How to replace the Crankshaft Position Sensor on Chevrolet Corvette?

A replacement of the Crankshaft Position Sensor begins with disconnecting the vehicle's negative Battery Cable. Lift the vehicle while removing the Starter from its position. After disconnecting the crankshaft position (CKP) sensor electrical connector you must thoroughly clean the ckp area so no contaminants can enter the engine. Start by removing both the retaining bolt and sensor of the crankshaft positioning device. Reposition the ckp sensor into place followed by tightening a 25 n.m (18 lb ft) torque bolt. Lower the vehicle after reattaching the negative Battery Cable but before returning the Starter. Then reconnect the ckp sensor electrical connector. Complete the transmitter programming followed by executing the ckp system variation learn procedure.

How to Service the Crankshaft Position Sensor on Chevrolet Corvette?

First disconnect the negative Battery Cable when servicing Crankshaft Position Sensor. Lift the car and uninstall the Starter. Hunt down the crankshaft position (CKP) sensor electrical link and unplug the link, being attentive to clean the area close by the ckp to obstruct debris from infiltrating the engine. Disengage the ckp sensor retaining bolt followed by the ckp sensor itself. Put the ckp sensor back into position and install the retaining bolt, tightening it to 25nm (18lb ft). Reattach the ckp sensor electrical connector, the Starter fixed back, the vehicle lowered back, and the negative Battery Cable reattached. Finally, idle learn procedure and program the transmitters if necessary.

OEM Chevrolet Corvette Crankshaft Position Sensor

Engine Crankshaft Position Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

9 Crankshaft Position Sensors found

View related parts
Chevrolet Corvette Crankshaft Position Sensor Part Number: 12703627
$60.13 MSRP: $107.38
You Save: $47.25 (44%)
ADD TO CART
Product Specifications
- Other Name: Sensor Assembly-Crankshaft Position; Crankshaft Sensor; Sensor, Distributor (Also Knock Sensor)
- Replaces: 12585546
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2013 Chevrolet Corvette | 427, 427 Limited Edition Z06, Base, Grand Sport, Z06, Z06 Carbon, ZR1 | 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 7.0 L GAS
View related parts
Chevrolet Corvette Crankshaft Position Sensor Part Number: 12674702
$44.84 MSRP: $91.06
You Save: $46.22 (51%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor Assembly-Crankshaft Position; Camshaft Position Sensor; Crankshaft Sensor; Sensor, Distributor (Also Knock Sensor)
- Replaces: 12627185, 12632872
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2023-2024 Chevrolet Corvette | Z06 | 8 Cyl 5.5 L GAS
View related parts
Chevrolet Corvette Crankshaft Position Sensor Part Number: 12669636
$28.91 MSRP: $54.30
You Save: $25.39 (47%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor Assembly-Crankshaft Position; Crankshaft Sensor; Sensor, Distributor (Also Knock Sensor)
- Replaces: 12623094
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2014-2024 Chevrolet Corvette | E-Ray, Grand Sport, Stingray, Z06, ZR1 | 8 Cyl 6.2 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Crankshaft Position Sensor Part Number: 12560228
$66.20 MSRP: $119.82
You Save: $53.62 (45%)
ADD TO CART
Product Specifications
- Other Name: Sensor, Distributor (Also Knock Sensor); Engine Camshaft Position Sensor; Crankshaft Sensor
- Replaces: 12555566
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2005 Chevrolet Corvette | 50th Anniversary Edition, 50th Anniversary Edition Pace Car, Base, Indianapolis 500 Pace Car, Z06 | 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L GAS
View related parts
Chevrolet Corvette Crankshaft Position Sensor Part Number: 12667201
$24.62 MSRP: $44.56
You Save: $19.94 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor Assembly-Crankshaft Position; Crankshaft Sensor; Sensor, Distributor (Also Knock Sensor)
- Replaced by: 12712848
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2022 Chevrolet Corvette | Stingray | 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Crankshaft Position Sensor Part Number: 19170837
Product Specifications
- Other Name: Sensor Assembly, Crankshaft Position; Crankshaft Sensor; Sensor, Distributor (Also Knock Sensor)
- Replaces: 10456534, 10456237
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996 Chevrolet Corvette | Base, Collector's Edition, Grand Sport | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Knock Sensor Part Number: 10456287
Product Specifications
- Other Name: Sensor, Distributor (Also Knock Sensor); Control Module; ESC Sensor; Sensor
- Replaces: 10456017
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996 Chevrolet Corvette | Base | 8 Cyl 5.7 L GAS
View related parts
Chevrolet Corvette Crankshaft Position Sensor Part Number: 12601389
$35.48 MSRP: $63.36
You Save: $27.88 (44%)
Product Specifications
- Other Name: Sensor, Distributor (Also Knock Sensor); Engine Crankshaft Position Sensor; Crankshaft Sensor
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009-2013 Chevrolet Corvette | ZR1 | 8 Cyl 6.2 L GAS
View related parts
Chevrolet Corvette Crankshaft Position Sensor Part Number: 10457661
Product Specifications
- Other Name: Sensor Assembly-Crankshaft Position; Engine Crankshaft Position Sensor; Sensor, Distributor (Also Knock Sensor)
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1995 Chevrolet Corvette | 40th Anniversary Edition, Base, Indianapolis 500 Pace Car, ZR-1 | 8 Cyl 5.7 L GAS

