How to replace the right engine mount bracket on Buick LaCrosse?

The replacement of right Engine Mount brackets begins by taking out the Engine Mount and upper nuts attached to the Engine Mount. The second step requires you to separate the Engine Mount Bracket from its connection with the Engine Mount. The installation process begins with mounting the Engine Mount Bracket to the Engine Mount while following the fastener notice in service precautions then fasten the upper nuts to 53 nm (39 ft. Lbs.). Finally, reinstall the Engine Mount.

How to replace the Engine Mount Bracket on Buick Regal?

The replacement process for Engine Mount and bracket starts with disconnecting the negative Battery Cable followed by removing the fuel injector sight shield then the Drive Belt. Prior to removal the technician will disconnect the electrical connector of intake air temperature (IAT) sensor and separate the air inlet duct from the Throttle Body. By disconnecting the right and left Engine Mount struts you should lift and support the vehicle from there. Start by removing the right front wheel and tire and then uninstall the right engine splash shield retainers along with its splash shield. The power steering oil cooler pipe brackets need to be detached from the frame before removing the A/C Compressor together with its mounting bracket which must be secured after completing the discharge process on the system. First remove the Catalytic Converter situated on the right side Exhaust Manifold then detach the Engine Mount lower nuts which fasten into the frame assembly. The installation of engine support fixture j 28467-b shall proceed after lowering the vehicle to lift the engine. Raising the vehicle enables workers to remove the left front Engine Mount bracket bolts and right rear Engine Mount bracket bolts that secure the engine. First secure the frame with jack stands afterward loosen the bolts on the left frame side before removing the right side bolts to lower the frame down for Engine Mount bracket removal. Complete the process by installing the Engine Mount to the Engine Mount bracket after removing the bracket and Engine Mount and the upper Engine Mount nuts. Fasten the Engine Mount upper nuts to 78 nm (58 ft. Lbs.) before installing the Engine Mount alongside bracket to the engine. Start with hand tightening the bracket bolts at the right rear and left front positions before finishing with bolt torque at 102 nm (75 ft. Lbs.). Put the frame in its normal position by using jack stands and apply torque of 180 nm (133 ft. Lbs.) to both right and left side frame bolts. Begin with a vehicle elevation then perform engine descent using the engine support fixture (J 28467-90A). Repeat the lifting process after which install the frame-side Engine Mount nuts and apply torque until reaching 78 nm at 58 ft. Lbs. Begin by installing the A/C Compressor bracket before adding bolts which need a torque of 50 nm (37 ft. Lbs.). Move on to install the A/C Compressor along with mounting nuts secured at 30 nm (22 ft. Lbs.). The power steering oil cooler pipe brackets should be reinstalled to the frame while the right engine splash shield and retainers along with the Catalytic Converter are positioned to the right side Exhaust Manifold. Finally place the proper front right tire along with its wheel onto the vehicle and lower it down while removing the support fixture for the engine and then reinstall the struts which support the engine before positioning the fuel injector sight shield in place and reestablish the negative Battery Cable connection. The general procedure ends with an air inlet duct installation to the Throttle Body and the connection of iat sensor electrical wiring followed by Drive Belt fitting and replacement of the fuel injector sight shield before reattaching the negative Battery Cable.

