How to replace the front brake line on Cadillac Seville?

To install a new brake hose at the front start by using lifts to support the vehicle and then remove the tire and wheel. Make sure you wash dirt away from both brake hose and brake pipe components before adding a rubber cap to shield the exposed brake pipe end to stop fluid loss. Pull away the brake pipe fitting from the brake hose using a flat-blade tool to remove the brake hose retainer before bringing the pipe out of the bracket. Take the brake caliper inlet bolt and brake hose out of their matching places in the caliper. Dispose of the two copper brake hose gaskets since they are generally stuck. Insert a rubber washer to seal the inlet bolt hole before the brake caliper replacement. Take the brake hose away by loosening its bracket bolt from the strut assembly. Install a new copper brake hose gasket before fitting the brake caliper inlet bolt onto its designated hole with the rubber plug removed. Thread the brake caliper inlet fitting bolt with new gaskets to the brake hose when installing it onto the caliper and tightening it to 45 nm (33 ft. Lbs.) while making sure the hose stays straight. Install the brake hose to the bracket and put in the brake hose retainer while removing the rubber protective cap from the brake pipe fitting. Screw the brake pipe fitting onto the brake hose end and tighten it to 15 nm (11 ft. Lbs.). Set up the brake hose bracket and bolt to the strut assembly and torque the bolt to 9 nm (80 inch lbs.). When finished bleed the brake caliper through its bleeder screw then put back the tire and wheel set before placing the vehicle back down.

What tools are required to service and repair the brake line on Cadillac Seville?

A single tool necessary to work on brake hose/line repair is ISO Flaring Kit (J 29803-A). Replace brake pipes with double-walled steel sections since other types can harm brake safety. When replacing brake pipes route and hold them carefully while using the same hardware in its home locations to stop system and damage issues. Start your project by selecting proper sized steel fitting nuts and pipe based on the outside diameter measurement. Cut the new pipe into a square shape and set it at the correct length using a hacksaw. Measure the old pipe for size then add 3.2 mm (0.125 inch) for each ISO flare. Before flaring the pipes, fit the parts first and de-burr both their inner and outer surfaces with the tool. After removing all remaining lubricants from the brake pipe clamp the ISO Flaring Kit (J 29803-A) in a vise for assembly. Place the proper collet and forming mandrel in the kit before putting the mandrel set in its position. After placing the force screw in contact with the mandrel twist it backward by one total revolution. Place the clamping nut over the brake pipe and push the prepared pipe into the collet till 19 mm (0.750 inch) sticks out while keeping the pipe tail on the mandrel face. Screw the clamping nut tightly to keep the pipe from protruding before you wind the forcing screw until it rests firmly on its stop. Avoid excessive fastening to stop flare size overexpansion. Reverse the clamping nut as you remove the collet parts and check the flare diameter to meet the range of 6.92 mm to 7.28 mm (0.272 inch to 0.286 inch). The flare is ready to start using after completion. A tube bender should be used to create new pipe installation following the original path with at least 19 mm (0.75 inch) distance from moving parts, 13 mm (0.50 inch) from vibrating parts, and 7 mm (0.25 inch) space from shielded lines when not directly connected to a component.

