How to replace an emblem/nameplate on the front fender on Cadillac XLR?

You must protect the panel surface from damage when replacing a front fender emblem/nameplate. Place alignment marks on top with tape before installation. Use the J 25070 (J 25070) at 152 mm (6 in) distance to heat the emblem/nameplate in a circular motion for 30 seconds. Use a plastic tool with a flat end to take the emblem/nameplate off the panel surface. Use a lint-free cloth to wipe the area where the emblem/nameplate will be installed and then clean it with VMP naphtha or a 50/50 alcohol-water solution before completely drying. Apply tape first when no marking exists and place the XLR emblem/nameplate 108 mm (4.25 in) behind the fender edge along with 305 mm (12 in) below its bottom border. Heat the mounting area to 80-105°F with J 25070 (J 25070) tool and maintain the emblem/nameplate temperature at 85-90°F. You should not handle the adhesive surface of the emblem/nameplate before removing the back liner. Place the emblem at its marked location and push the part evenly into the mounting surface so it sticks well. Take off the film protection on the mounting area.

How to replace the rear compartment lid emblem/nameplate on a V8 on Cadillac XLR?

Before replacing the V8 rear compartment lid emblem/nameplate you must tape the mounting surface and take alignment marks for easy installation. Use J 25070 heat gun to heat the emblem/nameplate in circular motions for 30 seconds at a 152 mm (6 in) distance from the surface. Quintessential flat blade made of plastic to pry off the emblem/nameplate from its panel surface. Set up the emblem/nameplate installation site between 85 and 90 degrees Fahrenheit. Avoid handling the adhesive side of the nameplate. First remove the protective film at the back of the emblem/nameplate then apply J 25070 heat gun at 27-41°C (80-105°F) to warm up the installation area. Place the V8 Northstar emblem to the left side of the driver area at 67 mm (2.6 in) from the edge and 86 mm (3.4 in) from the bottom of the rear compartment lid. Position the XLR emblem on the passenger side 2.4 inches from the right edge and 3.4 inches from the bottom of the rear compartment lid. Push down evenly on all parts of the emblem to evenly attach it to the mounting point before lifting off the covering tape.

OEM Cadillac XLR Emblem

Badge

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

13 Emblems found

View related parts
Cadillac XLR Center Cap, Black Part Number: 9596629
$47.99 MSRP: $68.66
You Save: $20.67 (31%)
ADD TO CART
Product Specifications
- Other Name: Cap-Hub Polished 19" Wheels *Black Backgr; Wheel Center Cap; Hub Cap; Emblem; Emblem, Wheel Cover Appearance; Cap, Wheel - Front And Rear; Cap, Wheel Trim
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2009 Cadillac XLR | Base, Platinum, V | 8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS
View related parts
Cadillac XLR Emblem Part Number: 84689784
$11.42 MSRP: $17.00
You Save: $5.58 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Emblem, Front Side Door; Decal; Nameplate; Emblem, Cab, Load Carrier, Rear End, Door, Quarter Panel, Fender, Rocker Panel, Side Step.
- Replaces: 15223483, 15223484
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2009 Cadillac XLR | Base, Platinum, V | 8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS
View related parts
Cadillac XLR Nameplate, Rear Part Number: 10387855
Product Specifications
- Other Name: Plate, Rear End Panel And Tailgate; Emblem, End Gate And Rear Door Decoration; Emblem,Rear End Panel And Tailgate; Plate,Rear End Panel And Tailgate
- Position: Rear
- Replaces: 10372469, 25739124, 25762472
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2009 Cadillac XLR | Base, Platinum, V | 8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS
View related parts
Cadillac XLR Emblem Part Number: 10334204
Product Specifications
- Other Name: Emblem, Tail Lamp
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2009 Cadillac XLR | Base, Platinum, V | 8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS
View related parts
Cadillac XLR Emblem, Front Part Number: 10334202
Product Specifications
- Other Name: Emblem, Radiator Grille And Front End Ornamentation
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2008 Cadillac XLR | Base, Platinum | 8 Cyl 4.6 L GAS
View related parts
Cadillac XLR Emblem, Front Part Number: 22985036
$83.64 MSRP: $124.49
You Save: $40.85 (33%)
Product Specifications
- Other Name: Emblem Assembly-Front Grille; Emblem, Radiator Grille And Front End Ornamentation
- Position: Front
- Replaces: 20824266, 25795247, 22860587
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2009 Cadillac XLR | Platinum, V | 8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS
View related parts
Cadillac XLR Emblem, Front Part Number: 15851892
$94.51 MSRP: $140.66
You Save: $46.15 (33%)
Product Specifications
- Other Name: Emblem, Front Fender Name; Nameplate; Emblem,Rear End Panel And Tailgate; Plate,Rear End Panel And Tailgate; Emblem, Front Side Door
- Position: Front
- Replaces: 25754866
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2009 Cadillac XLR | V | 8 Cyl 4.4 L GAS
View related parts
Cadillac XLR Nameplate, Front Part Number: 15810646
$63.71 MSRP: $94.82
You Save: $31.11 (33%)
Product Specifications
- Other Name: Emblem, Front Side Door
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2009 Cadillac XLR | V | 8 Cyl 4.4 L GAS
View related parts
Cadillac XLR Emblem Part Number: 25757717
Product Specifications
- Other Name: Emblem, Bumper/Fascia
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2008 Cadillac XLR | V | 8 Cyl 4.4 L GAS
View related parts
Cadillac XLR Emblem, Front Part Number: 15233934
Product Specifications
- Other Name: Emblem, Radiator Grille And Front End Ornamentation
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2006-2008 Cadillac XLR | V | 8 Cyl 4.4 L GAS
View related parts
Cadillac XLR Nameplate, Rear Part Number: 10334040
Product Specifications
- Other Name: Plate, Rear End Panel And Tailgate; Plate,Rear End Panel And Tailgate
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2008 Cadillac XLR | Base, Platinum, V | 8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS
View related parts
Cadillac XLR Emblem, Front Part Number: 10333719
Product Specifications
- Other Name: Emblem, Radiator Grille And Front End Ornamentation
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2008 Cadillac XLR | Base, Platinum | 8 Cyl 4.6 L GAS
View related parts
Cadillac XLR Emblem Part Number: 10291759
$5.34 MSRP: $7.95
You Save: $2.61 (33%)
Product Specifications
- Other Name: Emblem, Radio Auxiliary Speakers
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2004-2009 Cadillac XLR | Base, Platinum, V | 8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS

