How to replace the front brake calipers on Buick Regal?

Before removing the front brake caliper you need to check the brake fluid level in the reservoir. Drain the fluid if it stands above the middle line between the two allowed measurement marks. Support the vehicle safely while lifting it and detach the front tire together with its wheel assembly. Install a large c-clamp above the brake caliper while hand tightening two wheel lug nuts to prevent the rotor from detaching from the hub. Once done tighten the c-clamp until the caliper piston moves into position for easy removal of the brake caliper from the rotor. Take out the brake hose-to-caliper bolt along with both copper gaskets and set them aside. Apply a cap onto the brake hose ending to stop fluid leakage while making sure not to crush the hose with tools. Take the caliper bolts out and move the caliper away from the rotor when it is still attached to its bracket. Check the caliper boot space in the bracket for damage like cuts and tears. Replace the boots when problems are found and replace all caliper bolts if their condition is poor or imperfect. Wipe the brake caliper pin bolts and retainers with denatured alcohol before applying non-lubricated filtered air. Then spread high temperature silicone brake lubricant on the bolt and retainer pins while keeping the pad hardware free of lubricant. Thread the caliper over the rotor wheel and bracket while making sure bushings fill their locations before applying silicone grease to caliper bolts except their threaded parts. Insert the caliper bolts and make sure the boots of bolt pass through the grooves of pin bolts without damaging or distorting them before tightening them to 95 nm (70 ft. Lbs.). Install new copper brake hose gaskets onto the brake hose bolt and gaskets before fitting them to the brake hose. Then tighten the brake hose-to-caliper bolt to 54 nm (40 ft. Lbs.). Lower your car after installing the front tire and wheel then remove the two lug nuts connecting the rotor to the hub. Now fill your master cylinder with brake fluid until it reaches the correct level while examining hydraulic brake system leaks.

How to replace the rear brake calipers on Buick LaCrosse?

To replace the rear brake caliper one has to first check the fluid level in the brake master cylinder reservoir; if it is at or above the midway point between maximum-full and minimum allowable levels, discard fluid to the midway point. Lift and support the vehicle and also remove the tire and wheel assembly. Let off pressure from the park brake system at the equalizer and remove the front and rear cables at the connector clip. Remove the park brake cable from the park brake lever connected on the brake caliper as well as the caliper bracket. Detach brake hose to caliper bolt, and remove the brake hose from brake caliper then discard the 2 copper brake hose gaskets. Plug the holes in the brake caliper and brake hose to avoid losing and contaminating the fluid, then remove the brake caliper bolts and caliper. For installation line up the indentions on the piston face with the pin on the Brake Pad, and check bracket bolt guide assembly, and Brake Pad hardware and brake caliper on to the caliper bracket and make sure the guide boots are not damaged. Mount the brake caliper bolts and tighten them to 34 (Nm 25 lb ft). Unscrew the plugs at the end of the brake hose and install new copper brake hose gaskets after which assemble the brake hose bolt with the new gaskets onto the brake hose. Mount the brake hose to the caliper bolt to the brake caliper, with the hose held up as the nut is tightened to 54 n.m (40 lb ft). Mount the park brake cable onto the park brake bracket of the caliper and link it to the park brake lever. Bleed brake system: slowly press the pedal down to 2/3 travel distance, then release, repeat until a firm pedal should be gained and the engine is off. Modify the park brake system, re-install the tire and wheel assembly, and drive the vehicle down.

