How to Properly Service and Replace the Brake Proportioning Valve on Cadillac Eldorado?

Start by uncovering both left and right proportioning valves under the vehicle. Before beginning protect the brake pipe fitting from air and fluid exposure through a rubber cap. Take out both left and right proportioning valves from their location on the brake line. The right fasteners need to go into their proper positions during valve installation. Also use replacement fasteners with the numbers that apply to the specific system. Apply fasteners without paints, lubricants, or corrosion protectants because these substances reduce the torque and force of the joint connection and may harm the fasteners. Use the defined tightening method to keep components safe. Install left/and right proportioning valves to brake pipe fitments and fasten them with 15 Nm torque. The last step is to drain all hydraulic brake fluid from the system.

What steps should be followed for replacing the Brake Proportioning Valve on Cadillac Escalade?

Before replacing it, take note of the code marked on the old valve for the right replacement. Start by taking out the combination valve's electrical connector, proceed with removing the front brake lines and then continue with the rear brake lines. In the next step, take out the three alien bolts (11) securing the combination valve (12) to the bpmv and get rid of the combination valve (12) and the two transfer tubes (13). Be certain that transfer lines (13) are new when you replace the combination valve and that the replacement code punched into the part is the same as the one in the old combination valve. Attach the two transfer tubes (13) to the combination valve until they are seated, after which you should put the combination valve (12) onto the bpmv. Install the three combination valve bolts (11) and tighten them at first only to 8 nm (6 ft. Lbs.), then to 16 nm (12 ft. Lbs.). Cover the front and rear brake pipes with the combination valve, tighten each of the brake pipe fittings to 24 nm (18 ft. Lbs.) and then connect the combination valve to the electrical connector. A final step is to ensure the combination valve metering rod is pushed in as you start bleeding and then proceed with the brake bleeding.

