How to Replace the Front Axle Shaft Assembly in an A4WD on GMC Jimmy?

Start by raising the vehicle before beginning work on the front Axle Shaft (A4WD) inner shaft or housing replacement. The right side wheel drive shaft removal should be followed by disconnecting the inner Axle Shaft from the differential case side gear. First remove all bolts, nuts, and washers that secure the inner Axle Shaft housing then proceed with the inner Axle Shaft housing to differential carrier assembly bolts. Remove the integrated Axle Shaft and housing section from the differential carrier assembly followed by removing the inner Axle Shaft from its housing. You need to remove both the axle housing bearing and inner axle seal during this procedure. Start by putting the new bearing and seal onto the axle housing space before placing the inner Axle Shaft into its housing. Sealant material gm p/n 1052942 or equivalent must be applied to the inner axle housing differential carrier sealing surface before the inner Axle Shaft housing gets installed into the differential carrier assembly. Begin by installing the inner Axle Shaft housing bolts which you should tighten only by hand. Fasten the inner Axle Shaft housing onto the frame bracket through its bolts and washers and nuts while torquing inner Axle Shaft housing to frame bracket nuts at 98 nm (72 ft. Lbs.) and inner Axle Shaft housing to differential carrier assembly bolts at 48 nm (36 ft. Lbs.) reinstall the right side wheel drive shaft before examining the axle lubricant level and adding fluid if needed and lowering the vehicle.

How to service and repair the rear drive axle shaft on GMC Jimmy?

The repair process for the rear Axle Shaft begins with supporting the vehicle while it is raised before technicians can remove brake drums followed by rotating tires then braking rotors (if present). After removing the axle housing cover proceed with removing both the pinion shaft lock bolt along with the pinion shaft itself. Push the Axle Shaft toward the vehicle's center after detaching the c-lock from the button end while marking it for left or right use. Before installation, apply axle lubricant to the Axle Shaft wheel bearing surface and oil seal surface of the appropriate side while verifying the correct Axle Shaft and avoiding damage to the oil seal. Announce the splined end of the rear axle side gear into the housing, then push the Axle Shaft forward. Seating the c-lock onto the Axle Shaft demands outward pulling until it reaches the counterbore location of the rear axle side gear. After installing the differential pinion shaft through case and pinion apply loctite09 242 to the thread of the differential pinion shaft locking screw for preventing screw loosening before reinstalling. Position the pinion shaft hole against the lock bolt opening before installing a new locking bolt and tightening it to 36 nm (27 ft. Lbs.). Before installation place a gasket on the axle housing cover and fill the opening with axle lubricant up to 3/8 inches above the fill plug opening mark. Replace rear brake drums and rotors if present followed by tires and wheels installation. Afterward lower the vehicle and perform a test drive to verify there are no leaks.

