How to service the front wheel bearing and hub on Cadillac Escalade?

Before servicing the front Wheel Bearing and hub, you need to raise the vehicle and hold it up using suitable safety stands. After taking off the wheel and tire, use a wire to hold the brake caliper and avoid harming the Brake Line. Cover the inside and outside of the c/v joint boots with shop towels to prevent them from being damaged during the process. After that, remove the brake caliper, drive axle nut, washer and brake rotor. When the tie rod nut is removed, disconnect the Tie Rod End from the knuckle and place the hub and bearing assembly on the side of the hub bolt so it does not get dirty. Place a puller on the hub and bearing assembly to release it and then use a socket or ratchet to unscrew the bolts that hold down the halfshaft and the splash shield before you remove the shield. Place a jack stand beneath the lower Control Arm, remove the upper and lower Ball Joint nuts and detach the ball joints from the knuckle with j 36607 before you take out the knuckle and seal. While installing, insert the seal into the j 36605 first, then connect the ball joints to the knuckle, install the nuts on the studs and tighten the lower one to 128 nm (94 ft. Lbs.) and the upper one to 100 nm (74 ft. Lbs.) without applying too much torque. Put on the new cotter pins, fit and bolt in the splash shield and tighten them to 26 nm (19 ft. Lbs.). Treat the seals inside the steering knuckle with grease, slip on the half shaft, place the hub and bearings assembly, arrange the holes for evenness and tighten the bolts to 180 nm (133 ft. Lbs.). Attach the Tie Rod End to the knuckle, fasten it using the nut and tighten it to 48 nm (35 ft. Lbs.). Then, set the washer, followed by the drive axle nut that you should tighten to 225 nm (165 ft. Lbs.). The last step is to add the rotor and Brake Calipers, attach the tire and wheel setup, take down the jack stand, lower the vehicle and make sure the trim height is correct and alter it if needed.

How to replace the rear wheel bearing on Cadillac Escalade?

Raising the vehicle lets you take off the tire and wheel to replace the rear Wheel Hub bearing. The next step is to take off the Steering Knuckle tie rod and uninstall the brake rotor. Remove the dust cover from the wheel drive shaft axle nut before taking off the wheel drive shaft retaining pin and wheel drive shaft nut. Insert the axle remover tool j 45859 between wheel drive shaft and Wheel Hub and bearing to detach them from each other before taking out the Wheel Hub and bearing assembly from the vehicle. Install the Wheel Hub by fitting it into the vehicle space and tightening its holding bolts to 140 n.m (103 lb ft). When installing the wheel drive shaft nut tighten it carefully to 250 n.m (184 lb ft). Secure the wheel drive shaft nut by putting its retainer and cotter pin in place and then install the dust cap. Bring the vehicle back down from its lifted position while rehiding the brake rotor followed by fitting the outer tie rod to the Steering Knuckle then placing back the tire and wheel.

