How to remove and install a water pump on Oldsmobile Cutlass?

Disconnect the negative battery cable. Drain the radiator. Reaching inside the radiator shroud, remove the bolts which secure the fan to the water pump hub. Remove the fan and spacer(if equipped). A thermostatic fan clutch must remain in the "in car"osition. If equipped with a two-piece radiator shroud, remove the upper half of the shroud for better access to the water pump. It is now necessary to loosen and remove all drivebelts from the water pump pulley. The number of belts will depend upon model, year.and equipment Loosen the adjusting and pivot bolts of each affected component (air pump, alternator, air conditioning compressor) and push the component inward to loosen the belt enough to be removed from the water pump pulley. Disconnect and remove all mounting brackets which are attached to the water pump. These may include on late model vehicles the alternator, air conditioning compressor, and power steering brackets. Disconnect the lower radiator hose, heater hose, and bypass hose at the water pump. Remove the remaining bolts which secure the water pump to the front cover of the engine. Lift the water pump housing straight out of the front cover and then away from the engine. If installing a new or rebuilt water pump, transfer all fittings and studs to the new water pump (If a replacement pump is used, transfer all hose fittings from the old pump to the new). Clean the gasket surfaces of the front cover completely using a gasket scraper or putty knife. Use a thin coat of gasket sealant on the new gaskets and install the new water pump. Place the pump into position on the front cover and secure loosely with the bolts. Do not torque-tighten these bolts until all brackets have been installed to their original position on the water pump. Tighten all water pump bolts to torque specifications. Install the engine components in the reverse order or removal,tightening the appropriate fasteners to torque specifications. Adjust all drivebelts to the proper tension. Connect the negative battery cable and fill the radiator with a mixture of ethylene glycol antifreeze and water in a 50/50 mixture. Start the engine and allow to idle until the upper radiator hose gets hot. Check for leaks. With engine hot, fill with more coolant mixture until the level is at the bottom of the filler neck. Install radiator cap and check coolant level periodically over the next few miles of driving.