OEM Buick Brake Calipers

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

151 Brake Calipers found

View related parts
Buick Caliper, Silver, Rear Passenger Side Part Number: 22796445
$294.41 MSRP: $560.62
You Save: $266.21 (48%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing Assembly-Rear Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Rear Passenger Side
Fits the following Buick Models:
- Regal | 2014-2017 | Base, GS, Premium, Sport Touring | 4 Cyl 2.0 L GAS, 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS, 4 Cyl 2.4 L MILD HYBRID EV-GAS (MHEV)
View related parts
Buick Caliper, Front Part Number: 19141350
$54.14 MSRP: $98.79
You Save: $44.65 (46%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly, Front Brake (W/O Brake Pads) (Remanufacture); Brake Caliper
- Position: Front
- Replaces: 18021163, 18039664
Fits the following Buick Models:
- Roadmaster | 1994-1996 | Base, Collector's Edition, Estate Wagon, Estate Wagon Collector's Edition, Limited, Limited Collector's Edition | 8 Cyl 5.7 L GAS
View related parts
Buick Caliper Part Number: 18015755
$50.98 MSRP: $97.81
You Save: $46.83 (48%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Front
- Replaced by: 19140953
Fits the following Buick Models:
- Century | 1984-1990 | Custom, Estate Wagon, Limited, T-Type | 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L DIESEL
- Electra | 1985-1989 | Limited, Park Avenue, Park Avenue Ultra, T-Type | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L DIESEL
- LeSabre | 1986-1989 | Base, Custom, Limited, T-Type | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View More
View related parts
Buick Caliper, Front Passenger Side Part Number: 19141029
$53.78 MSRP: $98.14
You Save: $44.36 (46%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly, Front Brake (W/O Brake Pads) (Remanufacture); Brake Caliper; Caliper Kit, Wheel Brake Cylinder/Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Passenger Side
- Replaces: 18036713, 18021841, 18060191, 18017232
Fits the following Buick Models:
- Century | 1991-1996 | Custom, Limited, Special | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.1 L GAS, 6 Cyl 3.3 L GAS
- Electra | 1990 | Limited, Park Avenue, Park Avenue Ultra, T-Type | 6 Cyl 3.8 L GAS
- LeSabre | 1990-1991 | Base, Custom, Limited | 6 Cyl 3.8 L GAS
View More
View related parts
Buick Caliper Part Number: 18017231
$53.78 MSRP: $98.14
You Save: $44.36 (46%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper A; Brake Caliper
- Replaced by: 19141028
Fits the following Buick Models:
- Century | 1991 | Custom, Limited, Special | 4 Cyl 2.5 L GAS, 6 Cyl 3.3 L GAS
- Electra | 1990 | Limited, Park Avenue, Park Avenue Ultra, T-Type | 6 Cyl 3.8 L GAS
- LeSabre | 1990-1991 | Base, Custom, Limited | 6 Cyl 3.8 L GAS
View More
View related parts
Buick Caliper, Front Driver Side Part Number: 19141028
$53.78 MSRP: $98.14
You Save: $44.36 (46%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly, Front Brake (W/O Brake Pads) (Remanufacture); Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Driver Side
- Replaces: 18017231, 18060190, 18036714
Fits the following Buick Models:
- Century | 1991-1996 | Custom, Limited, Special | 4 Cyl 2.2 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.1 L GAS, 6 Cyl 3.3 L GAS
- Electra | 1990 | Limited, Park Avenue, Park Avenue Ultra, T-Type | 6 Cyl 3.8 L GAS
- LeSabre | 1990-1991 | Base, Custom, Limited | 6 Cyl 3.8 L GAS
View More
View related parts
Buick Caliper, Front Part Number: 19141351
$54.14 MSRP: $98.79
You Save: $44.65 (46%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly, Front Brake (W/O Brake Pads) (Remanufacture); Brake Caliper
- Position: Front
- Replaces: 18021162, 18037480, 18039665
Fits the following Buick Models:
- Roadmaster | 1994-1996 | Base, Collector's Edition, Estate Wagon, Estate Wagon Collector's Edition, Limited, Limited Collector's Edition | 8 Cyl 5.7 L GAS
View related parts
Buick Caliper, Front Part Number: 19140969
$46.08 MSRP: $84.05
You Save: $37.97 (46%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly, Front Brake (W/O Brake Pads) (Remanufacture); Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front
- Replaces: 18036564, 18060113, 18015753
Fits the following Buick Models:
- Century | 1984-1989 | Custom, Estate Wagon, Limited, T-Type | 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L DIESEL
- Skyhawk | 1984-1989 | Custom, Limited, SE, Sport, T-Type | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS
- Skylark | 1984-1989 | Custom, Limited, T-Type | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS
- Somerset | 1986-1987 | Custom, Limited, T-Type | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS
- Somerset Regal | 1985 | Base, Limited | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS
View More
View related parts
Buick Caliper, Front Part Number: 19140968
$46.08 MSRP: $84.02
You Save: $37.94 (46%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly, Front Brake (W/O Brake Pads) (Remanufacture); Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front
