How to replace the LH Differential Cover and seal on 2006 Chevrolet Corvette?

To change the differential carrier cover and seal on the left, you have to first lift and support the vehicle, remove the lh rear tire and wheel assembly, remove the lh wheel drive shaft, and remove the lh Muffler assembly. Drain out the fluid from the differential and unfasten the damper or tuned absorber bolts in addition to the actual damper/tuned absorber. Loosen the nut that holds the transmission to the transmission lh mounting stud while also inserting another nut on the stud prior to removing the stud from the Differential Cover (left). Clean out the dirt or debris around the Differential Cover (left), then use a socket wrench to pull out the 2 bolts that holds the cover in place, then remove the Differential Cover (left) and dispose of the o-ring seal from the differential side cover. For installation clean up the o-ring sealing surface of the Differential Cover (left) and the differential housing then install a new o-ring seal to the Differential Cover (left) and provide it to the differential. Thread in the Differential Cover (left) retaining bolts and tighten to 25 nm (18 ft. Lbs.). Install the transmission mounting stud onto the Differential Cover using the two nuts on the stud, then tighten to 42 nm (31 ft. [b]) lbs. And remove the second nut (left) (left). Tighten nut holding the transmission to the transmission lh mounting stud to 50n m (37 ft. Lbs.). Then install damper/tuned absorber on the Differential Cover (left) then bolt down to a torque of 25 nm (18 ft. Lbs). Top up the differential with the correct fluids to the right level, and thereafter refit the lh Muffler assembly, the lh wheel drive shaft, and the lh rear tire and wheel assembly before lowering the vehicle.

OEM 2006 Chevrolet Corvette Differential Cover

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

8 Differential Covers found

View related parts
2006 Chevrolet Corvette Carrier Cover Part Number: 19259474
Product Specifications
- Other Name: Cover, Differential Carrier; Differential Cover; Cover, Differential(Ring Gear And Pinion)
- Replaces: 19181856, 19133199
- Item Weight: 5.80 Pounds
- Item Dimensions: 15.2 x 11.2 x 6.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19259474
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2006 Chevrolet Corvette Submodels:
- 427 Limited Edition Z06, Z06, Z06 Carbon, ZR1 | 8 Cyl 6.2 L GAS, 8 Cyl 7.0 L GAS
View related parts
2006 Chevrolet Corvette Carrier Cover Part Number: 89060173
Product Specifications
- Other Name: Cover; Differential Cover; Cover, Differential(Ring Gear And Pinion)
- Position: Passenger Side
- Item Weight: 5.80 Pounds
- Item Dimensions: 14.7 x 10.4 x 6.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 89060173
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2006 Chevrolet Corvette Submodels:
- Base, Grand Sport, ZR1 | 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L GAS
View related parts
2006 Chevrolet Corvette Carrier Cover Part Number: 89059221
Product Specifications
- Other Name: Cover; Differential Cover; Cover, Differential(Ring Gear And Pinion)
- Position: Passenger Side
- Replaces: 19133255, 89060174
- Item Weight: 7.40 Pounds
- Item Dimensions: 6.8 x 16.5 x 12.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 89059221
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2006 Chevrolet Corvette Submodels:
- Base, Grand Sport | 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L GAS
View related parts
2006 Chevrolet Corvette Carrier Cover Part Number: 19132920
Product Specifications
- Other Name: Cover; Differential Cover; Cover, Differential(Ring Gear And Pinion)
- Position: Rear Driver Side
- Item Weight: 6.60 Pounds
- Item Dimensions: 17.3 x 11.4 x 7.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19132920
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2006 Chevrolet Corvette Submodels:
- 427, 427 Limited Edition Z06, Z06, Z06 Carbon, ZR1 | 8 Cyl 6.2 L GAS, 8 Cyl 7.0 L GAS
View related parts
2006 Chevrolet Corvette Carrier Cover Part Number: 19132926
Product Specifications
- Other Name: Cover; Differential Cover; Cover, Differential(Ring Gear And Pinion)
- Position: Rear Driver Side
- Item Weight: 6.50 Pounds
- Item Dimensions: 15.2 x 10.1 x 5.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19132926
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2006 Chevrolet Corvette Submodels:
- 427, 427 Limited Edition Z06, Base, Grand Sport, Z06, Z06 Carbon, ZR1 | 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 7.0 L GAS
View related parts
2006 Chevrolet Corvette Carrier Cover Part Number: 19132931
Product Specifications
- Other Name: Cover; Differential Cover; Cover, Differential(Ring Gear And Pinion)
- Position: Rear Driver Side
- Item Weight: 5.80 Pounds
- Item Dimensions: 18.3 x 13.3 x 9.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19132931
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2006 Chevrolet Corvette Submodels:
- Base | 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L GAS
View related parts
2006 Chevrolet Corvette Carrier Cover Part Number: 19132930
Product Specifications
- Other Name: Cover; Differential Cover; Cover, Differential(Ring Gear And Pinion)
- Position: Rear Driver Side
- Item Weight: 5.60 Pounds
- Item Dimensions: 14.1 x 10.3 x 5.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 19132930
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2006 Chevrolet Corvette Submodels:
- Base | 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L GAS
View related parts
2006 Chevrolet Corvette Front Cover, Rear Part Number: 12458079
Product Specifications
- Other Name: Cover, Rear Axle Housing
- Position: Rear
- Item Weight: 0.70 Pounds
- Item Dimensions: 8.9 x 9.0 x 1.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 12458079
- Warranty: This genuine part is guaranteed by GM's factory warranty.
More Info
Fits the following 2006 Chevrolet Corvette Submodels:
- 427 Limited Edition Z06, 50th Anniversary Edition, 50th Anniversary Edition Pace Car, Base, Grand Sport, Indianapolis 500 Pace Car, Z06, ZR1 | 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L GAS, 8 Cyl 6.2 L GAS, 8 Cyl 7.0 L GAS