OEM Oldsmobile Water Pump

H2O Pump

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

26 Water Pumps found

View related parts
Oldsmobile Water Pump Part Number: 19210509
$85.62 MSRP: $166.18
You Save: $80.56 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Kit, Water; Water Pump Assembly; Pump Kit, Engine Coolant
- Replaces: 12487361, 88894344, 07490007, 12529993, 12365639, 7490007, 89017900, 89017467
Fits the following Oldsmobile Models:
- Aurora | 2001-2003, 1995-1999 | Base | 8 Cyl 4.0 L GAS
View related parts
Oldsmobile Water Pump, Green Line Part Number: 12630084
$203.28 MSRP: $394.54
You Save: $191.26 (49%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Water Pump Assembly; Pump, Engine Coolant
- Replaces: 12585226, 12591894, 12624936, 19181920, 24467301, 24439798
Fits the following Oldsmobile Models:
- Alero | 2002-2004 | GL, GLS, GX | 4 Cyl 2.2 L GAS
View related parts
Oldsmobile Water Pump Part Number: 19209288
$130.58 MSRP: $255.64
You Save: $125.06 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Kit, Water; Fan Blade; Water Pump Assembly; Pump Kit, Engine Coolant
- Replaces: 89017813, 89060462, 12482903, 12537829, 89018214
Fits the following Oldsmobile Models:
- 88 | 1996-1999 | 50th Anniversary Edition, Royale, Royale LS | 6 Cyl 3.8 L GAS
- 98 | 1996 | Regency Elite | 6 Cyl 3.8 L GAS
- Intrigue | 1998-1999 | Base, GL, GLS, GX | 6 Cyl 3.8 L GAS
- LSS | 1996-1999 | Base | 6 Cyl 3.8 L GAS
- Regency | 1997-1998 | Base | 6 Cyl 3.8 L GAS
View More
View related parts
Oldsmobile Water Pump Part Number: 89017269
$131.73 MSRP: $257.90
You Save: $126.17 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Kit, Water; Water Pump Assembly; Pump Kit, Engine Coolant
Fits the following Oldsmobile Models:
- Alero | 1999-2004 | GL, GLS, GX | 6 Cyl 3.4 L GAS
- Cutlass | 1997-1999 | Base, GL, GLS | 6 Cyl 3.1 L GAS
- Cutlass Supreme | 1997 | Base | 6 Cyl 3.1 L GAS
View More
View related parts
Oldsmobile Water Pump Part Number: 89060527
$232.95 MSRP: $456.07
You Save: $223.12 (49%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Kit, Water; Water Pump Assembly; Pump Kit, Engine Coolant
- Replaces: 12528917, 89017748, 12532528
Fits the following Oldsmobile Models:
- Bravada | 1996-2004 | Base | 6 Cyl 4.2 L GAS, 6 Cyl 4.3 L GAS
View related parts
Oldsmobile Water Pump Part Number: 12482919
$73.63 MSRP: $133.27
You Save: $59.64 (45%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Kit, Water; Water Pump Assembly; Pump Kit, Engine Coolant
- Replaces: 12537417, 12537135
Fits the following Oldsmobile Models:
- 88 | 1992-1995 | Royale, Royale LS, Royale LSS | 6 Cyl 3.8 L GAS
- 98 | 1991-1995 | Regency, Regency Elite, Touring | 6 Cyl 3.8 L GAS
- Achieva | 1992-1993 | S, SC, SL | 6 Cyl 3.3 L GAS
- Cutlass Ciera | 1991-1993 | Base, S, SL | 6 Cyl 3.3 L GAS
- Cutlass Cruiser | 1991-1993 | Base, S, SL | 6 Cyl 3.3 L GAS
- Delta 88 | 1991 | Royale, Royale Brougham | 6 Cyl 3.8 L GAS
- Silhouette | 1992-1995 | Base | 6 Cyl 3.8 L GAS
- Toronado | 1991-1992 | Base, Trofeo | 6 Cyl 3.8 L GAS
View More
View related parts
Oldsmobile Water Pump Part Number: 12508606
$18.48 MSRP: $129.37
You Save: $110.89 (86%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Kit, Water; Water Pump Assembly; Pump Kit, Engine Coolant; Pump, Engine Coolant
Fits the following Oldsmobile Models:
- Firenza | 1984-1988 | Base, Brougham LX, Brougham SX, Cruiser, Cruiser LX, Cruiser SX, ES, GT, LC, LX, S | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS
View related parts
Oldsmobile Water Pump Part Number: 12458922
Product Specifications
- Other Name: Pump Kit, Water; Water Pump Assembly; Pump Kit, Engine Coolant
- Replaces: 10174846, 12522034
Fits the following Oldsmobile Models:
- Custom Cruiser | 1991-1992 | Base | 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS
View related parts
Oldsmobile Water Pump Part Number: 19168613
Product Specifications
- Other Name: Pump Kit, Water; Pump Kit, Engine Coolant
- Replaces: 12458115, 12455105
Fits the following Oldsmobile Models:
- Aurora | 2001-2002 | Base | 6 Cyl 3.5 L GAS
- Intrigue | 1999-2002 | GL, GLS, GX | 6 Cyl 3.5 L GAS
View related parts
Oldsmobile Water Pump Part Number: 12620226
$145.44 MSRP: $260.88
You Save: $115.44 (45%)
Product Specifications
- Other Name: Pump, Water; Pump, Engine Coolant
- Replaces: 24576952
Fits the following Oldsmobile Models:
- Bravada | 2002-2004 | Base | 6 Cyl 4.2 L GAS
View related parts
Oldsmobile Water Pump Part Number: 24577255
Product Specifications
- Other Name: Pump; Drive Plate; Water Pump Assembly
- Replaces: 24575951, 24576875, 24573636
Fits the following Oldsmobile Models:
- Achieva | 1996-1998 | S, SC, SL | 4 Cyl 2.4 L GAS
- Alero | 1999-2001 | GL, GLS, GX | 4 Cyl 2.4 L GAS
View related parts
Oldsmobile Water Pump Part Number: 231886
Product Specifications
- Other Name: Pump Package-Water (All Non A/C) (Asbestos); Pump Assembly; Water Pump Assembly; Pump
Fits the following Oldsmobile Models:
- 98 | 1984 | Regency, Regency Brougham | 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL
- Custom Cruiser | 1984-1987 | Base | 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL
- Cutlass Salon | 1985 | 442, Base | 6 Cyl 3.8 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL
- Cutlass Supreme | 1984-1985 | Base, Brougham, LS | 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L DIESEL, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL
- Delta 88 | 1984-1985 | Royale, Royale Brougham, Royale Brougham LS | 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL
- Toronado | 1984-1985 | Brougham, Caliente | 6 Cyl 4.1 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL
View More
View related parts
Oldsmobile Water Pump Part Number: 25527536
Product Specifications
- Other Name: Pump Kit, Water; Pump Assembly; Water Pump Assembly; Pump; Pump, Engine Coolant
Fits the following Oldsmobile Models:
- Cutlass Calais | 1988, 1984 | Base, GT, Hurst, SL | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L DIESEL, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL
- Cutlass Cruiser | 1987-1988 | Brougham, Brougham LS, LS, SL | 6 Cyl 3.8 L GAS
- Cutlass Salon | 1985-1987 | 442, Base | 6 Cyl 3.8 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL
- Cutlass Supreme | 1984-1988 | 442, Base, Brougham, Classic, Classic Brougham, LS | 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L DIESEL, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL
- Delta 88 | 1984-1985 | Royale, Royale Brougham, Royale Brougham LS | 6 Cyl 3.8 L GAS
- Toronado | 1984-1985 | Brougham, Caliente | 6 Cyl 4.1 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL
View More
View related parts
Oldsmobile Water Pump Part Number: 12482696
Product Specifications
- Other Name: Pump Kit, Water; Pump Assembly; Water Pump Assembly; Pump; Pump Kit, Engine Coolant; Pump, Engine Coolant
- Replaces: 10174860
Fits the following Oldsmobile Models:
- Cutlass Ciera | 1986 | Brougham, ES, GT, Holiday, LS, S, SL | 6 Cyl 2.8 L GAS
- Omega | 1984 | Base, Brougham | 6 Cyl 2.8 L GAS
View related parts
Oldsmobile Water Pump Part Number: 10181369
Product Specifications
- Other Name: Pump Kit-Water
- Replaced by: 12482000
Fits the following Oldsmobile Models:
- Cutlass Ciera | 1991 | Base, S | 4 Cyl 2.5 L GAS
- Cutlass Cruiser | 1991 | S | 4 Cyl 2.5 L GAS
View related parts
Oldsmobile Water Pump Part Number: 12482000
Product Specifications
- Other Name: Pump Kit, Water; Water Pump Assembly; Pump Kit, Engine Coolant; Body, Engine Coolant; Pump, Engine Coolant
- Replaces: 10181369, 12360447
Fits the following Oldsmobile Models:
- Cutlass Ciera | 1987-1992 | Base, Brougham, GT, LS, S, SL | 4 Cyl 2.5 L GAS
- Cutlass Cruiser | 1987-1992 | Base, Brougham, Brougham LS, LS, S, SL | 4 Cyl 2.5 L GAS
View related parts
Oldsmobile Water Pump Part Number: 12337519
Product Specifications
- Other Name: Pump; Water Pump Assembly; Pump Kit, Engine Coolant; Pump, Engine Coolant
Fits the following Oldsmobile Models:
- 98 | 1984 | Regency, Regency Brougham | 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL
- Custom Cruiser | 1984-1990 | Base | 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL
- Cutlass Calais | 1988, 1984 | Base, GT, Hurst, SL | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L DIESEL, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL
- Cutlass Cruiser | 1987-1988 | Brougham, Brougham LS, LS, SL | 6 Cyl 3.8 L GAS
- Cutlass Salon | 1985-1987 | 442, Base | 6 Cyl 3.8 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL
- Cutlass Supreme | 1984-1988 | 442, Base, Brougham, Classic, Classic Brougham, LS | 6 Cyl 3.8 L GAS, 6 Cyl 4.3 L DIESEL, 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL
- Delta 88 | 1984-1985 | Royale, Royale Brougham, Royale Brougham LS | 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL
- Toronado | 1984-1985 | Brougham, Caliente | 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L DIESEL
View More
View related parts
Oldsmobile Water Pump Part Number: 10174979
Product Specifications
- Other Name: Pump Kit, Water; Pump; Pump Kit, Engine Coolant; Pump, Engine Coolant
Fits the following Oldsmobile Models:
- Firenza | 1985-1986 | Base, Brougham LX, Brougham SX, Cruiser LX, Cruiser SX, ES, GT | 6 Cyl 2.8 L GAS
View related parts
Oldsmobile Water Pump Part Number: 10065240
Product Specifications
- Other Name: Pump Kit, Water; Pump; Pump Kit, Engine Coolant
Fits the following Oldsmobile Models:
- Firenza | 1984-1988 | Base, Brougham LX, Brougham SX, Cruiser, Cruiser LX, Cruiser SX, ES, GT, LC, LX, S, SX | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS, 6 Cyl 2.8 L GAS
View related parts
Oldsmobile Water Pump Assembly Part Number: 12355499
Product Specifications
- Other Name: Pump Kit, Water; Water Pump; Pump Kit, Engine Coolant; Pump, Engine Coolant
Fits the following Oldsmobile Models:
- 98 | 1985 | Regency, Regency Brougham | 6 Cyl 4.3 L DIESEL
- Cutlass Ciera | 1984-1985 | Brougham, Cruiser LS, LS | 6 Cyl 4.3 L DIESEL