- Replaces: 18015752, 18060112, 18036565
Fits the following Buick Models:
- Century | 1984-1989 | Custom, Estate Wagon, Limited, T-Type | 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L DIESEL
- Skyhawk | 1984-1989 | Custom, Limited, SE, Sport, T-Type | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS
- Skylark | 1984-1989 | Custom, Limited, T-Type | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS
- Somerset | 1986-1987 | Custom, Limited, T-Type | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS
- Somerset Regal | 1985 | Base, Limited | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS
View More
View related parts
Buick Caliper Assembly, Front Driver Side Part Number: 19140966
$50.00 MSRP: $91.20
You Save: $41.20 (46%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly, Front Brake (W/O Brake Pads) (Remanufacture); Brake Caliper; Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Driver Side
- Replaces: 18036581
Fits the following Buick Models:
- Reatta | 1988-1991 | Base | 6 Cyl 3.8 L GAS
- Riviera | 1986-1991 | Luxury, T-Type | 6 Cyl 3.8 L GAS
View related parts
Buick Caliper Assembly, Front Part Number: 19141283
$48.90 MSRP: $89.20
You Save: $40.30 (46%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly, Front Brake (W/O Brake Pads) (Remanufacture); Brake Caliper; Caliper
- Position: Front
- Replaces: 18060165, 18037092, 18018730
Fits the following Buick Models:
- LeSabre | 1992-1993 | Custom, Limited | 6 Cyl 3.8 L GAS
- Park Avenue | 1991-1993 | Base, Ultra | 6 Cyl 3.8 L GAS
- Riviera | 1992-1993 | Luxury | 6 Cyl 3.8 L GAS
View More
View related parts
Buick Caliper, Front Passenger Side Part Number: 19140953
$53.60 MSRP: $97.81
You Save: $44.21 (46%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly, Front Brake (W/O Brake Pads) (Remanufacture); Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Front Passenger Side
- Replaces: 18015755, 18060089, 18013999, 18036562
Fits the following Buick Models:
- Century | 1984-1991 | Custom, Estate Wagon, Limited, Special, T-Type | 4 Cyl 2.5 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.3 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L DIESEL
- Electra | 1985-1989 | Limited, Park Avenue, Park Avenue Ultra, T-Type | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L DIESEL
- LeSabre | 1986-1989 | Base, Custom, Limited, T-Type | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View More
View related parts
Buick Caliper, Passenger Side Part Number: 13588973
$49.17 MSRP: $92.34
You Save: $43.17 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Passenger Side
Fits the following Buick Models:
- Encore | 2018-2022 | Base, Essence, Preferred, Preferred II, Premium, Sport Touring | 4 Cyl 1.4 L GAS
View related parts
Buick Caliper, Rear Driver Side Part Number: 13532621
$28.76 MSRP: $52.06
You Save: $23.30 (45%)
ADD TO CART
Product Specifications
- Other Name: Caliper Assembly-Rear Brake (W/O Brake Pads & Bracket); Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Rear Driver Side
Fits the following Buick Models:
- Encore GX | 2020-2024 | Avenir, Essence, Preferred, Select, Sport Touring | 3 Cyl 1.2 L GAS, 3 Cyl 1.3 L GAS
View related parts
Buick Caliper Overhaul Kit Part Number: 3487729
Product Specifications
- Other Name: Caliper Repair Kit; Brake Caliper Repair Kit; Disc Brake Hardware Kit; Caliper Kit, Wheel Brake Cylinder/Caliper
Fits the following Buick Models:
- Regal | 1988-1993 | Custom, Gran Sport, Limited | 6 Cyl 2.8 L GAS, 6 Cyl 3.1 L GAS, 6 Cyl 3.8 L GAS
View related parts
Buick Caliper, Driver Side Part Number: 18060106
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Driver Side
- Replaces: 18015174
Fits the following Buick Models:
- Regal | 1988-1996 | Custom, Gran Sport, Limited, Olympic Gold Edition | 6 Cyl 2.8 L GAS, 6 Cyl 3.1 L GAS, 6 Cyl 3.8 L GAS
View related parts
Buick Caliper, Rear Part Number: 3487819
Product Specifications
- Other Name: Caliper, Rear Brake; Brake Caliper
- Position: Rear
- Replaced by: 03494139
Fits the following Buick Models:
- Regal | 1989-1991 | Custom, Gran Sport, Limited | 6 Cyl 2.8 L GAS, 6 Cyl 3.1 L GAS, 6 Cyl 3.8 L GAS
View related parts
Buick Caliper, Driver Side Part Number: 3494138
Product Specifications
- Other Name: Caliper Assembly, Rear Brake; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Driver Side
Fits the following Buick Models:
- Regal | 1989-1993 | Custom, Gran Sport, Limited | 6 Cyl 2.8 L GAS, 6 Cyl 3.1 L GAS, 6 Cyl 3.8 L GAS
View related parts
Buick Caliper, Passenger Side Part Number: 3494139
Product Specifications
- Other Name: Caliper Assembly, Rear Brake; Brake Caliper; Caliper, Wheel Brake Cylinder/Caliper
- Position: Passenger Side
Fits the following Buick Models:
- Regal | 1989-1993 | Custom, Gran Sport, Limited | 6 Cyl 2.8 L GAS, 6 Cyl 3.1 L GAS, 6 Cyl 3.8 L GAS
View related parts
Buick Caliper, Driver Side Part Number: 13273623
Product Specifications
- Other Name: Caliper, Wheel Brake Cylinder/Caliper; Brake Caliper
- Position: Driver Side
Fits the following Buick Models:
- Regal | 2012-2013 | GS, Premium | 4 Cyl 2.0 L FLEX

