How should you safely drain oil from gas charged shock absorbers on Cadillac XLR?

Personal injury could occur when you remove the snap ring from inside the top of the tube since gas charged shock absorbers contain high pressure gas that will propel contents with extreme force. Wear protective safety glasses while drilling the shock absorber tube since centerpunching and avoid any damage to this tube structure. Use a centerpunch to create a 10 mm (0.4 inch) indentation on the tube bottom at a point 10 mm (0.4 inches) above the bottom. Position the shock absorber rod fully straight while mounting the device onto a vise for horizontal placement. Drill a 5 mm (3/16 inch) hole at the centerpunch mark in the shock absorber to let gas or gas/oil mixture escape while containment occurs through shop towels. Drilling the second hole at the middle indentation requires repeating the process of centerpunching followed by using a 5 mm (3/16 inch) drill bit. Shop towels must contain the escaping oil during this operation. Complete removal of oil from the shock absorber can be achieved by keeping it horizontal in the drain pan with holes facing down while moving the rod through the tube.

How to replace the rear shock absorber (W/F55) on Cadillac XLR?

The first step to replace w/f55 rear shock absorbers includes vehicle elevation along with wheel and tire removal. The rear shock electronic suspension control (ESC) harness connector needs removal from the upper shock tower clip together with the harness pigtail. The installation requires removal of both the lower Control Arm retaining bolt at the Shock Absorber and all the upper Shock Absorber mounting bolts. The Shock Absorber removal process requires detachment of the outer tie rod from the suspension knuckle while properly guiding the esc pigtail as well as connector through the upper shock tower. Remove the upper insulator retainer and insulator that exists on the Shock Absorber. Install the Shock Absorber by connecting the upper insulator retainer and insulator while maintaining the esc connector inside and white paint mark facing outwards at 180 degrees between the bracket and esc connector. The Shock Absorber must be installed to the shock tower and lower Control Arm with special attention toward the esc pigtail and connector. When installing the Shock Absorber upper bolts use 30 n.m (22 lb ft) torque putting only force on the bolt instead of the nut to prevent it from breaking. Use the lower Shock Absorber mounting bolt to secure the unit by tightening its retaining nut to 145 n.m (107 lb ft). Reestablish connections between the outer tie rod and suspension knuckle along with both harness pigtail attachment to the upper shock tower clip and esc harness connector to the rear shock. Reposition the tire together with the wheel assembly before lowering down the vehicle.

