selector cable it needs to be extracted through a dash hole while it is disconnected from both the shift control lever and manual shaft. Start the automatic transaxle range selector cable installation by directing it through the dash hole followed by correct cable routing and positioning then connect it to the manual shaft and shift control lever. Both the steering column trim panel and automatic transaxle range selector cable retainer should be attached to the engine compartment stud. The last step includes adjusting the transaxle side automatic transaxle range selector cable.
Shift Control Cable
19152621
Q: How to replace the automatic transmission shift cable on Chevrolet Impala?
A:
The first step to substitute the automatic transmission range selector cable involves removing the air cleaner intake duct followed by detaching the cable from the wiring harness clip while also removing its cable retainer. The next step requires removal of the automatic transaxle range selector lever cable as well as its cable bracket. The removal of front floor console and pulling back carpeting becomes necessary because the cable requires access when floor console exists. First detach the cable retainer from the console shift control before removing the cable both from the control and its bracket. Remove the left knee bolster bracket before proceeding to disconnect the cable from the shift control lever. Move mechanics wire to pass the new cable into the cowl hole before removing the wire. Install the new cable to the shift control lever before putting back the left knee bolster bracket when working on a steering column shift control. The cable needs to be connected to both the console shift control bracket and the console shift control before installation of the cable retainer takes place. Reinstall both carpeting and front floor console while ensuring the cable moves according to the correct path. Begin by connecting the cable to the automatic transaxle range selector lever and the cable bracket and finally secure the cable retainer. Use the neutral position for the transaxle and shift control to join their cable ends through end fitting insertion until they snap securely. Use the adjuster clip to move the housing while guiding end fittings until complete clip depression locks the cable. Install the cable first followed by securing it to the wiring harness clip or strap or adjusting the cable after which re-install the air cleaner intake duct.