OEM Cadillac Escalade Wheel Bearing

Hub Bearing

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

20 Wheel Bearings found

View related parts
Cadillac Escalade Wheel Bearing Part Number: 457049
$24.87 MSRP: $45.03
You Save: $20.16 (45%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Bearing, Front Wheel Outer; Axle Bearing; Wheel Bearings; Front Wheel Bearing; Front Bearing; Outer Wheel Bearing; Outer Bearing; Bearing
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1999-2000 Cadillac Escalade | Base | 8 Cyl 5.7 L GAS
View related parts
Cadillac Escalade Wheel Bearing, Front Part Number: 457052
$38.44 MSRP: $66.52
You Save: $28.08 (43%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Bearing, Front Wheel Inner; Axle Bearing; Wheel Bearings; Front Inner Bearing; Bearing Assembly, Transmission Main Shaft; Gear Bearings; Front Outer Bearing.
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1999-2000 Cadillac Escalade | Base | 8 Cyl 5.7 L GAS
View related parts
Cadillac Escalade Hub, Rear Part Number: 15725055
$341.37 MSRP: $527.97
You Save: $186.60 (36%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Rear Wheel; Hub, Rear Wheel
- Position: Rear
- Replaces: 00365897, 365897
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1999-2000 Cadillac Escalade | Base | 8 Cyl 5.7 L GAS
View related parts
Cadillac Escalade Wheel Bearing Part Number: 9428908
$72.07 MSRP: $98.04
You Save: $25.97 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Rear Wheel Outer; Axle Bearings, Shaft Bearings, Grease Cap, Outer Bearing, Bearing Assembly, Front Wheel Outer, Rear Wheel.
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1999-2000 Cadillac Escalade | Base | 8 Cyl 5.7 L GAS
View related parts
Cadillac Escalade Wheel Bearing Part Number: 9439561
$72.53 MSRP: $131.28
You Save: $58.75 (45%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rear Wheel Bearing; Axle Bearing; Axle Bearings; Shaft Bearings; Outer Bearing; Bearing; Bearing, Rear Axle Shaft; Bearing, Rear Wheel
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2006, 1999-2000 Cadillac Escalade | Base | 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L GAS
View related parts
Cadillac Escalade Wheel Bearing Part Number: 9436881
$57.71 MSRP: $145.36
You Save: $87.65 (61%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Differential; Differential Pinion Bearing; Differential Bearing; Axle Bearings; Shaft; Inner; Side; Differential Gear; Front Wheel; Rear Wheel; Nut.
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2006, 1999-2000 Cadillac Escalade | Base | 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L GAS
View related parts
Cadillac Escalade Output Shaft Bearing, Front Part Number: 26066885
$30.92 MSRP: $58.06
You Save: $27.14 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Front Axle; Differential Pinion Bearing; Wheel Bearing; Axle Bearing; Inner Pinion Bearing; Bearing, Front Axle And Axle Center
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2020, 2002-2005 Cadillac Escalade | Base, Hybrid, Hybrid Platinum, Luxury, Platinum, Premium, Premium Luxury | 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Cadillac Escalade Wheel Bearing, Rear Part Number: 12479031
$49.62 MSRP: $96.32
You Save: $46.70 (49%)
ADD TO CART
Product Specifications
- Other Name: Bearing, Rear Axle Shaft; Wheel Bearing Kit; Axle Bearing; Axle Bearings; Shaft Bearings; Outer Bearing; Bearing; Bearing, Rear Wheel
- Position: Rear
- Replaces: 09442126, 9442126
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2020, 1999-2000 Cadillac Escalade | Base, Hybrid, Hybrid Platinum, Luxury, Platinum, Premium, Premium Luxury | 8 Cyl 5.3 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Cadillac Escalade Wheel Bearings, Front Inner Part Number: 15595151
$75.48 MSRP: $141.74
You Save: $66.26 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Front Wheel Inner; Wheel Bearing; Axle Bearing; Inner Bearing
- Position: Front Inner
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1999-2000 Cadillac Escalade | Base | 8 Cyl 5.7 L GAS
View related parts
Cadillac Escalade Wheel Bearings Part Number: 457043
$59.61 MSRP: $98.54
You Save: $38.93 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing, Front Wheel Outer; Wheel Bearing; Axle Bearing; Front Wheel Bearing; Outer Bearing