Cadillac XLR Emblem

Want to cut long-term maintenance and repair costs? Choose OEM Emblem. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Cadillac XLR parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Cadillac XLR Emblem includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

Through its emblem Cadillac XLR represents both high performance capabilities and luxurious qualities in order to demonstrate brand excellence in the automotive industry. Various implementations of this emblem can be seen as both hood ornaments and flat tape attachments on the hood and trunk while serving as essential elements for Cadillac XLR brand recognition. Customers recognize the Cadillac XLR as a premiere fleet model because it features a folding roof mechanism with Magnetic Ride Control suspension and offers an outstanding V8 Northstar powertrain. The XLR emblem represents Cadillac while improving the vehicle's efficiency and safety aspects to demonstrate the manufacturer's commitment to innovative designs. Unlike its appearance the emblem maintains its core purpose of preserving Cadillac brand history across multiple XLR vehicle models. The emblem shows flexibility in design elements and materials yet its main purpose is to serve as a legacy symbol for Cadillac. The manufacturer XLR stands out from its competitors because it combines special features which include heated automotive seats alongside cooled leather seats and superior horsepower from its supercharged version with advanced navigation systems. Each model of brand model sports its distinctive emblem that defines the automaker roadster leadership through distinctive style together with meaningful brand values delivering outstanding performance and reliability.

Cadillac XLR Emblem Parts and Q&A

Emblem
10291759
Q: How to replace an emblem/nameplate on the front fender on Cadillac XLR?
A:
You must protect the panel surface from damage when replacing a front fender emblem/nameplate. Place alignment marks on top with tape before installation. Use the J 25070 (J 25070) at 152 mm (6 in) distance to heat the emblem/nameplate in a circular motion for 30 seconds. Use a plastic tool with a flat end to take the emblem/nameplate off the panel surface. Use a lint-free cloth to wipe the area where the emblem/nameplate will be installed and then clean it with VMP naphtha or a 50/50 alcohol-water solution before completely drying. Apply tape first when no marking exists and place the XLR emblem/nameplate 108 mm (4.25 in) behind the fender edge along with 305 mm (12 in) below its bottom border. Heat the mounting area to 80-105°F with J 25070 (J 25070) tool and maintain the emblem/nameplate temperature at 85-90°F. You should not handle the adhesive surface of the emblem/nameplate before removing the back liner. Place the emblem at its marked location and push the part evenly into the mounting surface so it sticks well. Take off the film protection on the mounting area.
Nameplate, Rear
10387855
Q: How to replace the rear compartment lid emblem/nameplate on a V8 on Cadillac XLR?
A:
Before replacing the V8 rear compartment lid emblem/nameplate you must tape the mounting surface and take alignment marks for easy installation. Use J 25070 heat gun to heat the emblem/nameplate in circular motions for 30 seconds at a 152 mm (6 in) distance from the surface. Quintessential flat blade made of plastic to pry off the emblem/nameplate from its panel surface. Set up the emblem/nameplate installation site between 85 and 90 degrees Fahrenheit. Avoid handling the adhesive side of the nameplate. First remove the protective film at the back of the emblem/nameplate then apply J 25070 heat gun at 27-41°C (80-105°F) to warm up the installation area. Place the V8 Northstar emblem to the left side of the driver area at 67 mm (2.6 in) from the edge and 86 mm (3.4 in) from the bottom of the rear compartment lid. Position the XLR emblem on the passenger side 2.4 inches from the right edge and 3.4 inches from the bottom of the rear compartment lid. Push down evenly on all parts of the emblem to evenly attach it to the mounting point before lifting off the covering tape.