How to service and repair the Brake Disc using the J41013 and J42450-A kits on Cadillac Seville?

You need both the j41013 disc resurfacing kit (J41013) and the j42450-a Wheel Hub resurfacing kit (J42450-A) to work on your Brake Disc. Start by removing all signs of rust or corrosion from the hub/axle flange using the j42450-a tool before cleaning both surfaces of the Brake Disc and hub/axle flange with the j41013 equipment. Check the surfaces for any unwanted particles that may affect the repair. Install the Brake Disc on the brake lathe as directed by the manufacturer while also making sure clean attachment and adapter components are in place. Fasten vibration dampening equipment first and run the brake lathe while gradually bringing in the grinding tools until they touch only the disc surfaces. Inspect the witness mark on the disc; when it properly extends over three-fourths of both friction surface edges the disc is correctly attached to the brake lathe. If not, re-mount it. Perform the lathe renovation task according to the manufacturer manual and check the disc layers after each trim. The disc has to be replaced if its minimum allowable thickness remains unsupported during refinishing. Apply 120 grit aluminum oxide sandpaper at the indicated speed to finish the disc as recommended by the tool manufacturer. Non-directional finishing tools require 120 grit sandpaper while sanding blocks need 150 grit sandpaper for the process. After applying the finish use denatured alcohol or brake cleaner to wipe clean all brake friction parts. Take the Brake Disc off the lathe and measure its collected llo pattern to keep disc brakes operating at their best while you adjust the results when they exceed the set requirements.

How to replace the front brake disc on Cadillac Seville?

Start Brake Disc replacement by taking off the tire and wheel unit first. Secure the brake caliper always with mechanic's wire whenever you detach it from its mount to keep hydraulic brake hose sealed because improper removal and mounting could break the seal and leak brake fluid. Before continuing you need to take out the brake caliper from its mounting bracket without disconnecting the hydraulic brake flexible hose. Additionally you should remove the Brake Caliper Bracket assembly. Record the disc position on the hub before taking it off. The Brake Disc installation success depends on eliminating all contaminants from both wheel bearing flange and disc contact areas to keep lateral runout and brake vibration under control. Apply the rotor resurfacing kit (J 41013) to wash off rust from both the wheel flange and wheel hub resurfacing kit (J 42450-A) to clean rust from the wheel hub area. Put the Brake Disc on the wheel studs on top of the wheel bearing flange then add the Brake Caliper Bracket assembly and attach the brake caliper to it. Reposition the tire unit at its original location.

OEM Cadillac Seville Brake Disc

Disc Rotor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

11 Brake Discs found

View related parts
Cadillac Seville Brake Rotor, Front Part Number: 19174917
$50.14 MSRP: $89.54
You Save: $39.40 (44%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Rotor Assembly, Front Brake; Disc Brake Hardware Kit; Rotor; Rotor, Front And Rear Wheel Brake
- Position: Front
- Replaces: 01642177, 18060207, 1642177, 18027718
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1991 Cadillac Seville | Base, Elegante, STS | 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac Seville Rotor Part Number: 88964102
$124.37 MSRP: $223.07
You Save: $98.70 (45%)
Product Specifications
- Other Name: Rotor, Front Brake; Disc Brake Hardware Kit; Brake Rotor; Rotor, Front And Rear Wheel Brake
- Position: Front
- Replaces: 18060686
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2003-2004 Cadillac Seville | SLS, STS | 8 Cyl 4.6 L GAS
View related parts
Cadillac Seville Rotor, Front Part Number: 19202731
Product Specifications
- Other Name: Rotor, Front Brake; Disc Brake Hardware Kit; Brake Rotor; Rotor, Front And Rear Wheel Brake
- Position: Front
- Replaces: 18060230, 18060640, 18060240, 19152695, 18021015, 18026591
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-2004 Cadillac Seville | SLS, STS | 8 Cyl 4.6 L GAS
View related parts
Cadillac Seville Brake Rotor, Front Part Number: 18060226
Product Specifications
- Other Name: Rotor Assembly, Front Brake; Disc Brake Hardware Kit; Rotor; Rotor, Front And Rear Wheel Brake
- Position: Front
- Replaces: 18018122
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1987 Cadillac Seville | Base, Elegante | 8 Cyl 4.1 L GAS
View related parts
Cadillac Seville Rotor Part Number: 18040482
Product Specifications
- Other Name: Rotor, Front And Rear Wheel Brake; Brake Rotor
- Position: Rear
- Replaced by: 88967261
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2004 Cadillac Seville | SLS, STS | 8 Cyl 4.6 L GAS
View related parts
Cadillac Seville Rotor Part Number: 88967261
Product Specifications
- Other Name: Rotor, Front And Rear Wheel Brake; Brake Rotor
- Position: Rear
- Replaces: 18023592, 18040482
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2004 Cadillac Seville | SLS, STS | 8 Cyl 4.6 L GAS
View related parts
Cadillac Seville Brake Rotor Part Number: 25526230
Product Specifications
- Other Name: Rotor; Rotor, Front And Rear Wheel Brake
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1991 Cadillac Seville | Base, Elegante, STS | 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac Seville Rotor, Front Part Number: 18060235
Product Specifications
- Other Name: Rotor, Front Brake; Disc Brake Hardware Kit; Brake Rotor; Rotor, Front And Rear Wheel Brake
- Position: Front
- Replaces: 18021769, 18018903
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1996 Cadillac Seville | Base, SLS, STS | 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac Seville Rotor, Rear Part Number: 18021768
Product Specifications
- Other Name: Rotor-Rear Brake; Brake Rotor; Rotor, Front And Rear Wheel Brake
- Position: Rear
- Replaces: 18019853
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996-1997 Cadillac Seville | SLS, STS | 8 Cyl 4.6 L GAS
View related parts
Cadillac Seville Brake Rotor Part Number: 18017505
Product Specifications
- Other Name: Rotor, Front And Rear Wheel Brake; Rotor
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1995 Cadillac Seville | Base, SLS, STS | 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac Seville Brake Rotor, Front Part Number: 19174912
$49.39 MSRP: $88.20
You Save: $38.81 (44%)
Product Specifications
- Other Name: Rotor Assembly, Front Brake; Disc Brake Hardware Kit; Rotor; Rotor, Front And Rear Wheel Brake
- Position: Front
- Replaces: 18027660
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1985 Cadillac Seville | Base, Elegante | 8 Cyl 4.1 L GAS