| Page 1 of 8 |Next >

1-20 of 151 Results

Buick Brake Calipers

Choose OEM Brake Calipers, you're making the optimal decision for superior quality and perfect performance. You can feel confident because each component goes through stringent quality checks. Every part is carefully built to comply with Buick's factory specifications. You'll enjoy a smooth, worry-free installation that fits just right. At ChevyPartsDeal.com, you'll find it easy to get top-quality OEM Buick Brake Calipers. You can shop at highly competitive prices and protect your budget. All our genuine Buick parts include a dependable manufacturer's warranty. You'll also appreciate our straightforward return policy and swift delivery services for extra convenience.

Buick Brake Calipers firmly hold rotors in order to transform pedal force into rapid and self-confident halts. Buick started manufacturing vehicles in 1903, and the long history is significant as perfection is gained through experience. Drivers are aware of the ride remaining smooth in the road noise and the seats remaining supportive even after hours of being on the interstate. The QuietTuning glass, intelligent cabin insulation and balanced suspension ensure the voices are not muffled and fatigue is reduced. The firm maintains the tradition even as it implements the current trend such as the projection of a wireless phone and sharp digital gauges. The 2022 Wildcat EV concept teaser promises sharp lines and an all-electric future without sacrificing comfort. All the models have a simple purpose, to make the everyday commute easier, more comfortable and appear a bit more fashionable. Buick strikes a balance between that easy feel and one that is adjusted to regular highway tracking and smooth though easy parking in city environments. The rotor is clamped by Brake Calipers and the pads attach to steel which pushes the piston forcing the pads to rotate the wheel speed into heat where the driver can have instant and predictable braking power. Fixed designs are pack-style that have pistons on both sides that are rigidly constructed, rewarding smooth rotors with crisp pedal feel. Floating versions operate on pins, move the inner pad with one piston, and then pull the housing to squeeze the outer pad, thereby saving weight and cost. When that slide caused by dirt or corrosion prevents the caliper from dragging, pads become imbalanced, rotors become overheated and fuel economy becomes compromised. It is that free movement that is required of Brake Calipers in order to maintain strong braking and steering under all conditions.