OEM Cadillac XLR Shock Absorber

Suspension Shock Absorber

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

14 Shock Absorbers found

View related parts
Cadillac XLR Shock Absorber Part Number: 19302775
$525.19 MSRP: $1019.30
You Save: $494.11 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Strut Kit, Shock; Shock
- Position: Front
- Replaces: 19178739, 19259307
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008 Cadillac XLR | Base, Platinum, V | 8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS
View related parts
Cadillac XLR Shock Absorber Part Number: 19302774
$561.63 MSRP: $1099.62
You Save: $537.99 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Strut Kit, Shock; Shock
- Position: Front
- Replaces: 19259306, 19207674
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2009 Cadillac XLR | Platinum, V | 8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS
View related parts
Cadillac XLR Shock Absorber Part Number: 19302790
$540.07 MSRP: $1048.18
You Save: $508.11 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Absorber Kit, Front And Rear Suspension; Shock; Absorber Kit, Shock
- Position: Front
- Replaces: 88952527
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2007 Cadillac XLR | Base, V | 8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS
View related parts
Cadillac XLR Shock Absorber, Rear Driver Side Part Number: 19431692
$525.90 MSRP: $1029.66
You Save: $503.76 (49%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Absorber Kit, Rear Shock; Shock; Absorber Kit, Front And Rear Suspension
- Position: Rear Driver Side
- Replaces: 19302792, 88952529
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2005 Cadillac XLR | Base | 8 Cyl 4.6 L GAS
View related parts
Cadillac XLR Shock Absorber, Rear Passenger Side Part Number: 19431691
$527.90 MSRP: $1024.56
You Save: $496.66 (49%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Absorber Kit, Rear Shock; Shock; Absorber Kit, Front And Rear Suspension
- Position: Rear Passenger Side
- Replaces: 19302791, 88952528
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2005 Cadillac XLR | Base | 8 Cyl 4.6 L GAS
View related parts
Cadillac XLR Shock Absorber, Rear Driver Side Part Number: 19431688
$508.65 MSRP: $995.88
You Save: $487.23 (49%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Absorber Assembly, Rear Shock; Shock; Absorber, Front And Rear Suspension; Absorber, Shock
- Position: Rear Driver Side
- Replaces: 19302781, 22784743, 19177206
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2009 Cadillac XLR | Base, Platinum | 8 Cyl 4.6 L GAS
View related parts
Cadillac XLR Shock Absorber, Passenger Side Part Number: 19431687
$573.40 MSRP: $1037.82
You Save: $464.42 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Absorber, Shock; Shock; Absorber, Front And Rear Suspension
- Position: Passenger Side
- Replaces: 22784741, 19177205, 19302779
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2009 Cadillac XLR | Base, Platinum, V | 8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS
View related parts
Cadillac XLR Shock Absorber Part Number: 19302772
$533.06 MSRP: $1043.68
You Save: $510.62 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Absorber Kit, Front And Rear Suspension; Shock
- Position: Front
- Replaces: 19181113
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2009 Cadillac XLR | Base, Platinum, V | 8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS
View related parts
Cadillac XLR Shock Absorber, Rear Passenger Side Part Number: 19302794
Product Specifications
- Other Name: Absorber Kit, Rear Shock; Shock; Absorber Kit, Front And Rear Suspension
- Position: Rear Passenger Side
- Replaces: 88967434
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2007 Cadillac XLR | V | 8 Cyl 4.4 L GAS
View related parts
Cadillac XLR Shock Absorber, Rear Passenger Side Part Number: 19302770
Product Specifications
- Other Name: Absorber Kit, Rear Shock; Shock; Absorber Kit, Front And Rear Suspension
- Position: Rear Passenger Side
- Replaces: 19177203
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2009 Cadillac XLR | Base, Platinum, V | 8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS
View related parts
Cadillac XLR Shock Absorber, Rear Passenger Side Part Number: 19431690
$517.10 MSRP: $931.72
You Save: $414.62 (45%)
Product Specifications
- Other Name: Absorber Kit, Rear Shock; Shock; Absorber Kit, Front And Rear Suspension; Absorber Kit, Shock
- Position: Rear Passenger Side
- Replaces: 19302789, 88952526
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2007 Cadillac XLR | Base | 8 Cyl 4.6 L GAS
View related parts
Cadillac XLR Shock Absorber, Rear Driver Side Part Number: 19431689
$536.53 MSRP: $966.72
You Save: $430.19 (45%)
Product Specifications
- Other Name: Absorber Kit, Rear Shock; Shock; Absorber Kit, Front And Rear Suspension; Absorber Kit, Shock
- Position: Rear Driver Side
- Replaces: 19302788, 88952525
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2007 Cadillac XLR | Base | 8 Cyl 4.6 L GAS
View related parts
Cadillac XLR Shock Absorber, Rear Driver Side Part Number: 19177204
Product Specifications
- Other Name: Absorber Kit, Rear Shock; Shock
- Position: Rear Driver Side
- Replaced by: 19302771
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2008-2009 Cadillac XLR | V | 8 Cyl 4.4 L GAS
View related parts
Cadillac XLR Shock Absorber, Rear Driver Side Part Number: 19302793
Product Specifications
- Other Name: Absorber Kit, Rear Shock; Shock; Absorber Kit, Front And Rear Suspension
- Position: Rear Driver Side
- Replaces: 88967432
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2007 Cadillac XLR | V | 8 Cyl 4.4 L GAS