OEM Cadillac Brake Proportioning Valve

Proportioning Valve

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

23 Brake Proportioning Valves found

View related parts
Cadillac Pressure Metering Valve Part Number: 19244448
$49.91 MSRP: $85.31
You Save: $35.40 (42%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Valve, Brake Master Cylinder Proportioning; Brake Proportioning Valve
- Replaces: 25630070, 25626929
Fits the following Cadillac Models:
- 60 Special | 1993 | Base | 8 Cyl 4.9 L GAS
- DeVille | 1997-2002, 1992-1993 | Base, Concours, d'Elegance, DHS, DTS, Touring | 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS
- Eldorado | 1997-2002 | Base, ESC, ETC | 8 Cyl 4.6 L GAS
- Fleetwood | 1992 | 60 Special, Base, d'Elegance | 8 Cyl 4.9 L GAS
- Seville | 1997-1999 | SLS, STS | 8 Cyl 4.6 L GAS
View More
View related parts
Cadillac Pressure Metering Valve Part Number: 12548265
Product Specifications
- Other Name: Valve Kit, Brake Combination; Brake Proportioning Valve; Valve; Valve Kit, Hydraulic Brake Combination/Monitoring Valve; Valve, Hydraulic Brake Combination/Monitoring Valve
Fits the following Cadillac Models:
- Escalade | 1999-2000 | Base | 8 Cyl 5.7 L GAS
View related parts
Cadillac Pressure Valve Part Number: 25731523
Product Specifications
- Other Name: Valve, Electronic Brake Control; ABS Pump And Motor Assembly; ABS Control Module; Modulator Valve; ABS Pump Assembly; Pressure Modulator Valve; ABS Regulator; Modulator
- Replaces: 25641265
Fits the following Cadillac Models:
- DeVille | 1997-1999 | Base, Concours, d'Elegance | 8 Cyl 4.6 L GAS
- Eldorado | 1997-2002 | Base, ESC, ETC | 8 Cyl 4.6 L GAS
- Seville | 1997 | SLS, STS | 8 Cyl 4.6 L GAS
View More
View related parts
Cadillac Pressure Valve Part Number: 88983913
Product Specifications
- Other Name: Valve, Brake Pressure Mode; ABS Control Module; Modulator Valve; Valve, Electronic Brake Control
- Replaces: 88982364, 88948552
Fits the following Cadillac Models:
- Escalade | 2002 | Base | 8 Cyl 5.3 L GAS, 8 Cyl 6.0 L GAS
- Escalade EXT | 2002 | Base | 8 Cyl 6.0 L GAS
View related parts
Cadillac Pressure Metering Valve Part Number: 3523171
Product Specifications
- Other Name: Valve Assembly-Brake Combination; Brake Proportioning Valve; Valve, Hydraulic Brake Combination/Monitoring Valve
Fits the following Cadillac Models:
- Fleetwood | 1993 | Base, Brougham | 8 Cyl 5.7 L GAS
View related parts
Cadillac Pressure Valve Part Number: 19416841
Product Specifications
- Other Name: Valve Assembly, Brake Pressure Mode; ABS Pump And Motor Assembly; Modulator Valve; ABS Pump Assembly; Valve; Valve, Electronic Brake Control
- Replaces: 25720864, 25698056
Fits the following Cadillac Models:
- DeVille | 2001 | Base, DHS, DTS | 8 Cyl 4.6 L GAS
View related parts
Cadillac Modulator Valve Part Number: 19416854
Product Specifications
- Other Name: Valve Assembly, Brake Pressure Mode; Modulator; Valve, Electronic Brake Control
- Replaces: 25966978
Fits the following Cadillac Models:
- XLR | 2009 | Platinum, V | 8 Cyl 4.4 L GAS, 8 Cyl 4.6 L GAS
View related parts
Cadillac Modulator Valve Part Number: 3545142
Product Specifications
- Other Name: Valve Assembly-Brake Pressure Mod; ABS Control Module; ABS Regulator; Control Module Assembly; Modulator; Valve, Electronic Brake Control
Fits the following Cadillac Models:
- Allante | 1993 | Base, Indianapolis 500 Pace Car, Value Leader | 8 Cyl 4.6 L GAS
- DeVille | 1994 | Concours | 8 Cyl 4.6 L GAS
- Eldorado | 1993-1994 | Base, Sport, Touring | 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS
- Seville | 1993-1994 | Base, SLS, STS | 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS
View More
View related parts
Cadillac Pressure Valve Part Number: 19416835
Product Specifications
- Other Name: Valve Assembly, Brake Pressure Mode; ABS Pump And Motor Assembly; Modulator Valve; ABS Pump Assembly; Valve; Modulator; Valve, Electronic Brake Control
- Replaces: 25720865, 25698057
Fits the following Cadillac Models:
- DeVille | 2000-2005 | Base, DHS, DTS, Protection Series | 8 Cyl 4.6 L GAS
- Seville | 2000-2004 | SLS, STS | 8 Cyl 4.6 L GAS
View related parts
Cadillac Valve Block Part Number: 25533639
Product Specifications