OEM Buick Engine Mount Bracket

Engine Mount

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

193 Engine Mount Brackets found

View related parts
Buick Mount Bracket Part Number: 12594433
$30.60 MSRP: $61.44
You Save: $30.84 (51%)
ADD TO CART
Product Specifications
- Other Name: Bracket-Engine Mount Strut & Engine Lift; Engine Mount Bracket; Transmission Mount; Motor Mount
- Replaces: 10154776, 12570320
Fits the following Buick Models:
- Century | 1997-2005 | Custom, Limited, Special Edition | 6 Cyl 3.1 L GAS
- Rendezvous | 2002-2007 | CX, CX Plus, CXL, CXL Plus | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L GAS
- Terraza | 2005-2007 | CX, CXL | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
View More
View related parts
Buick Motor Mount Part Number: 84034314
$89.49 MSRP: $156.17
You Save: $66.68 (43%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Mount Assembly-Engine; Engine Mount Bracket; Transmission Mount
- Replaces: 23438167, 23356077
Fits the following Buick Models:
- Regal Sportback | 2018-2020 | Avenir, Base, Essence, Preferred, Preferred II | 4 Cyl 2.0 L GAS
- Regal TourX | 2018-2020 | Base, Essence, Preferred | 4 Cyl 2.0 L GAS
View related parts
Buick Strut Bracket Part Number: 10274661
$177.35 MSRP: $301.93
You Save: $124.58 (42%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket, Engine Mounting; Engine Torque Strut Mount; Engine Mount Bracket; Motor Mount; Strut Front Bracket; Engine Mount
Fits the following Buick Models:
- Rendezvous | 2002-2007 | CX, CX Plus, CXL, CXL Plus, Ultra | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L GAS
- Terraza | 2005-2007 | CX, CXL | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
View related parts
Buick Strut Mount Part Number: 10271462
$205.18 MSRP: $325.75
You Save: $120.57 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket, Engine Mounting; Engine Mount Torque Strut; Engine Torque Strut Mount; Engine Mount Bracket; Motor Mount; Strut Bracket; Lower Bracket; Strut Front Bracket
Fits the following Buick Models:
- LaCrosse | 2005-2009 | CX, CXL, CXS | 6 Cyl 3.6 L GAS, 6 Cyl 3.8 L GAS
- Regal | 1996-2004 | 25th Anniversary Edition, Custom, GS, GSE, Gran Sport, LS, LSE, Limited, Olympic Gold Edition | 6 Cyl 3.8 L GAS
View related parts
Buick Strut Bracket Part Number: 15115355
$27.52 MSRP: $43.10
You Save: $15.58 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket-Engine Mount Strut Engine Side; Engine Mount Bracket; Motor Mount; Side Bracket; Bracket, Engine Mounting
Fits the following Buick Models:
- Enclave | 2008 | CX, CXL | 6 Cyl 3.6 L GAS
View related parts
Buick Front Mount Bracket Part Number: 15115368
$49.04 MSRP: $76.83
You Save: $27.79 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket, Engine Mounting
- Position: Front
Fits the following Buick Models:
- Enclave | 2008 | CX, CXL | 6 Cyl 3.6 L GAS
View related parts
Buick Mount Bracket Part Number: 95073703
$50.59 MSRP: $80.27
You Save: $29.68 (37%)
ADD TO CART
Product Specifications
- Other Name: Bracket, Engine Mounting; Engine Mount Bracket; Motor Mount
Fits the following Buick Models:
- Encore | 2013-2021 | Base, Convenience, Essence, Leather, Preferred, Preferred II, Premium, Sport Touring | 4 Cyl 1.4 L GAS
View related parts
Buick Motor Mount Bracket, Driver Side Part Number: 15062379
$100.58 MSRP: $157.55
You Save: $56.97 (37%)
Product Specifications
- Other Name: Bracket, Engine Mounting
- Position: Driver Side
Fits the following Buick Models:
- Rainier | 2004-2007 | CXL, CXL Plus | 6 Cyl 4.2 L GAS
View related parts
Buick Strut Mount Part Number: 10345904
$112.44 MSRP: $176.94
You Save: $64.50 (37%)
Product Specifications
- Other Name: Bracket, Engine Mounting; Engine Mount Torque Strut; Engine Torque Strut Mount; Engine Mount Bracket; Motor Mount
Fits the following Buick Models:
- LaCrosse | 2008-2009 | Super | 8 Cyl 5.3 L GAS
View related parts
Buick Rear Mount Bracket Part Number: 25840455
$118.98 MSRP: $187.20
You Save: $68.22 (37%)
Product Specifications
- Other Name: Bracket, Engine Mounting; Engine Mount Torque Strut; Engine Mount Bracket; Engine Torque Mount; Motor Mount