OEM Cadillac Seville Brake Line

Brake Hose

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

18 Brake Lines found

View related parts
Cadillac Seville Flex Hose, Front Driver Side Part Number: 19173904
$25.18 MSRP: $44.96
You Save: $19.78 (44%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly, Front Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose
- Position: Front Driver Side
- Replaces: 18032671, 22112075
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1993 Cadillac Seville | Base, STS | 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac Seville Flex Hose, Front Passenger Side Part Number: 19173901
$20.14 MSRP: $35.95
You Save: $15.81 (44%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly, Front Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Front Passenger Side
- Replaces: 18032668, 22112076
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993 Cadillac Seville | Base, STS | 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac Seville Flex Hose, Rear Driver Side Part Number: 18032669
$17.04 MSRP: $30.41
You Save: $13.37 (44%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly, Rear Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose
- Position: Rear Driver Side
- Replaces: 22112077
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992 Cadillac Seville | Base, STS | 8 Cyl 4.9 L GAS
View related parts
Cadillac Seville Flex Hose, Driver Side Part Number: 17982337
$27.14 MSRP: $49.12
You Save: $21.98 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Fitting, Air Conditioner Compressor; Hydraulic Hose; Brake Hose; Brake Line; Front Flex Hose; Hose
- Position: Driver Side
- Replaced by: 18032155
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1989 Cadillac Seville | Base, Elegante, STS | 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS
View related parts
Cadillac Seville Flex Hose, Rear Passenger Side Part Number: 18032670
$16.49 MSRP: $29.45
You Save: $12.96 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly, Rear Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992 Cadillac Seville | Base, STS | 8 Cyl 4.9 L GAS
View related parts
Cadillac Seville Pressure Hose Part Number: 25528398
$30.86
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose, Brake Master Cylinder; Hydraulic Hose; Lower Pressure Hose; Hose, Hydraulic Brake
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1988-1990 Cadillac Seville | Base, STS | 8 Cyl 4.5 L GAS
View related parts
Cadillac Seville Flex Hose, Front Passenger Side Part Number: 19173565
$22.10 MSRP: $39.46
You Save: $17.36 (44%)
ADD TO CART
Product Specifications
- Other Name: Hose Assembly, Front Brake; Hydraulic Hose; Brake Hose; Brake Line; Front Flex Hose; Hose; Hose, Hydraulic Brake
- Position: Front Passenger Side
- Replaces: 17982338, 18032313
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1989 Cadillac Seville | Base, Elegante, STS | 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS
View related parts
Cadillac Seville Flex Hose, Rear Driver Side Part Number: 18032312
$14.34 MSRP: $25.60
You Save: $11.26 (44%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly, Rear Brake; Hydraulic Hose; Brake Hose; Brake Line; Rear Flex Hose; Hose; Hose, Hydraulic Brake
- Position: Rear Driver Side
- Replaces: 19173564
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1991 Cadillac Seville | Base, Elegante, STS | 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac Seville Flex Hose, Rear Part Number: 18032157
$13.14 MSRP: $23.45
You Save: $10.31 (44%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly, Rear Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992 Cadillac Seville | Base, STS | 8 Cyl 4.9 L GAS
View related parts
Cadillac Seville Flex Hose, Front Passenger Side Part Number: 19173614
$20.32 MSRP: $36.29
You Save: $15.97 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly, Front Brake; Hydraulic Hose; Brake Hose; Brake Line; Front Flex Hose; Hose; Hose, Hydraulic Brake
- Position: Front Passenger Side
- Replaces: 22112116, 18032366
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1990-1992 Cadillac Seville | Base, STS | 8 Cyl 4.5 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac Seville Brake Hose, Front Driver Side Part Number: 19173613
$22.88 MSRP: $40.87
You Save: $17.99 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Hose Assembly, Front Brake; Hydraulic Hose; Brake Line; Front Flex Hose; Hose; Hose, Hydraulic Brake
- Position: Front Driver Side
- Replaces: 18032365
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1990-1991 Cadillac Seville | Base, STS | 8 Cyl 4.5 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac Seville Flex Hose, Rear Passenger Side Part Number: 17999968
Product Specifications
- Other Name: Hose Assembly-Rear Brake (Right); Hydraulic Hose; Brake Hose; Brake Line; Rear Flex Hose; Hose, Hydraulic Brake
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993-1997 Cadillac Seville | Base, SLS, STS | 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac Seville Flex Hose, Front Passenger Side Part Number: 19366761
Product Specifications
- Other Name: Hose Assembly, Front Brake; Hydraulic Hose; Brake Hose; Brake Line; Front Flex Hose; Hose, Hydraulic Brake
- Position: Front Passenger Side
- Replaces: 22163448, 17999966, 22163886
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993-2004 Cadillac Seville | Base, SLS, STS | 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac Seville Flex Hose, Front Driver Side Part Number: 19366760
Product Specifications
- Other Name: Hose Assembly, Front Brake; Hydraulic Hose; Brake Hose; Brake Line; Front Flex Hose; Hose, Hydraulic Brake
- Position: Front Driver Side
- Replaces: 22163885, 22163447, 17999817
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1993-2004 Cadillac Seville | Base, SLS, STS | 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS
View related parts
Cadillac Seville Flex Hose, Rear Part Number: 19366759
Product Specifications
- Other Name: Hose Assembly, Rear Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose, Hydraulic Brake
- Position: Rear
- Replaces: 17999820, 22163668, 22113390
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998-2004 Cadillac Seville | SLS, STS | 8 Cyl 4.6 L GAS
View related parts
Cadillac Seville Flex Hose, Driver Side Part Number: 17999819
Product Specifications
- Other Name: Hose, Hydraulic Brake; Hydraulic Hose; Brake Hose; Brake Line
- Position: Driver Side
- Replaced by: 25694864
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1998 Cadillac Seville | SLS, STS | 8 Cyl 4.6 L GAS
View related parts
Cadillac Seville Flex Hose, Rear Part Number: 1261559
Product Specifications
- Other Name: Hose, Rear Brake; Hydraulic Hose; Brake Hose; Brake Line; Hose
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1985 Cadillac Seville | Base, Elegante | 8 Cyl 4.1 L GAS, 8 Cyl 5.7 L DIESEL
View related parts
Cadillac Seville Flex Hose, Rear Passenger Side Part Number: 19173566
$11.55 MSRP: $20.62
You Save: $9.07 (44%)
Product Specifications
- Other Name: Hose Assembly, Rear Brake; Hydraulic Hose; Brake Hose; Brake Line; Rear Flex Hose; Hose; Hose, Hydraulic Brake
- Position: Rear Passenger Side
- Replaces: 18032314, 17985580
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1986-1991 Cadillac Seville | Base, Elegante, STS | 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS, 8 Cyl 4.9 L GAS