Chevrolet Corvette Crankshaft Position Sensor

Want to cut long-term maintenance and repair costs? Choose OEM Crankshaft Position Sensor. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Corvette parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Corvette Crankshaft Position Sensor includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

The Crankshaft Position Sensor is a type of electronic Chevrolet corvette component which measures the phase of the engine and sends impulses to the enginge management. This sensor is very important in the management of fuel injection, ignition time, and other related operations of the engine. Normally located on the main crank pulley, flywheel, camshaft or the crankshaft directly, the sensor usually came in several forms; Inductive, Hall Effect, Magnetoresistive and optical sensor form. With defective Crankshaft Position Sensor, there could be problems in starting the car and some problems with the functioning of the Chevrolet Corvette engine hence is crucial for proper engine operation.

Chevrolet Corvette Crankshaft Position Sensor Parts and Q&A

Crankshaft Position Sensor
12703627
Q: How to replace the Crankshaft Position Sensor on Chevrolet Corvette?
A:
A replacement of the Crankshaft Position Sensor begins with disconnecting the vehicle's negative Battery Cable. Lift the vehicle while removing the Starter from its position. After disconnecting the crankshaft position (CKP) sensor electrical connector you must thoroughly clean the ckp area so no contaminants can enter the engine. Start by removing both the retaining bolt and sensor of the crankshaft positioning device. Reposition the ckp sensor into place followed by tightening a 25 n.m (18 lb ft) torque bolt. Lower the vehicle after reattaching the negative Battery Cable but before returning the Starter. Then reconnect the ckp sensor electrical connector. Complete the transmitter programming followed by executing the ckp system variation learn procedure.
Crankshaft Position Sensor
12560228
Q: How to Service the Crankshaft Position Sensor on Chevrolet Corvette?
A:
First disconnect the negative Battery Cable when servicing Crankshaft Position Sensor. Lift the car and uninstall the Starter. Hunt down the crankshaft position (CKP) sensor electrical link and unplug the link, being attentive to clean the area close by the ckp to obstruct debris from infiltrating the engine. Disengage the ckp sensor retaining bolt followed by the ckp sensor itself. Put the ckp sensor back into position and install the retaining bolt, tightening it to 25nm (18lb ft). Reattach the ckp sensor electrical connector, the Starter fixed back, the vehicle lowered back, and the negative Battery Cable reattached. Finally, idle learn procedure and program the transmitters if necessary.