How to remove and reinstall the rear bumper on Pontiac Fiero?

Open the engine compartment lid and remove the six screw covers from the trailing edge of the rear panel. Next, take out the six taillight retaining screws from the rear panel and slide out each taillight lens far enough to access the bulb holders. Disconnect all four bulb holders from the backside of each taillight lens by pushing in the locking tabs and turning the bulb holders counterclockwise; for the inboard three bulb holders, push in the lock tab and rotate counterclockwise, while for the outboard bulb holder, rotate counterclockwise and pull it out. Carefully set the bulb holders aside. Remove the seven pop fasteners from the top of the rear bumper fascia, then take out the sidemarker retaining screws and disconnect the sidemarker bulb holder from each sidemarker, removing the sidemarker strips from both sides. Remove the screw attaching the rear bumper fascia to the rear panel from each sidemarker strip indent, followed by the four screws in each wheel well and the seven plastic push retainers from the underside of the rear bumper fascia. Pull the rear bumper fascia away from the vehicle far enough to disconnect the two license plate lamp bulb holders. If a new energy absorber is to be installed, pull out the pop fastener push retainers and remove the energy absorbing device; if unable to pull the retainers, drill them out as they must be replaced. Place a new energy absorbing device in position and install new push retainers. Position the rear bumper fascia, ensuring the two license plate light bulb holders are connected to the backside of the license plate well, then install the seven plastic push retainers in the underside of the fascia. Install the four screws that attach the fascia to each wheel well and tighten them securely, followed by the screw that attaches the side of the fascia to the rear panel at the sidemarker strip indent. Connect the bulb holder to the backside of each sidemarker, place the sidemarker in position over its indent, and install the two sidemarker mounting screws. Finally, install the seven pop fastener push retainers into the top of the fascia, connect the four bulb holders to each taillight lens, push the taillight lenses into place, install and tighten securely the taillight lens mounting screws, and install the taillight lens mounting screw plastic covers.