Cadillac Seville Brake Disc

Want to cut long-term maintenance and repair costs? Choose OEM Brake Disc. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Cadillac Seville parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Cadillac Seville Brake Disc includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

Cadillac Seville Brake Disc is another important Wolverine automotive spare part for Cadillac Seville that helps in improving efficiency and safety of the cars. Since this kit of Brake Disc is constructed with the exact specifications necessary for particular Seville models manufactured between 1975 and 2004, this kit is a must-have for upgrading the braking system. The Cadillac Seville Brake Disc has the optimal features covering the optimal material that would help drivers to have the optimal stopping power especially under higher demanding conditions. While these are often both a wearing element and a part of the brake drum, the kit often comprises both the brake discs and the brake pads, as well as any related hardware that may consist of clips and shims, which play a significant role in the pad's performance and equal wear. Responsible for translating these themes into the real world is this brake system which interestingly goes through an aggressive, comprehensive strategy that is exigent at ensuring luxury and performance both of which Cadillac Seville is known for. Moreover, the Cadillac Seville Brake Disc is a product designed to work at higher temperatures necessary for normal and extreme driving conditions. The importance of this Brake Disc kit shall be viewed in terms of improving the general performance of the vehicle as well as boosting the reliability hence safety of the vehicle. Thanks to its stability and performance, the Cadillac Seville Brake Disc is revealed to be quite exceptional in the automotive industry, so every Cadillac Seville remains to characterize the unprotected luxury and careful dependability on the road.

Cadillac Seville Brake Disc Parts and Q&A

Rotor
88964102
Q: How to service and repair the Brake Disc using the J41013 and J42450-A kits on Cadillac Seville?
A:
You need both the j41013 disc resurfacing kit (J41013) and the j42450-a Wheel Hub resurfacing kit (J42450-A) to work on your Brake Disc. Start by removing all signs of rust or corrosion from the hub/axle flange using the j42450-a tool before cleaning both surfaces of the Brake Disc and hub/axle flange with the j41013 equipment. Check the surfaces for any unwanted particles that may affect the repair. Install the Brake Disc on the brake lathe as directed by the manufacturer while also making sure clean attachment and adapter components are in place. Fasten vibration dampening equipment first and run the brake lathe while gradually bringing in the grinding tools until they touch only the disc surfaces. Inspect the witness mark on the disc; when it properly extends over three-fourths of both friction surface edges the disc is correctly attached to the brake lathe. If not, re-mount it. Perform the lathe renovation task according to the manufacturer manual and check the disc layers after each trim. The disc has to be replaced if its minimum allowable thickness remains unsupported during refinishing. Apply 120 grit aluminum oxide sandpaper at the indicated speed to finish the disc as recommended by the tool manufacturer. Non-directional finishing tools require 120 grit sandpaper while sanding blocks need 150 grit sandpaper for the process. After applying the finish use denatured alcohol or brake cleaner to wipe clean all brake friction parts. Take the Brake Disc off the lathe and measure its collected llo pattern to keep disc brakes operating at their best while you adjust the results when they exceed the set requirements.
Rotor, Front
19202731
Q: How to replace the front brake disc on Cadillac Seville?
A:
Start Brake Disc replacement by taking off the tire and wheel unit first. Secure the brake caliper always with mechanic's wire whenever you detach it from its mount to keep hydraulic brake hose sealed because improper removal and mounting could break the seal and leak brake fluid. Before continuing you need to take out the brake caliper from its mounting bracket without disconnecting the hydraulic brake flexible hose. Additionally you should remove the Brake Caliper Bracket assembly. Record the disc position on the hub before taking it off. The Brake Disc installation success depends on eliminating all contaminants from both wheel bearing flange and disc contact areas to keep lateral runout and brake vibration under control. Apply the rotor resurfacing kit (J 41013) to wash off rust from both the wheel flange and wheel hub resurfacing kit (J 42450-A) to clean rust from the wheel hub area. Put the Brake Disc on the wheel studs on top of the wheel bearing flange then add the Brake Caliper Bracket assembly and attach the brake caliper to it. Reposition the tire unit at its original location.