- Other Name: Valve, Brake Master Cylinder Proportioning; Brake Proportioning Valve; Pressure Metering Valve; Modulator; Valve, Brake Master Cylinder Reservoir
Fits the following Cadillac Models:
- Brougham | 1989-1990 | Base, d'Elegance | 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS
- DeVille | 1989-1990 | Base | 8 Cyl 4.5 L GAS
- Fleetwood | 1989-1990 | 60 Special, Base, d'Elegance | 8 Cyl 4.5 L GAS
View More
View related parts
Cadillac Modulator Valve Part Number: 25731524
Product Specifications
- Other Name: Valve, Electronic Brake Control; ABS Control Module; Modulator
- Replaces: 25676944
Fits the following Cadillac Models:
- DeVille | 1998-1999 | Base, Concours, d'Elegance | 8 Cyl 4.6 L GAS
- Eldorado | 1998-2002 | ESC, ETC | 8 Cyl 4.6 L GAS
- Seville | 1998-1999 | SLS, STS | 8 Cyl 4.6 L GAS
View More
View related parts
Cadillac Modulator Valve Part Number: 3542471
Product Specifications
- Other Name: Valve Assembly-Brake Pressure Mod; Brake Proportioning Valve; ABS Control Module; ABS Regulator; Valve; Modulator; Valve, Electronic Brake Control
Fits the following Cadillac Models:
- DeVille | 1994 | Base, Concours | 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS
- Eldorado | 1992-1993 | Base, Sport, Touring | 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS
- Seville | 1992-1994 | Base, SLS, STS | 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS
View More
View related parts
Cadillac Modulator Valve Part Number: 25731990
Product Specifications
- Other Name: Valve, Electronic Brake Control; ABS Control Module; ABS Regulator; Modulator
- Replaces: 03548961, 3548961
Fits the following Cadillac Models:
- DeVille | 1995-1997 | Base, Concours, d'Elegance | 8 Cyl 4.6 L GAS, 8 Cyl 4.9 L GAS
- Eldorado | 1995-1997 | Base, ETC | 8 Cyl 4.6 L GAS
- Seville | 1995-1997 | SLS, STS | 8 Cyl 4.6 L GAS
View More
View related parts
Cadillac Pressure Metering Valve Part Number: 3634701
Product Specifications
- Other Name: Valve; Brake Proportioning Valve; Valve, Brake Master Cylinder Proportioning
Fits the following Cadillac Models:
- Allante | 1987-1992 | Base, Value Leader | 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS
View related parts
Cadillac Pressure Valve Part Number: 25525844
Product Specifications
- Other Name: Valve, Electronic Brake Control; Valve, Brake Master Cylinder Proportioning
Fits the following Cadillac Models:
- Eldorado | 1988-1990 | Base, Biarritz, Touring | 8 Cyl 4.5 L GAS
View related parts
Cadillac Pressure Metering Valve Part Number: 10250986
Product Specifications
- Other Name: Valve Assembly-Brake Combination; Brake Proportioning Valve; Valve, Hydraulic Brake Combination/Monitoring Valve
Fits the following Cadillac Models:
- Fleetwood | 1994-1996 | Base, Brougham | 8 Cyl 5.7 L GAS
View related parts
Cadillac Pressure Metering Valve Part Number: 25509419
Product Specifications
- Other Name: Valve, Brake Combination; Brake Proportioning Valve; Valve, Hydraulic Brake Combination/Monitoring Valve
Fits the following Cadillac Models:
- Fleetwood | 1984 | Formal | 8 Cyl 6.0 L GAS
View related parts
Cadillac Fuel Filter Part Number: 1257200
Product Specifications
- Other Name: Valve, Brake Combsw Assembly; Brake Proportioning Valve; Pressure Metering Valve; Valve, Hydraulic Brake Combination/Monitoring Valve
Fits the following Cadillac Models:
- Fleetwood | 1993 | Base, Brougham | 8 Cyl 5.7 L GAS
View related parts
Cadillac Pressure Metering Valve Part Number: 10223533
Product Specifications
- Other Name: Valve Assembly-Brake Combination; Brake Proportioning Valve; Valve, Hydraulic Brake Combination/Monitoring Valve
Fits the following Cadillac Models:
- Fleetwood | 1994-1996 | Base, Brougham | 8 Cyl 5.7 L GAS
View related parts
Cadillac Valve Block Part Number: 25530880
Product Specifications
- Other Name: Valve-Brake; Brake Proportioning Valve; Pressure Metering Valve; Valve, Brake Master Cylinder Reservoir
Fits the following Cadillac Models:
- Brougham | 1987-1988 | Base, d'Elegance | 8 Cyl 5.0 L GAS
- DeVille | 1986-1988 | Base, d'Elegance, Touring | 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS
- Fleetwood | 1986-1988 | 60 Special, 75, 75 Formal, Base, Brougham, Brougham d'Elegance, d'Elegance | 8 Cyl 4.1 L GAS, 8 Cyl 4.5 L GAS, 8 Cyl 5.0 L GAS
View More