OEM Pontiac Bumper

Bumper Fascia

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

203 Bumpers found

View related parts
Pontiac Bumper Cover Part Number: 19151158
$202.29 MSRP: $302.44
You Save: $100.15 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Fascia, Front And Rear Bumper/Fascia Face
- Position: Front
- Replaces: 12335944, 19120467
Fits the following Pontiac Models:
- G6 | 2005-2009 | Base, GT, GTP | 4 Cyl 2.4 L GAS, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L GAS, 6 Cyl 3.9 L GAS
View related parts
Pontiac Bumper Cover Part Number: 22548235
$56.86 MSRP: $509.50
You Save: $452.64 (89%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Fascia, Front And Rear Bumper/Fascia Face
- Position: Rear
Fits the following Pontiac Models:
- Grand Am | 1992-1995 | GT | 4 Cyl 2.3 L GAS, 6 Cyl 3.1 L GAS
View related parts
Pontiac Bumper Cover, Front Part Number: 12336088
$634.38 MSRP: $952.71
You Save: $318.33 (34%)
ADD TO CART
Product Specifications
- Other Name: Fascia Assembly, Front Bumper (Primed); Fascia, Front And Rear Bumper/Fascia Face
- Position: Front
Fits the following Pontiac Models:
- Grand Prix | 2005-2008 | GXP | 8 Cyl 5.3 L GAS
View related parts
Pontiac Bumper Cover Part Number: 12336044
$169.17 MSRP: $252.92
You Save: $83.75 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Fascia, Front And Rear Bumper/Fascia Face
- Position: Rear
- Replaces: 12335519
Fits the following Pontiac Models:
- Bonneville | 2002-2005 | SE | 6 Cyl 3.8 L GAS
View related parts
Pontiac Bumper Cover Part Number: 95711879
$700.89 MSRP: $1052.59
You Save: $351.70 (34%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Fascia Assembly, Front Bumper *Paint To Match; Fascia, Front And Rear Bumper/Fascia Face
- Replaces: 92169488
Fits the following Pontiac Models:
- GTO | 2004-2006 | Base | 8 Cyl 5.7 L GAS, 8 Cyl 6.0 L GAS
View related parts
Pontiac Bumper Cover, Rear Upper Part Number: 19121114
$230.56 MSRP: $338.23
You Save: $107.67 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Fascia, Rear Bumper Upper *Primed; Fascia, Front And Rear Bumper/Fascia Face
- Position: Rear Upper
- Replaces: 12335945, 19120668, 89025117
Fits the following Pontiac Models:
- G6 | 2005-2009 | Base, GT, GTP | 4 Cyl 2.4 L GAS, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.6 L GAS, 6 Cyl 3.9 L GAS
View related parts
Pontiac Bumper Cover, Rear Part Number: 19120695
$128.00 MSRP: $213.38
You Save: $85.38 (41%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Fascia, Rear Bumper (Primed); Fascia, Front And Rear Bumper/Fascia Face
- Position: Rear
- Replaces: 89025122
Fits the following Pontiac Models:
- G5 | 2007-2009 | GT | 4 Cyl 2.2 L GAS, 4 Cyl 2.4 L GAS
View related parts
Pontiac Lower Panel Part Number: 10324182
Product Specifications
- Other Name: Fascia, Front And Rear Bumper/Fascia Face
- Position: Front Lower
Fits the following Pontiac Models:
- Grand Prix | 2004-2008 | Base, GT, GT1, GT2, GTP | 6 Cyl 3.8 L GAS
View related parts
Pontiac End Cover, Passenger Side Part Number: 12335072
Product Specifications
- Other Name: Fascia, Front And Rear Bumper/Fascia Face
- Position: Passenger Side
Fits the following Pontiac Models:
- Grand Prix | 1985-1987 | Base, Brougham, LE | 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS
View related parts
Pontiac End Cover, Driver Side Part Number: 12335073
Product Specifications
- Other Name: Fascia, Front And Rear Bumper/Fascia Face
- Position: Driver Side
Fits the following Pontiac Models:
- Grand Prix | 1985-1987 | Base, Brougham, LE | 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS
View related parts
Pontiac Cover Part Number: 12335074
Product Specifications
- Other Name: Fascia, Front And Rear Bumper/Fascia Face
- Position: Rear
Fits the following Pontiac Models:
- Grand Prix | 1985-1987 | Base, Brougham, LE | 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L GAS, 8 Cyl 5.0 L GAS
View related parts
Pontiac Bumper Cover, Front Part Number: 10252349
Product Specifications
- Other Name: Fascia-Front Bumper; Fascia, Front And Rear Bumper/Fascia Face
- Position: Front
Fits the following Pontiac Models:
- Grand Prix | 1992-1996 | Base, GT, LE, SE, STE | 6 Cyl 3.1 L GAS, 6 Cyl 3.4 L GAS
View related parts
Pontiac Bumper Cover, Front Part Number: 14088034
Product Specifications
- Other Name: Fascia-Front Bumper; Fascia, Front And Rear Bumper/Fascia Face
- Position: Front
Fits the following Pontiac Models:
- Grand Prix | 1988-1990 | LE, SE | 4 Cyl 2.3 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 3.1 L GAS
View related parts
Pontiac Bumper Cover, Front Part Number: 10252361
Product Specifications
- Other Name: Fascia-Front Bumper; Fascia, Front And Rear Bumper/Fascia Face
- Position: Front
Fits the following Pontiac Models:
- Grand Prix | 1991-1996 | SE | 4 Cyl 2.3 L GAS, 6 Cyl 3.1 L GAS, 6 Cyl 3.4 L GAS
View related parts
Pontiac Bumper Cover Part Number: 88893301
Product Specifications
- Other Name: Fascia, Front And Rear Bumper/Fascia Face
- Position: Front
Fits the following Pontiac Models:
- Grand Prix | 1997-1999 | GT, GTP, SE | 6 Cyl 3.1 L GAS, 6 Cyl 3.8 L GAS
View related parts
Pontiac Bumper Cover Part Number: 12482891
Product Specifications
- Other Name: Fascia, Front And Rear Bumper/Fascia Face
- Position: Rear
Fits the following Pontiac Models:
- Bonneville | 2000-2001 | SE | 6 Cyl 3.8 L GAS
View related parts
Pontiac Bumper Cover Part Number: 12335861
Product Specifications
- Other Name: Fascia, Front And Rear Bumper/Fascia Face
- Position: Front
- Replaces: 12335518
Fits the following Pontiac Models:
- Bonneville | 2002-2005 | SE | 6 Cyl 3.8 L GAS
View related parts
Pontiac Bumper Cover Part Number: 25527632
Product Specifications
- Other Name: Fascia, Front And Rear Bumper/Fascia Face
- Position: Rear
Fits the following Pontiac Models:
- Bonneville | 1988-1991 | SSE | 6 Cyl 3.8 L GAS
View related parts
Pontiac Bumper Cover Part Number: 12336410
Product Specifications
- Other Name: Fascia, Front And Rear Bumper/Fascia Face
- Position: Front
Fits the following Pontiac Models:
- Bonneville | 1988-1991 | SSE | 6 Cyl 3.8 L GAS
View related parts
Pontiac Bumper Cover, Front Part Number: 25961375
$305.42 MSRP: $456.62
You Save: $151.20 (34%)
Product Specifications
- Other Name: Fascia Assembly-Front Bumper *Service Primer; Fascia, Front And Rear Bumper/Fascia Face
- Position: Front
Fits the following Pontiac Models:
- G6 | 2009-2010 | Base, GT | 4 Cyl 2.4 L FLEX, 4 Cyl 2.4 L GAS, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS

| Page 1 of 11 |Next >

1-20 of 203 Results

Pontiac Bumper

Choose OEM Bumper, you're making the optimal decision for superior quality and perfect performance. You can feel confident because each component goes through stringent quality checks. Every part is carefully built to comply with Pontiac's factory specifications. You'll enjoy a smooth, worry-free installation that fits just right. At ChevyPartsDeal.com, you'll find it easy to get top-quality OEM Pontiac Bumper. You can shop at highly competitive prices and protect your budget. All our genuine Pontiac parts include a dependable manufacturer's warranty. You'll also appreciate our straightforward return policy and swift delivery services for extra convenience.

Pontiac Bumper cushions the tiny cracks and crashes in the roads and leaves the paint intact and the metals in a straight line. Pontiac created a bit of rough image by combining large horse with agile maneuverability and an outlaw image, hustling down the pave where other timid vehicles had sneaked and offering young gearheads a cheap taste of bragging right off the factory floor. The broad-track appearance with the tires planted at the corners, the aggressive scoops, stripes, boisterous exhaust sounds told drivers they were confident and it could be felt through the beat of rock playing out of the dash. The cockpit went round the driver, instruments gleaming and clear, pedals on hand to fling that throttle on a spur-of-the-moment, and the steering to nip into traffic gridlock, and then lock on blasts down the highway, without breaking your wallet or your back. Pontiac is innovating Bumper technology on the basis of alloy bars that combine with carbon steel and stainless skins to shave off weight but increase strength, shrugging off rust but remaining slim enough to keep curb mass under control. Pontiac complements this Bumper with energy-absorbing brackets that squeeze down on the cost of repairs following supermarket dings and low-speed fender-taps, yet satisfy federal impact criteria without taking away the aggressive profile of the car. Every Bumper is mounted across the line, and at first glance the owners of classics and later models alike have the confidence of plug-and-play and the same stout shield at any cruise night.

Pontiac Bumper Parts and Q&A

Cover
10042563
Q: How to remove and reinstall the rear bumper on Pontiac Fiero?
A:
Open the engine compartment lid and remove the six screw covers from the trailing edge of the rear panel. Next, take out the six taillight retaining screws from the rear panel and slide out each taillight lens far enough to access the bulb holders. Disconnect all four bulb holders from the backside of each taillight lens by pushing in the locking tabs and turning the bulb holders counterclockwise; for the inboard three bulb holders, push in the lock tab and rotate counterclockwise, while for the outboard bulb holder, rotate counterclockwise and pull it out. Carefully set the bulb holders aside. Remove the seven pop fasteners from the top of the rear bumper fascia, then take out the sidemarker retaining screws and disconnect the sidemarker bulb holder from each sidemarker, removing the sidemarker strips from both sides. Remove the screw attaching the rear bumper fascia to the rear panel from each sidemarker strip indent, followed by the four screws in each wheel well and the seven plastic push retainers from the underside of the rear bumper fascia. Pull the rear bumper fascia away from the vehicle far enough to disconnect the two license plate lamp bulb holders. If a new energy absorber is to be installed, pull out the pop fastener push retainers and remove the energy absorbing device; if unable to pull the retainers, drill them out as they must be replaced. Place a new energy absorbing device in position and install new push retainers. Position the rear bumper fascia, ensuring the two license plate light bulb holders are connected to the backside of the license plate well, then install the seven plastic push retainers in the underside of the fascia. Install the four screws that attach the fascia to each wheel well and tighten them securely, followed by the screw that attaches the side of the fascia to the rear panel at the sidemarker strip indent. Connect the bulb holder to the backside of each sidemarker, place the sidemarker in position over its indent, and install the two sidemarker mounting screws. Finally, install the seven pop fastener push retainers into the top of the fascia, connect the four bulb holders to each taillight lens, push the taillight lenses into place, install and tighten securely the taillight lens mounting screws, and install the taillight lens mounting screw plastic covers.