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1999-2000 Cadillac Escalade | Base | 8 Cyl 5.7 L GAS
View related parts
Cadillac Escalade Wheel Bearing, Front Part Number: 457232
$29.38 MSRP: $50.52
You Save: $21.14 (42%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Front Wheel Brace; Wheel Bearings; Front Outer & Inner Bearings; Differential Side Gear Bearing.
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1999-2000 Cadillac Escalade | Base | 8 Cyl 5.7 L GAS
View related parts
Cadillac Escalade Hub Assembly Part Number: 13536121
$130.01 MSRP: $235.32
You Save: $105.31 (45%)
ADD TO CART
Product Specifications
- Other Name: Hub, Rear Wheel (W/Bearing); Wheel Hub; Rear Hub & Bearing; Hub, Rear Wheel
- Replaced by: 13549865
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2023 Cadillac Escalade | Luxury, Premium Luxury, Premium Luxury Platinum, Sport, Sport Platinum, V | 6 Cyl 3.0 L DIESEL, 8 Cyl 6.2 L GAS
View related parts
Cadillac Escalade Front Hub Part Number: 84856653
$241.51 MSRP: $472.84
You Save: $231.33 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Front Wheel (W/ Bearing & Wheel Speed Sensor); Wheel Hub Repair Kit; Wheel Bearing; Axle Bearing; Wheel Hub; Hub & Bearing; Hub, Front Wheel
- Position: Front
- Replaces: 10393170, 20883242, 84356642, 25819677, 22841380
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2007-2014 Cadillac Escalade | Base, Hybrid, Hybrid Platinum, Luxury, Platinum, Premium | 8 Cyl 6.0 L FULL HYBRID EV-FLEX (FHEV), 8 Cyl 6.0 L FULL HYBRID EV-GAS (FHEV), 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Cadillac Escalade Axle Bearings, Front Part Number: 23243752
$10.11 MSRP: $18.98
You Save: $8.87 (47%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing Assembly-Front Differential; Wheel Bearing; Axle Bearing; Output Shaft Bearing; Bearing, Front Axle
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2021-2023 Cadillac Escalade | Luxury, Premium Luxury, Premium Luxury Platinum, Sport, Sport Platinum, V | 6 Cyl 3.0 L DIESEL, 8 Cyl 6.2 L GAS
View related parts
Cadillac Escalade Hub Assembly Part Number: 84869190
$183.91 MSRP: $356.94
You Save: $173.03 (49%)
ADD TO CART
Product Specifications
- Other Name: Hub Assembly-Front Wheel (W/ Bearing & Wheel Speed Sensor); Wheel Hub Repair Kit; Wheel Bearing; Axle Bearing; Wheel Hub; Front Hub & Bearing; Front Hub; Hub & Bearing; Hub, Front Wheel; Hub, Rear Wheel
- Position: Front
- Replaced by: 85689422
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2015-2020 Cadillac Escalade | Base, Luxury, Platinum, Premium, Premium Luxury | 8 Cyl 6.2 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Cadillac Escalade Front Hub Part Number: 15233113
Product Specifications
- Other Name: Hub, Front Wheel (W/Wheel Speed Sensor); Wheel Bearing & Hub Assembly; Repair Kit; Axle Bearing.; Hub & Bearing; Hub
- Position: Front
- Replaces: 15112382, 15134584, 15740291
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2002-2006 Cadillac Escalade | Base | 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
View related parts
Cadillac Escalade Hub & Bearing, Front Driver Side Part Number: 15997071
Product Specifications
- Other Name: Hub, Front Wheel; Wheel Bearing & Hub Assembly; Repair Kit; Axle Bearing.
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1999-2000 Cadillac Escalade | Base | 8 Cyl 5.7 L GAS
View related parts
Cadillac Escalade Outer Bearing Part Number: 9412405
Product Specifications
- Other Name: Bearing, Rear Wheel Outer; Wheel Bearing; Axle Bearing; Bearing, Rear Wheel
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1999-2000 Cadillac Escalade | Base | 8 Cyl 5.7 L GAS
View related parts
Cadillac Escalade Inner Bearing Part Number: 9412426
Product Specifications
- Other Name: Bearing; Wheel Bearing; Axle Bearing; Bearing, Rear Wheel
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1999-2000 Cadillac Escalade | Base | 8 Cyl 5.7 L GAS
View related parts
Cadillac Escalade Hub & Bearing, Front Passenger Side Part Number: 15997072
Product Specifications
- Other Name: Hub, Front Wheel; Wheel Bearing & Hub Assembly; Repair Kit; Axle Bearing.
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1999-2000 Cadillac Escalade | Base | 8 Cyl 5.7 L GAS