Buick Brake Calipers Parts and Q&A

Caliper, Front Driver Side
18046200
Q: How to replace the front brake calipers on Buick Regal?
A:
Before removing the front brake caliper you need to check the brake fluid level in the reservoir. Drain the fluid if it stands above the middle line between the two allowed measurement marks. Support the vehicle safely while lifting it and detach the front tire together with its wheel assembly. Install a large c-clamp above the brake caliper while hand tightening two wheel lug nuts to prevent the rotor from detaching from the hub. Once done tighten the c-clamp until the caliper piston moves into position for easy removal of the brake caliper from the rotor. Take out the brake hose-to-caliper bolt along with both copper gaskets and set them aside. Apply a cap onto the brake hose ending to stop fluid leakage while making sure not to crush the hose with tools. Take the caliper bolts out and move the caliper away from the rotor when it is still attached to its bracket. Check the caliper boot space in the bracket for damage like cuts and tears. Replace the boots when problems are found and replace all caliper bolts if their condition is poor or imperfect. Wipe the brake caliper pin bolts and retainers with denatured alcohol before applying non-lubricated filtered air. Then spread high temperature silicone brake lubricant on the bolt and retainer pins while keeping the pad hardware free of lubricant. Thread the caliper over the rotor wheel and bracket while making sure bushings fill their locations before applying silicone grease to caliper bolts except their threaded parts. Insert the caliper bolts and make sure the boots of bolt pass through the grooves of pin bolts without damaging or distorting them before tightening them to 95 nm (70 ft. Lbs.). Install new copper brake hose gaskets onto the brake hose bolt and gaskets before fitting them to the brake hose. Then tighten the brake hose-to-caliper bolt to 54 nm (40 ft. Lbs.). Lower your car after installing the front tire and wheel then remove the two lug nuts connecting the rotor to the hub. Now fill your master cylinder with brake fluid until it reaches the correct level while examining hydraulic brake system leaks.
Caliper, Rear Driver Side
25990068
Q: How to replace the rear brake calipers on Buick LaCrosse?
A:
To replace the rear brake caliper one has to first check the fluid level in the brake master cylinder reservoir; if it is at or above the midway point between maximum-full and minimum allowable levels, discard fluid to the midway point. Lift and support the vehicle and also remove the tire and wheel assembly. Let off pressure from the park brake system at the equalizer and remove the front and rear cables at the connector clip. Remove the park brake cable from the park brake lever connected on the brake caliper as well as the caliper bracket. Detach brake hose to caliper bolt, and remove the brake hose from brake caliper then discard the 2 copper brake hose gaskets. Plug the holes in the brake caliper and brake hose to avoid losing and contaminating the fluid, then remove the brake caliper bolts and caliper. For installation line up the indentions on the piston face with the pin on the Brake Pad, and check bracket bolt guide assembly, and Brake Pad hardware and brake caliper on to the caliper bracket and make sure the guide boots are not damaged. Mount the brake caliper bolts and tighten them to 34 (Nm 25 lb ft). Unscrew the plugs at the end of the brake hose and install new copper brake hose gaskets after which assemble the brake hose bolt with the new gaskets onto the brake hose. Mount the brake hose to the caliper bolt to the brake caliper, with the hose held up as the nut is tightened to 54 n.m (40 lb ft). Mount the park brake cable onto the park brake bracket of the caliper and link it to the park brake lever. Bleed brake system: slowly press the pedal down to 2/3 travel distance, then release, repeat until a firm pedal should be gained and the engine is off. Modify the park brake system, re-install the tire and wheel assembly, and drive the vehicle down.