How to replace the outer CV Boot and CV Joint on the wheel drive shaft on 2009 Chevrolet HHR?

Before replacing the wheel drive shaft outer joint and boot clamp the drive Axle Shaft in a soft jawed vice while watching both boots to prevent damaging the vital sealing surface which causes premature wear. A flat-bladed tool should remove the boot clamp from the constant velocity (CV) joint and the boot. Discard both components before installing new clamps. The cv joint requires a wood block and hammer to detach from the drive shaft followed by removing the boot from the shaft to evaluate outer joint conditions. When installing the boot position it on the wheel drive shaft with care to have the boot rest fully inside the wheel drive shaft groove. A block of wood along with a hammer assists in installing the cv joint onto the wheel drive shaft while positioning approximately half of the lubricant within the boot and the cv joint separately. Begin boot assembly by adding the boot clamp to the boot section adjacent to the wheel drive shaft and the cv joint housing section of the boot. Maintain correct positioning for the entire boot circumference. Use the j 35910 - pliers to close the clamp until the gap reaches 2.15 mm (0.85 in). Following this, complete closure of the boot clamp using the ch 48894 - pliers. Before reinstallation, use the bench vise to extract the wheel drive shaft then guide the cv joint through four to five round movements for lubricant spreading before returning the shaft to the vehicle.

OEM 2009 Chevrolet HHR CV Boot

Axle Boot

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

8 CV Boots found

View related parts
2009 Chevrolet HHR Inner Boot, Front Part Number: 10359973
$33.28 MSRP: $81.20
You Save: $47.92 (60%)
ADD TO CART
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; CV Boot
- Position: Front
- Item Weight: 1.20 Pounds
- Item Dimensions: 7.4 x 5.2 x 3.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 10359973
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2009 Chevrolet HHR Submodels:
- LS, LS Panel, LT, LT Panel, SS, SS Panel | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS
View related parts
2009 Chevrolet HHR Boot Kit, Front Part Number: 10360041
$55.29 MSRP: $87.77
You Save: $32.48 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; CV Boot; Outer Boot
- Position: Front
- Item Weight: 1.20 Pounds
- Item Dimensions: 8.9 x 8.5 x 5.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 10360041
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2009 Chevrolet HHR Submodels:
- LS, LS Panel, LT, LT Panel, SS, SS Panel | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS
View related parts
2009 Chevrolet HHR Boot Kit, Green Line, Front Part Number: 25786428
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; CV Boot; Inner Boot; Outer Boot; Boots
- Position: Front
- Item Weight: 1.70 Pounds
- Item Dimensions: 6.9 x 6.2 x 6.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 25786428
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2009 Chevrolet HHR Submodels:
- SS, SS Panel | 4 Cyl 2.0 L GAS
View related parts
2009 Chevrolet HHR Inner Boot, Front Part Number: 10359813
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; CV Boot
- Position: Front
- Item Weight: 1.10 Pounds
- Item Dimensions: 7.3 x 5.1 x 3.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 10359813
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2009 Chevrolet HHR Submodels:
- LS, LS Panel, LT, LT Panel, SS, SS Panel | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS
View related parts
2009 Chevrolet HHR Boot Kit, Front Part Number: 10360040
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; CV Boot; Outer Boot
- Position: Front
- Item Weight: 1.20 Pounds
- Item Dimensions: 7.1 x 5.1 x 3.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 10360040
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2009 Chevrolet HHR Submodels:
- LS, LS Panel, LT, LT Panel, SS, SS Panel | 4 Cyl 2.0 L GAS, 4 Cyl 2.2 L FLEX, 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS
View related parts
2009 Chevrolet HHR Outer Boot, Front Part Number: 19181205
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Shaft CV Joint; CV Boot; Boot Kit, Front Wheel Drive Axle Shaft
- Position: Front
- Item Weight: 0.40 Pounds
- Item Dimensions: 4.9 x 4.6 x 4.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 19181205
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2009 Chevrolet HHR Submodels:
- SS, SS Panel | 4 Cyl 2.0 L GAS
View related parts
2009 Chevrolet HHR Boot Kit, Front Part Number: 22692206
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Axle Shaft; CV Boot; Inner Boot; Outer Boot; Boots
- Position: Front
- Item Weight: 1.50 Pounds
- Item Dimensions: 6.1 x 4.4 x 4.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 22692206
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2009 Chevrolet HHR Submodels:
- SS, SS Panel | 4 Cyl 2.0 L GAS
View related parts
2009 Chevrolet HHR Inner Boot, Front Part Number: 19181204
Product Specifications
- Other Name: Boot Kit, Front Wheel Drive Shaft Tri-Pot Joint; CV Boot; Boot Kit, Front Wheel Drive Axle Shaft
- Position: Front
- Item Weight: 0.50 Pounds
- Item Dimensions: 4.7 x 4.7 x 4.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- Require Quantity: 2
- SKU: 19181204
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2009 Chevrolet HHR Submodels:
- SS, SS Panel | 4 Cyl 2.0 L GAS

2009 Chevrolet HHR CV Boot

With a comprehensive array of OEM 2009 Chevrolet HHR CV Boot, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2009 Chevrolet HHR CV Boot are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.

2009 Chevrolet HHR CV Boot Parts and Q&A

Q: How to replace the outer CV Boot and CV Joint on the wheel drive shaft on 2009 Chevrolet HHR?
A: Before replacing the wheel drive shaft outer joint and boot clamp the drive Axle Shaft in a soft jawed vice while watching both boots to prevent damaging the vital sealing surface which causes premature wear. A flat-bladed tool should remove the boot clamp from the constant velocity (CV) joint and the boot. Discard both components before installing new clamps. The cv joint requires a wood block and hammer to detach from the drive shaft followed by removing the boot from the shaft to evaluate outer joint conditions. When installing the boot position it on the wheel drive shaft with care to have the boot rest fully inside the wheel drive shaft groove. A block of wood along with a hammer assists in installing the cv joint onto the wheel drive shaft while positioning approximately half of the lubricant within the boot and the cv joint separately. Begin boot assembly by adding the boot clamp to the boot section adjacent to the wheel drive shaft and the cv joint housing section of the boot. Maintain correct positioning for the entire boot circumference. Use the j 35910 - pliers to close the clamp until the gap reaches 2.15 mm (0.85 in). Following this, complete closure of the boot clamp using the ch 48894 - pliers. Before reinstallation, use the bench vise to extract the wheel drive shaft then guide the cv joint through four to five round movements for lubricant spreading before returning the shaft to the vehicle.