- Position: Rear
Fits the following Buick Models:
- Enclave | 2009-2017 | Base, CX, CXL, Convenience, Leather, Premium | 6 Cyl 3.6 L GAS
View related parts
Buick Motor Mount, Rear Part Number: 22637949
Product Specifications
- Other Name: Mount Assembly-Engine Rear; Engine Mount Torque Strut; Engine Mount Bracket
- Position: Rear
- Replaces: 22579308, 22638595
Fits the following Buick Models:
- Skyhawk | 1984-1989 | Custom, Limited, SE, Sport, T-Type | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS
- Skylark | 1985-1991 | Base, Custom, Gran Sport, Limited, Luxury Edition | 4 Cyl 2.5 L GAS
- Somerset | 1986-1987 | Custom, Limited, T-Type | 4 Cyl 2.5 L GAS
- Somerset Regal | 1985 | Base, Limited | 4 Cyl 2.5 L GAS
View More
View related parts
Buick Mount Bracket Part Number: 10216970
Product Specifications
- Other Name: Bracket, Engine Mounting; Engine Mount Bracket; Transmission Mount; Motor Mount; Engine Bracket; Lower Bracket; Bracket
Fits the following Buick Models:
- Century | 1997-2004 | Custom, Limited | 6 Cyl 3.1 L GAS
- Regal | 1994-1996 | Custom | 6 Cyl 3.1 L GAS
- Rendezvous | 2002-2007 | CX, CX Plus, CXL, CXL Plus | 6 Cyl 3.4 L GAS, 6 Cyl 3.5 L GAS
- Terraza | 2005-2007 | CX, CXL | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
View More
View related parts
Buick Mount Bracket Part Number: 10345562
Product Specifications
- Other Name: Bracket, Engine Mounting; Engine Mount Bracket; Motor Mount
Fits the following Buick Models:
- Century | 2005 | Custom, Limited, Special Edition | 6 Cyl 3.1 L GAS
- LaCrosse | 2005-2009 | CX, CXL | 6 Cyl 3.8 L GAS
View related parts
Buick Mount Bracket Part Number: 10321856
Product Specifications
- Other Name: Bracket, Engine Mounting; Engine Mount Bracket; Transmission Mount; Motor Mount; Engine Bracket; Bracket
- Replaces: 10243884
Fits the following Buick Models:
- Regal | 1996-2004 | 25th Anniversary Edition, Custom, GS, GSE, Gran Sport, LS, LSE, Limited, Olympic Gold Edition | 6 Cyl 3.8 L GAS
View related parts
Buick Front Mount Bracket Part Number: 25886948
Product Specifications
- Other Name: Bracket-Engine Front Mount; Bracket, Engine Mounting
- Position: Front
Fits the following Buick Models:
- Lucerne | 2009-2011 | CX, CXL, CXL Special Edition | 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
View related parts
Buick Strut Support Part Number: 24504704
Product Specifications
- Other Name: Support, Engine Mounting; Engine Mount Torque Strut; Engine Mount Bracket; Motor Mount; Mount Support; Support
Fits the following Buick Models:
- Skylark | 1994-1998 | Custom, Gran Sport, Limited, Olympic Gold Edition | 6 Cyl 3.1 L GAS
View related parts
Buick Strut Bracket Part Number: 15936657
Product Specifications
- Other Name: Bracket-Engine Mount Strut Engine Side; Engine Mount Bracket; Motor Mount; Side Bracket; Bracket, Engine Mounting
Fits the following Buick Models:
- Enclave | 2008 | CX, CXL | 6 Cyl 3.6 L GAS
View related parts
Buick Motor Mount Bracket, Passenger Side Part Number: 15062380
Product Specifications
- Other Name: Bracket, Engine Mounting
- Position: Passenger Side
Fits the following Buick Models:
- Rainier | 2004-2007 | CXL, CXL Plus | 6 Cyl 4.2 L GAS
View related parts
Buick Strut Bracket, Driver Side Part Number: 24503458
Product Specifications
- Other Name: Bracket, Engine Lift; Engine Mount Bracket; Transmission Mount; Motor Mount
- Position: Driver Side
Fits the following Buick Models:
- LaCrosse | 2005-2009 | CX, CXL | 6 Cyl 3.8 L GAS
- Regal | 1996-2004 | 25th Anniversary Edition, Custom, GS, GSE, Gran Sport, LS, LSE, Limited, Olympic Gold Edition | 6 Cyl 3.8 L GAS
View related parts
Buick Motor Mount, Passenger Side Part Number: 25710672
Product Specifications
- Other Name: Mount; Engine Mount Bracket; Transfer Case Mount; Transmission Mount
- Position: Passenger Side
- Replaces: 25713699, 25695085, 25691731, 25638464, 25681326, 25715770, 25695931
Fits the following Buick Models:
- LeSabre | 2000-2005 | Custom, Limited | 6 Cyl 3.8 L GAS
- Park Avenue | 2000-2005 | Base, Ultra | 6 Cyl 3.8 L GAS

