How to service and repair the front motor and transmission mount on Buick Park Avenue?

Begin transmission mount servicing and repair by removing the front transmission mount bracket followed by vehicle elevation and support. Start by removing the nut that holds the front transmission mount to the frame followed by vehicle lowering and front transmission mount extraction. You need to pass the front transmission mount's long stud through the frame hole using a hoisted vehicle. When your work is complete, reinstall the front transmission mount at the frame using a 70 Nm (52 ft. lbs.) torque setting on the nut. Repositioning the front transmission mount bracket should be the final step after lowering the vehicle.

How to replace the LH Motor and Transmission Mount on Buick Park Avenue?

In order to change the left transmission mount, lift and support the vehicle together with the removal of the left front tire, wheel and left front fascia extension. Set an assembly stand under the transaxle in order to towel the powertrain and take off the mount stud nut from the mount stud to detach the mount from the mount bracket. Then take off the nut, bolt and nuts from the vehicle, slowly bring down the transaxle stand and remove it. Lower and remove the retaining screws for the frame rail bolt before lifting the vehicle again. Push up on the frame rail bolts to clear the mount as the top of the mount tilts away from the vehicle and then remove the mount. For installation, put the mount stud into the transaxle mount bracket, lift the frame rail support bolts out of the mount while making rotations to position, and make sure to align and insert the loose frame rail support bolts into the mount. Lower the vehicle and install the frame rail bolt retaining screws, tightened to 4 Nm (35 inch lbs.). Lift up the vehicle again; fix the mount bolt and turn it in a counterclockwise direction to fix the anti-rotation tab behind the mount bracket, and the mount nuts, tightening these to 70 Nm (52 ft. lbs.). Position the powertrain on the transaxle stand and load the mount, then apply the mount stud nut tightly to 80 Nm (59 ft. lbs.). Remove the transaxle stand and reintroduce the left front fascia extension, the left front tire and wheel, and finally lower the vehicle.

OEM Buick Park Avenue Motor And Transmission Mount

Motor and Trans Mount

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

23 Motor And Transmission Mounts found

View related parts
Buick Park Avenue Transmission Mount, White, Rear Part Number: 25723646
$71.20 MSRP: $113.04
You Save: $41.84 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Mount Assembly-Transmission Rear *White; Engine Mount Bracket; Transfer Case Mount; Motor Mount; Rear Mount; Mount, Transmission Mounting
- Position: Rear
- Replaces: 25693540, 25705524
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1999-2005 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Transmission Mount Part Number: 25736430
$87.67 MSRP: $137.33
You Save: $49.66 (37%)
ADD TO CART
Product Specifications
- Other Name: Mount, Transmission Mounting; Engine Mount Bracket; Transfer Case Mount; Motor Mount; Front Mount; Front Bracket; Mount
- Position: Front
- Replaces: 25706431
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1999-2005 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Transmission Mount Part Number: 22201116
Product Specifications
- Other Name: Mount, Transmission Mounting; Engine Mount Bracket; Transfer Case Mount; Motor Mount; Rear Mount; Mount
- Position: Rear
- Replaces: 22175200, 22174946, 22201115, 22171613
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1998 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Motor Mount, Passenger Side Part Number: 25710672
Product Specifications
- Other Name: Mount; Engine Mount Bracket; Transfer Case Mount; Transmission Mount; Mount, Engine Mount Dampening; Mount, Engine Mounting
- Position: Passenger Side
- Replaces: 25638464, 25681326, 25715770, 25695085, 25695931, 25691731, 25713699
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Motor Mount Part Number: 22146628
Product Specifications
- Other Name: Mount Assembly-Engine; Engine Mount Bracket; Engine Mount; Front Mount; Mount; Mount, Engine Mount Dampening
- Replaces: 22145817, 22185818
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1996 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Transmission Mount, Driver Side Part Number: 25695932
Product Specifications
- Other Name: Trans Mount; Engine Mount Bracket; Transfer Case Mount; Motor Mount; Side Transmission Mount; Mount; Mount, Transmission Mounting
- Position: Driver Side
- Replaces: 25662258, 25691733, 25689177, 25713700
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Transmission Mount, Driver Side Part Number: 22188869
Product Specifications
- Other Name: Mount, Transmission Mounting; Engine Mount Bracket; Transfer Case Mount; Motor Mount; Rear Mount; Mount
- Position: Driver Side
- Replaces: 22113356, 22113106
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1993 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Front Mount Part Number: 22201112
Product Specifications
- Other Name: Mount, Transmission Mounting; Engine Mount Bracket; Motor Mount
- Position: Front
- Replaces: 22173103
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1998 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Mount Bracket Part Number: 22112242
Product Specifications
- Other Name: Bracket, Engine Mounting; Engine Mount Torque Strut; Engine Mount Bracket; Motor Mount; Motor Mount Bracket; Support
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1994 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Transmission Mount Part Number: 22175154
Product Specifications
- Other Name: Mount, Transmission Mounting; Engine Mount Bracket; Transfer Case Mount; Engine Mount; Motor Mount; Front Mount
- Replaces: 22146339
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Transmission Mount Bracket Part Number: 25635776
Product Specifications
- Other Name: Bracket; Engine Mount Torque Strut; Engine Mount Bracket; Transfer Case Mount; Transmission Mount; Motor Mount; Rear Mount Bracket; Bracket, Transmission Mounting Support
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1998 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Rear Mount Bracket Part Number: 25677169
Product Specifications
- Other Name: Bracket; Engine Mount Bracket; Motor Mount; Rear Bracket; Bracket, Transmission Mounting Support
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1999-2005 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Engine Bracket, Driver Side Part Number: 25620949
Product Specifications
- Other Name: Support, Engine Mounting; Engine Mount Bracket; Engine Support Brace; Front Support; Reinforcement Support; Side Rail Reinforcement; Side Rail Support; Support
- Position: Driver Side
- Replaces: 25623908
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1996 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Engine Bracket, Passenger Side Part Number: 20416932
Product Specifications
- Other Name: Support, Engine Mounting; Engine Mount Bracket; Engine Support Brace; Front Support; Reinforcement Support; Side Rail Reinforcement; Side Rail Support; Support
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1991-1996 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Mount Bracket Part Number: 22145664
Product Specifications
- Other Name: Bracket, Engine Mounting; Engine Mount Bracket; Motor Mount; Motor Mount Bracket; Support
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Mount Bracket Part Number: 25685989
Product Specifications
- Other Name: Bracket, Engine Mounting; Engine Mount Bracket; Motor Mount; Motor Mount Bracket; Support
- Replaces: 22145826
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1996 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Support Part Number: 25665830
Product Specifications
- Other Name: Bracket, Engine Mounting
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1997-1999 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Transmission Mount Part Number: 25695084
Product Specifications
- Other Name: Mount, Transmission Mounting; Transfer Case Mount
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1999 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Support Part Number: 25740662
Product Specifications
- Other Name: Bracket, Engine Mounting; Engine Mount Bracket; Transmission Mount; Motor Mount; Bracket
- Replaces: 25647356
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2005 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS
View related parts
Buick Park Avenue Transmission Mount, Driver Side Part Number: 22146441
Product Specifications
- Other Name: Mount, Transmission Mounting; Engine Mount Bracket; Transfer Case Mount; Motor Mount; Rear Mount
- Position: Driver Side
- Replaces: 22145828, 17999341
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1996 Buick Park Avenue | Base, Ultra | 6 Cyl 3.8 L GAS