| Page 1 of 2 |Next >

1-20 of 23 Results

Cadillac Brake Proportioning Valve

Choose OEM Brake Proportioning Valve, you're making the optimal decision for superior quality and perfect performance. You can feel confident because each component goes through stringent quality checks. Every part is carefully built to comply with Cadillac's factory specifications. You'll enjoy a smooth, worry-free installation that fits just right. At ChevyPartsDeal.com, you'll find it easy to get top-quality OEM Cadillac Brake Proportioning Valve. You can shop at highly competitive prices and protect your budget. All our genuine Cadillac parts include a dependable manufacturer's warranty. You'll also appreciate our straightforward return policy and swift delivery services for extra convenience.

Cadillac Brake Proportioning Valve balances the front and rear pressure of the brakes in order to ensure that the tires still have grip. Cadillac is motoring history that is tall with its bold styling and century of know-how. Cadillac clients enter rooms that are lined with luxurious fabrics, sharp screens, and user-friendly features that do not complicate long journeys. Cadillac continues its all-electric development as seen in the hand-built Celestiq, and luxury can grow without losing character. The marque prides itself on comfort rather than gimmicks, thus it is more oriented at sound cabins, balanced ride, and swift steering reaction. Owners like the fact that the brand is a blend of heritage symbols and glass roofs and battery platforms that look into the next century. All the models convey confidence on the road courtesy of aggressive grilles, sharp lighting, and body lines that appear molded and not etched. Brake Proportioning Valve is installed between the master cylinder and rear lines, and this valve registers the hydraulic pressure in real time, thus determining the proportion of force to be applied to each axis. Brake Proportioning Valve helps to delay the lock-up of the rear drums before they fill up, which keeps the steering reactive during panic stops. Brake Proportioning Valve also elevates the total stopping effectiveness since harmonized pressure implies that the front discs are biting hard without the back wheels skidding. The device includes a calibrated piston and spring, which react to threshold forces of the fluid and transform the excessive rear line force into harmless bypass flow.

Cadillac Brake Proportioning Valve Parts and Q&A

Pressure Metering Valve
19244448
Q: How to Properly Service and Replace the Brake Proportioning Valve on Cadillac Eldorado?
A:
Start by uncovering both left and right proportioning valves under the vehicle. Before beginning protect the brake pipe fitting from air and fluid exposure through a rubber cap. Take out both left and right proportioning valves from their location on the brake line. The right fasteners need to go into their proper positions during valve installation. Also use replacement fasteners with the numbers that apply to the specific system. Apply fasteners without paints, lubricants, or corrosion protectants because these substances reduce the torque and force of the joint connection and may harm the fasteners. Use the defined tightening method to keep components safe. Install left/and right proportioning valves to brake pipe fitments and fasten them with 15 Nm torque. The last step is to drain all hydraulic brake fluid from the system.
Pressure Metering Valve
12548265
Q: What steps should be followed for replacing the Brake Proportioning Valve on Cadillac Escalade?
A:
Before replacing it, take note of the code marked on the old valve for the right replacement. Start by taking out the combination valve's electrical connector, proceed with removing the front brake lines and then continue with the rear brake lines. In the next step, take out the three alien bolts (11) securing the combination valve (12) to the bpmv and get rid of the combination valve (12) and the two transfer tubes (13). Be certain that transfer lines (13) are new when you replace the combination valve and that the replacement code punched into the part is the same as the one in the old combination valve. Attach the two transfer tubes (13) to the combination valve until they are seated, after which you should put the combination valve (12) onto the bpmv. Install the three combination valve bolts (11) and tighten them at first only to 8 nm (6 ft. Lbs.), then to 16 nm (12 ft. Lbs.). Cover the front and rear brake pipes with the combination valve, tighten each of the brake pipe fittings to 24 nm (18 ft. Lbs.) and then connect the combination valve to the electrical connector. A final step is to ensure the combination valve metering rod is pushed in as you start bleeding and then proceed with the brake bleeding.