Cadillac Escalade Wheel Bearing

Want to cut long-term maintenance and repair costs? Choose OEM Wheel Bearing. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Cadillac Escalade parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Cadillac Escalade Wheel Bearing includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

The Wheel Bearing in Cadillac Escalade vehicles is used to let the wheel rotate without experiencing drag while at the same time providing safety to the driver. In the majority of current designs, the hub and bearing assembly is integrated or unitized and usually includes the ABS sensor and is removed as a complete assembly. There are some front-wheel-drive Escalade models where the steering knuckle may have to be pulled out for service, whereas nondriven axle hubs incorporate replaceable tapered roller bearings. Inadequate or damaged Wheel Bearings may cause noise, and vibration and at worst, wheel loss hence requiring regular check up. To Cadillac Escalade owners it is recommended that, Wheel Bearings' condition should be checked for roughness and play in order to sustain the worthy performance of the vehicle as well as safety. However, if replacement is to be done then proper fitment and alignment of the bearings is important to perform its function effectively.

Cadillac Escalade Wheel Bearing Parts and Q&A

Wheel Bearing
457049
Q: How to service the front wheel bearing and hub on Cadillac Escalade?
A:
Before servicing the front Wheel Bearing and hub, you need to raise the vehicle and hold it up using suitable safety stands. After taking off the wheel and tire, use a wire to hold the brake caliper and avoid harming the Brake Line. Cover the inside and outside of the c/v joint boots with shop towels to prevent them from being damaged during the process. After that, remove the brake caliper, drive axle nut, washer and brake rotor. When the tie rod nut is removed, disconnect the Tie Rod End from the knuckle and place the hub and bearing assembly on the side of the hub bolt so it does not get dirty. Place a puller on the hub and bearing assembly to release it and then use a socket or ratchet to unscrew the bolts that hold down the halfshaft and the splash shield before you remove the shield. Place a jack stand beneath the lower Control Arm, remove the upper and lower Ball Joint nuts and detach the ball joints from the knuckle with j 36607 before you take out the knuckle and seal. While installing, insert the seal into the j 36605 first, then connect the ball joints to the knuckle, install the nuts on the studs and tighten the lower one to 128 nm (94 ft. Lbs.) and the upper one to 100 nm (74 ft. Lbs.) without applying too much torque. Put on the new cotter pins, fit and bolt in the splash shield and tighten them to 26 nm (19 ft. Lbs.). Treat the seals inside the steering knuckle with grease, slip on the half shaft, place the hub and bearings assembly, arrange the holes for evenness and tighten the bolts to 180 nm (133 ft. Lbs.). Attach the Tie Rod End to the knuckle, fasten it using the nut and tighten it to 48 nm (35 ft. Lbs.). Then, set the washer, followed by the drive axle nut that you should tighten to 225 nm (165 ft. Lbs.). The last step is to add the rotor and Brake Calipers, attach the tire and wheel setup, take down the jack stand, lower the vehicle and make sure the trim height is correct and alter it if needed.
Wheel Bearing
9439561
Q: How to replace the rear wheel bearing on Cadillac Escalade?
A:
Raising the vehicle lets you take off the tire and wheel to replace the rear Wheel Hub bearing. The next step is to take off the Steering Knuckle tie rod and uninstall the brake rotor. Remove the dust cover from the wheel drive shaft axle nut before taking off the wheel drive shaft retaining pin and wheel drive shaft nut. Insert the axle remover tool j 45859 between wheel drive shaft and Wheel Hub and bearing to detach them from each other before taking out the Wheel Hub and bearing assembly from the vehicle. Install the Wheel Hub by fitting it into the vehicle space and tightening its holding bolts to 140 n.m (103 lb ft). When installing the wheel drive shaft nut tighten it carefully to 250 n.m (184 lb ft). Secure the wheel drive shaft nut by putting its retainer and cotter pin in place and then install the dust cap. Bring the vehicle back down from its lifted position while rehiding the brake rotor followed by fitting the outer tie rod to the Steering Knuckle then placing back the tire and wheel.