| Page 1 of 2 |Next >

1-20 of 26 Results

Oldsmobile Water Pump

Choose OEM Water Pump, you're making the optimal decision for superior quality and perfect performance. You can feel confident because each component goes through stringent quality checks. Every part is carefully built to comply with Oldsmobile's factory specifications. You'll enjoy a smooth, worry-free installation that fits just right. At ChevyPartsDeal.com, you'll find it easy to get top-quality OEM Oldsmobile Water Pump. You can shop at highly competitive prices and protect your budget. All our genuine Oldsmobile parts include a dependable manufacturer's warranty. You'll also appreciate our straightforward return policy and swift delivery services for extra convenience.

Oldsmobile Water Pump maintains the flow of coolant at high speed to ensure engines are cool and performance is consistent. Oldsmobile expanded a 1897 start up to a large name in Detroit by challenging established motorist technologies by pushing things to the edge, like the Curved Dash that has democratized motoring to the Hydra-Matic transmission that has rendered the clutch pedal unnecessary and has allowed families to afford to commute to work and school without sacrificing their budgets. Oldsmobile pursued smoother rides and more robust engines, and refused to make reliability a bonus option and made it part of the steel and glass to ensure that owners could count on the badge in road and severe winters alike through thick and thin all the years without it becoming a spectacle. Oldsmobile was not idle, as every new idea had to prove its worth by reducing noise, reducing vibration, and just letting car owners enjoy their leisure instead of fighting their way to work on a basis every day. The coolant must be vigorously pumped through the block on its exit side of the radiator and the Water Pump has the duty of capturing that liquid and pushing it to all of the hot cylinder walls, sweeping the heat away before the metal grows too hot and then pumping the fluid back into the radiator to proceed through another chill cycle an operation repeated thousands of times during a ride, a process that prevents the needles of the temperature gauges even on a hard pull or in the summer jammer. The Water Pump can be installed on the old cruiser and new upgrades, as it spins by use of belts or the new electric motors. The Water Pump is essential for maintaining optimal engine temperature.

Oldsmobile Water Pump Parts and Q&A

Water Pump
89017269
Q: How to remove and install a water pump on Oldsmobile Cutlass?
A:
Disconnect the negative battery cable. Drain the radiator. Reaching inside the radiator shroud, remove the bolts which secure the fan to the water pump hub. Remove the fan and spacer(if equipped). A thermostatic fan clutch must remain in the "in car"osition. If equipped with a two-piece radiator shroud, remove the upper half of the shroud for better access to the water pump. It is now necessary to loosen and remove all drivebelts from the water pump pulley. The number of belts will depend upon model, year.and equipment Loosen the adjusting and pivot bolts of each affected component (air pump, alternator, air conditioning compressor) and push the component inward to loosen the belt enough to be removed from the water pump pulley. Disconnect and remove all mounting brackets which are attached to the water pump. These may include on late model vehicles the alternator, air conditioning compressor, and power steering brackets. Disconnect the lower radiator hose, heater hose, and bypass hose at the water pump. Remove the remaining bolts which secure the water pump to the front cover of the engine. Lift the water pump housing straight out of the front cover and then away from the engine. If installing a new or rebuilt water pump, transfer all fittings and studs to the new water pump (If a replacement pump is used, transfer all hose fittings from the old pump to the new). Clean the gasket surfaces of the front cover completely using a gasket scraper or putty knife. Use a thin coat of gasket sealant on the new gaskets and install the new water pump. Place the pump into position on the front cover and secure loosely with the bolts. Do not torque-tighten these bolts until all brackets have been installed to their original position on the water pump. Tighten all water pump bolts to torque specifications. Install the engine components in the reverse order or removal,tightening the appropriate fasteners to torque specifications. Adjust all drivebelts to the proper tension. Connect the negative battery cable and fill the radiator with a mixture of ethylene glycol antifreeze and water in a 50/50 mixture. Start the engine and allow to idle until the upper radiator hose gets hot. Check for leaks. With engine hot, fill with more coolant mixture until the level is at the bottom of the filler neck. Install radiator cap and check coolant level periodically over the next few miles of driving.