2006 Chevrolet Corvette Differential Cover

With a comprehensive array of OEM 2006 Chevrolet Corvette Differential Cover, from fuel pumps to door handles, our website is a one-stop-shop for your needs. All our genuine 2006 Chevrolet Corvette Differential Cover are backed by the manufacturer's warranty and are offered at competitive prices in the market. Rest assured, you can shop with complete confidence.

2006 Chevrolet Corvette Differential Cover Parts and Q&A

Q: How to replace the LH Differential Cover and seal on 2006 Chevrolet Corvette?
A: To change the differential carrier cover and seal on the left, you have to first lift and support the vehicle, remove the lh rear tire and wheel assembly, remove the lh wheel drive shaft, and remove the lh Muffler assembly. Drain out the fluid from the differential and unfasten the damper or tuned absorber bolts in addition to the actual damper/tuned absorber. Loosen the nut that holds the transmission to the transmission lh mounting stud while also inserting another nut on the stud prior to removing the stud from the Differential Cover (left). Clean out the dirt or debris around the Differential Cover (left), then use a socket wrench to pull out the 2 bolts that holds the cover in place, then remove the Differential Cover (left) and dispose of the o-ring seal from the differential side cover. For installation clean up the o-ring sealing surface of the Differential Cover (left) and the differential housing then install a new o-ring seal to the Differential Cover (left) and provide it to the differential. Thread in the Differential Cover (left) retaining bolts and tighten to 25 nm (18 ft. Lbs.). Install the transmission mounting stud onto the Differential Cover using the two nuts on the stud, then tighten to 42 nm (31 ft. [b]) lbs. And remove the second nut (left) (left). Tighten nut holding the transmission to the transmission lh mounting stud to 50n m (37 ft. Lbs.). Then install damper/tuned absorber on the Differential Cover (left) then bolt down to a torque of 25 nm (18 ft. Lbs). Top up the differential with the correct fluids to the right level, and thereafter refit the lh Muffler assembly, the lh wheel drive shaft, and the lh rear tire and wheel assembly before lowering the vehicle.