Cadillac Seville Brake Line

Want to cut long-term maintenance and repair costs? Choose OEM Brake Line. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Cadillac Seville parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Cadillac Seville Brake Line includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

Cadillac Seville Brake Line Parts and Q&A

Flex Hose, Front Passenger Side
19366761
Q: How to replace the front brake line on Cadillac Seville?
A:
To install a new brake hose at the front start by using lifts to support the vehicle and then remove the tire and wheel. Make sure you wash dirt away from both brake hose and brake pipe components before adding a rubber cap to shield the exposed brake pipe end to stop fluid loss. Pull away the brake pipe fitting from the brake hose using a flat-blade tool to remove the brake hose retainer before bringing the pipe out of the bracket. Take the brake caliper inlet bolt and brake hose out of their matching places in the caliper. Dispose of the two copper brake hose gaskets since they are generally stuck. Insert a rubber washer to seal the inlet bolt hole before the brake caliper replacement. Take the brake hose away by loosening its bracket bolt from the strut assembly. Install a new copper brake hose gasket before fitting the brake caliper inlet bolt onto its designated hole with the rubber plug removed. Thread the brake caliper inlet fitting bolt with new gaskets to the brake hose when installing it onto the caliper and tightening it to 45 nm (33 ft. Lbs.) while making sure the hose stays straight. Install the brake hose to the bracket and put in the brake hose retainer while removing the rubber protective cap from the brake pipe fitting. Screw the brake pipe fitting onto the brake hose end and tighten it to 15 nm (11 ft. Lbs.). Set up the brake hose bracket and bolt to the strut assembly and torque the bolt to 9 nm (80 inch lbs.). When finished bleed the brake caliper through its bleeder screw then put back the tire and wheel set before placing the vehicle back down.
Flex Hose, Front Driver Side
19366760
Q: What tools are required to service and repair the brake line on Cadillac Seville?
A:
A single tool necessary to work on brake hose/line repair is ISO Flaring Kit (J 29803-A). Replace brake pipes with double-walled steel sections since other types can harm brake safety. When replacing brake pipes route and hold them carefully while using the same hardware in its home locations to stop system and damage issues. Start your project by selecting proper sized steel fitting nuts and pipe based on the outside diameter measurement. Cut the new pipe into a square shape and set it at the correct length using a hacksaw. Measure the old pipe for size then add 3.2 mm (0.125 inch) for each ISO flare. Before flaring the pipes, fit the parts first and de-burr both their inner and outer surfaces with the tool. After removing all remaining lubricants from the brake pipe clamp the ISO Flaring Kit (J 29803-A) in a vise for assembly. Place the proper collet and forming mandrel in the kit before putting the mandrel set in its position. After placing the force screw in contact with the mandrel twist it backward by one total revolution. Place the clamping nut over the brake pipe and push the prepared pipe into the collet till 19 mm (0.750 inch) sticks out while keeping the pipe tail on the mandrel face. Screw the clamping nut tightly to keep the pipe from protruding before you wind the forcing screw until it rests firmly on its stop. Avoid excessive fastening to stop flare size overexpansion. Reverse the clamping nut as you remove the collet parts and check the flare diameter to meet the range of 6.92 mm to 7.28 mm (0.272 inch to 0.286 inch). The flare is ready to start using after completion. A tube bender should be used to create new pipe installation following the original path with at least 19 mm (0.75 inch) distance from moving parts, 13 mm (0.50 inch) from vibrating parts, and 7 mm (0.25 inch) space from shielded lines when not directly connected to a component.