Cadillac XLR Shock Absorber

Want to cut long-term maintenance and repair costs? Choose OEM Shock Absorber. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Cadillac XLR parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Cadillac XLR Shock Absorber includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

A Shock Absorber is an important element of the automobile's suspension mechanism necessary for an XLR an emanation of Cadillac's flagship- Roadster. Intended to reduce and minimize most of the shock impulses that may affect the car, the Shock Absorber improves the car's ability to provide a smooth ride even in tough ground conditions. Due to the variants of the Shock Absorber, which includes twin-tube and mono-tube, drivers can have their preferred style and road situation. The twin-tube shocks are durable, but the mono-tube ones are better in heat management and performance; that's why they are used for adaptive response with technologies like PSD and MR dampers. Adaptability with different Cadillac XLR models guarantees DWG drivers continue to preserve Cadillac XLR's suspension system, which, in turn, improves output and security. The Cadillac XLR manufactured between 2003 and 2009 is famous for having such novelties as an electric roof and Magnetic Ride Control suspension, which complemented the Shock Absorber. The car has a really potent 320 Hp V8 Northstar engine and it is supported by a good suspension system that Cadillac named the XLR Shock Absorber. It can also be noted that enhancing the performance and comfort of Shock Absorber puts its image in the automotive market even more and is therefore reflecting the luxury and reliability that drivers are looking for.

Cadillac XLR Shock Absorber Parts and Q&A

Shock Absorber
19302790
Q: How should you safely drain oil from gas charged shock absorbers on Cadillac XLR?
A:
Personal injury could occur when you remove the snap ring from inside the top of the tube since gas charged shock absorbers contain high pressure gas that will propel contents with extreme force. Wear protective safety glasses while drilling the shock absorber tube since centerpunching and avoid any damage to this tube structure. Use a centerpunch to create a 10 mm (0.4 inch) indentation on the tube bottom at a point 10 mm (0.4 inches) above the bottom. Position the shock absorber rod fully straight while mounting the device onto a vise for horizontal placement. Drill a 5 mm (3/16 inch) hole at the centerpunch mark in the shock absorber to let gas or gas/oil mixture escape while containment occurs through shop towels. Drilling the second hole at the middle indentation requires repeating the process of centerpunching followed by using a 5 mm (3/16 inch) drill bit. Shop towels must contain the escaping oil during this operation. Complete removal of oil from the shock absorber can be achieved by keeping it horizontal in the drain pan with holes facing down while moving the rod through the tube.
Shock Absorber, Rear Passenger Side
19431690
Q: How to replace the rear shock absorber (W/F55) on Cadillac XLR?
A:
The first step to replace w/f55 rear shock absorbers includes vehicle elevation along with wheel and tire removal. The rear shock electronic suspension control (ESC) harness connector needs removal from the upper shock tower clip together with the harness pigtail. The installation requires removal of both the lower Control Arm retaining bolt at the Shock Absorber and all the upper Shock Absorber mounting bolts. The Shock Absorber removal process requires detachment of the outer tie rod from the suspension knuckle while properly guiding the esc pigtail as well as connector through the upper shock tower. Remove the upper insulator retainer and insulator that exists on the Shock Absorber. Install the Shock Absorber by connecting the upper insulator retainer and insulator while maintaining the esc connector inside and white paint mark facing outwards at 180 degrees between the bracket and esc connector. The Shock Absorber must be installed to the shock tower and lower Control Arm with special attention toward the esc pigtail and connector. When installing the Shock Absorber upper bolts use 30 n.m (22 lb ft) torque putting only force on the bolt instead of the nut to prevent it from breaking. Use the lower Shock Absorber mounting bolt to secure the unit by tightening its retaining nut to 145 n.m (107 lb ft). Reestablish connections between the outer tie rod and suspension knuckle along with both harness pigtail attachment to the upper shock tower clip and esc harness connector to the rear shock. Reposition the tire together with the wheel assembly before lowering down the vehicle.