| Page 1 of 10 |Next >

1-20 of 193 Results

Buick Engine Mount Bracket

Choose OEM Engine Mount Bracket, you're making the optimal decision for superior quality and perfect performance. You can feel confident because each component goes through stringent quality checks. Every part is carefully built to comply with Buick's factory specifications. You'll enjoy a smooth, worry-free installation that fits just right. At ChevyPartsDeal.com, you'll find it easy to get top-quality OEM Buick Engine Mount Bracket. You can shop at highly competitive prices and protect your budget. All our genuine Buick parts include a dependable manufacturer's warranty. You'll also appreciate our straightforward return policy and swift delivery services for extra convenience.

Buick Engine Mount Bracket eliminates engine vibration and the power plant is fixed firmly in place during each drive. Throughout over 100 years of existence, Buick has pursued quiet cabins, soft ride quality, and new technology without abandoning its heritage. It pioneered quiet tuning long before the luxury competitors followed suit and demonstrated a sense of practical elegance. Drivers acquired comfortably cushy seats, readable gauges, and smooth power that made long journeys feel short. The company continues that run today with traditional waterfall grille hints, sculpted lines of LEDs, and the eye-catching Wildcat EV concept. In a nutshell, the badge continues to be one of calm confidence as opposed to screamers and gimmicks. Owners understand that the car will be an easy ride through its daily errands and intrastate loads. The Engine Mount Bracket attaches to the chassis and creates the rigid connection, which holds the engine and transaxle, eliminating vibration before it gets to the firewall. The bracket accommodates the changing load and rpm requirements without drama by taking standard rubber, hydraulic, and adaptive electronic mounts. Its heavy cast steel shields of sheet metal resist twisting, thus steering is true and parts are longer lasting. Early corrosive checking is made by regular checks, since the weakened Engine Mount Bracket is an invitation to shudder that can avalanche into expensive fatigue. Insert another unit and the car will follow the straight line, will not vibrate, and will make passengers comfortable. It is a mere exchange that keeps Buick on its feet in the coming years.

Buick Engine Mount Bracket Parts and Q&A

Strut Mount
10271462
Q: How to replace the right engine mount bracket on Buick LaCrosse?
A:
The replacement of right Engine Mount brackets begins by taking out the Engine Mount and upper nuts attached to the Engine Mount. The second step requires you to separate the Engine Mount Bracket from its connection with the Engine Mount. The installation process begins with mounting the Engine Mount Bracket to the Engine Mount while following the fastener notice in service precautions then fasten the upper nuts to 53 nm (39 ft. Lbs.). Finally, reinstall the Engine Mount.
Mount Bracket
10321856
Q: How to replace the Engine Mount Bracket on Buick Regal?
A:
The replacement process for Engine Mount and bracket starts with disconnecting the negative Battery Cable followed by removing the fuel injector sight shield then the Drive Belt. Prior to removal the technician will disconnect the electrical connector of intake air temperature (IAT) sensor and separate the air inlet duct from the Throttle Body. By disconnecting the right and left Engine Mount struts you should lift and support the vehicle from there. Start by removing the right front wheel and tire and then uninstall the right engine splash shield retainers along with its splash shield. The power steering oil cooler pipe brackets need to be detached from the frame before removing the A/C Compressor together with its mounting bracket which must be secured after completing the discharge process on the system. First remove the Catalytic Converter situated on the right side Exhaust Manifold then detach the Engine Mount lower nuts which fasten into the frame assembly. The installation of engine support fixture j 28467-b shall proceed after lowering the vehicle to lift the engine. Raising the vehicle enables workers to remove the left front Engine Mount bracket bolts and right rear Engine Mount bracket bolts that secure the engine. First secure the frame with jack stands afterward loosen the bolts on the left frame side before removing the right side bolts to lower the frame down for Engine Mount bracket removal. Complete the process by installing the Engine Mount to the Engine Mount bracket after removing the bracket and Engine Mount and the upper Engine Mount nuts. Fasten the Engine Mount upper nuts to 78 nm (58 ft. Lbs.) before installing the Engine Mount alongside bracket to the engine. Start with hand tightening the bracket bolts at the right rear and left front positions before finishing with bolt torque at 102 nm (75 ft. Lbs.). Put the frame in its normal position by using jack stands and apply torque of 180 nm (133 ft. Lbs.) to both right and left side frame bolts. Begin with a vehicle elevation then perform engine descent using the engine support fixture (J 28467-90A). Repeat the lifting process after which install the frame-side Engine Mount nuts and apply torque until reaching 78 nm at 58 ft. Lbs. Begin by installing the A/C Compressor bracket before adding bolts which need a torque of 50 nm (37 ft. Lbs.). Move on to install the A/C Compressor along with mounting nuts secured at 30 nm (22 ft. Lbs.). The power steering oil cooler pipe brackets should be reinstalled to the frame while the right engine splash shield and retainers along with the Catalytic Converter are positioned to the right side Exhaust Manifold. Finally place the proper front right tire along with its wheel onto the vehicle and lower it down while removing the support fixture for the engine and then reinstall the struts which support the engine before positioning the fuel injector sight shield in place and reestablish the negative Battery Cable connection. The general procedure ends with an air inlet duct installation to the Throttle Body and the connection of iat sensor electrical wiring followed by Drive Belt fitting and replacement of the fuel injector sight shield before reattaching the negative Battery Cable.