| Page 1 of 2 |Next >

1-20 of 23 Results

Buick Park Avenue Motor And Transmission Mount

Want to cut long-term maintenance and repair costs? Choose OEM Motor And Transmission Mount. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Buick Park Avenue parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Buick Park Avenue Motor And Transmission Mount includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

The Buick Park Avenue Motor And Transmission Mount is a critical part, which when installed greatly upgrades the Buick Park Avenue's reliability as well as its performance. Hailed for it remarkable sturdiness, this Motor And Transmission Mount facilitates the transmission and, at the same time, helps to dampen the centrifugal force generated by the engine in order to make the operation of a vehicle comfortable. This is specific for different Buick Park Avenue model and contributes into maintaining car's performance and safety by controlling shifting of the transmission that can cause its wear over time. Several elements common with today's cars are applied in the Buick Park Avenue Motor And Transmission Mount so that the material used will be durable as well as offer efficiency to the car. This feature is of most value to those drivers who prefer comfortable and distinctly noiseless ride since it effectively reduces noise and vibrations. Likewise, Motor And Transmission Mount has been designed to provide resilience on day-to-day usage to those Buick Park Avenue users. Its relevance in the auto industry is evident by the fact that accurate positioning of engine and most of the power transmission components is critical in the automobile industry. In summing up, Buick Park Avenue Motor And Transmission Mount is considered as highly reliable and compatible with the most Buick Park Avenue models; besides, it plays the crucial role in the improving of the car performance and safety.

Buick Park Avenue Motor And Transmission Mount Parts and Q&A

Transmission Mount, Driver Side
25695932
Q: How to service and repair the front motor and transmission mount on Buick Park Avenue?
A:
Begin transmission mount servicing and repair by removing the front transmission mount bracket followed by vehicle elevation and support. Start by removing the nut that holds the front transmission mount to the frame followed by vehicle lowering and front transmission mount extraction. You need to pass the front transmission mount's long stud through the frame hole using a hoisted vehicle. When your work is complete, reinstall the front transmission mount at the frame using a 70 Nm (52 ft. lbs.) torque setting on the nut. Repositioning the front transmission mount bracket should be the final step after lowering the vehicle.
Transmission Mount
25736430
Q: How to replace the LH Motor and Transmission Mount on Buick Park Avenue?
A:
In order to change the left transmission mount, lift and support the vehicle together with the removal of the left front tire, wheel and left front fascia extension. Set an assembly stand under the transaxle in order to towel the powertrain and take off the mount stud nut from the mount stud to detach the mount from the mount bracket. Then take off the nut, bolt and nuts from the vehicle, slowly bring down the transaxle stand and remove it. Lower and remove the retaining screws for the frame rail bolt before lifting the vehicle again. Push up on the frame rail bolts to clear the mount as the top of the mount tilts away from the vehicle and then remove the mount. For installation, put the mount stud into the transaxle mount bracket, lift the frame rail support bolts out of the mount while making rotations to position, and make sure to align and insert the loose frame rail support bolts into the mount. Lower the vehicle and install the frame rail bolt retaining screws, tightened to 4 Nm (35 inch lbs.). Lift up the vehicle again; fix the mount bolt and turn it in a counterclockwise direction to fix the anti-rotation tab behind the mount bracket, and the mount nuts, tightening these to 70 Nm (52 ft. lbs.). Position the powertrain on the transaxle stand and load the mount, then apply the mount stud nut tightly to 80 Nm (59 ft. lbs.). Remove the transaxle stand and reintroduce the left front fascia extension, the left front tire and wheel, and finally lower the vehicle.