OEM GMC Jimmy Axle Shaft

Car Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

43 Axle Shafts found

View related parts
GMC Jimmy Axle Shaft, Rear Part Number: 14039547
$245.55 MSRP: $432.42
You Save: $186.87 (44%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft, Rear Axle Drive
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1987 GMC Jimmy | Base, High Sierra, Sierra Classic | 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL
View related parts
GMC Jimmy Axle Shaft, Rear Part Number: 26050549
Product Specifications
- Other Name: Shaft, Rear Axle Drive; Axle Shafts
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-2001 GMC Jimmy | Base, Diamond Edition, Envoy, SL, SLE, SLS, SLT | 6 Cyl 4.3 L GAS
View related parts
GMC Jimmy Axle Shaft, Rear Part Number: 26009534
$286.49 MSRP: $450.77
You Save: $164.28 (37%)
Product Specifications
- Other Name: Shaft, Rear Axle Drive; Axle Shafts
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1999 GMC Jimmy | Base, Envoy, SL, SLE, SLS, SLT | 6 Cyl 4.3 L GAS
View related parts
GMC Jimmy Axle Shaft, Rear Part Number: 26033365
Product Specifications
- Other Name: Shaft, R/A; Axle Shafts; Shaft, Rear Axle Drive
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1997 GMC Jimmy | Base, SL, SLE, SLS, SLT | 6 Cyl 4.3 L GAS
View related parts
GMC Jimmy Axle Shaft, Rear Part Number: 26027706
Product Specifications
- Other Name: Shaft, Rear Axle; Axle Shafts; Shaft, Rear Axle Drive
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1994-1999 GMC Jimmy | Base, Envoy, SL, SLE, SLS, SLT | 6 Cyl 4.3 L GAS
View related parts
GMC Jimmy Axle Shafts Part Number: 7844114
Product Specifications
- Other Name: Shaft - Axle; Axle Shaft; Outer Joint Assembly; Shaft; Shaft, Front Axle
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1997 GMC Jimmy | Base, SL, SLE, SLS, SLT | 6 Cyl 4.3 L GAS
View related parts
GMC Jimmy Axle Shaft Part Number: 14071750
Product Specifications
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1991 GMC Jimmy | Base, High Sierra, Sierra Classic | 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL
View related parts
GMC Jimmy Axle Shaft, Driver Side Part Number: 26015323
Product Specifications
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1990-1991 GMC Jimmy | Base, Sierra Classic | 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL
View related parts
GMC Jimmy Axle Shaft, Front Part Number: 15521884
Product Specifications
- Other Name: Shaft, Front Wheel Drive; Axle Shafts; Shaft, Front Axle
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1991 GMC Jimmy | Base, High Sierra, Sierra Classic | 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL
View related parts
GMC Jimmy Stub Shaft, Front Part Number: 26034184
Product Specifications
- Other Name: Shaft Kit, Front Axle
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1999 GMC Jimmy | Base, Envoy, SL, SLE, SLS, SLT | 6 Cyl 4.3 L GAS
View related parts
GMC Jimmy Axle Shaft, Inner Passenger Side Part Number: 458878
Product Specifications
- Other Name: Shaft-Front Axle Inner (Right-Hand); Axle Shafts; Shaft, Front Axle
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1989 GMC Jimmy | Base, High Sierra, Sierra Classic | 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL
View related parts
GMC Jimmy Axle Shaft, Rear Part Number: 26033364
Product Specifications
- Other Name: Shaft, Rear Axle Drive
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-1997 GMC Jimmy | Base, SL, SLE, SLS, SLT | 6 Cyl 4.3 L GAS
View related parts
GMC Jimmy Axle Shafts, Rear Part Number: 26058925
Product Specifications
- Other Name: Shaft, Rear Axle Drive; Axle Shaft
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2000-2001 GMC Jimmy | Diamond Edition, Envoy, SL, SLE, SLS, SLT | 6 Cyl 4.3 L GAS
View related parts
GMC Jimmy Axle Shafts, Front Part Number: 26013559
Product Specifications
- Other Name: Shaft, Front Axle
- Position: Front
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1994 GMC Jimmy | Base, SLE, SLS, SLT | 6 Cyl 4.3 L GAS
View related parts
GMC Jimmy Axle Shaft, Inner Driver Side Part Number: 458877
Product Specifications
- Other Name: Shaft-Front Axle Inner (Left-Hand); Axle Shafts; Shaft, Front Axle
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984-1989 GMC Jimmy | Base, High Sierra, Sierra Classic | 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL
View related parts
GMC Jimmy Axle Shaft, Rear Part Number: 14030355
Product Specifications
- Other Name: Shaft, Rear Axle Drive; Axle Shafts
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-1993 GMC Jimmy | Base, SLE, SLS, SLT | 6 Cyl 4.3 L GAS
View related parts
GMC Jimmy Axle Shaft, Front Passenger Side Part Number: 26034185
Product Specifications
- Other Name: Shaft Kit, Front Axle; Axle Shafts; Output Shaft; Inner Joint Assembly
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1992-2001 GMC Jimmy | Base, Diamond Edition, Envoy, SL, SLE, SLS, SLT | 6 Cyl 4.3 L GAS
View related parts
GMC Jimmy Axle Shaft, Front Driver Side Part Number: 26053318
Product Specifications
- Other Name: Shaft, Front Axle; Axle Shafts; Shaft
- Position: Driver Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-2001 GMC Jimmy | Base, Diamond Edition, Envoy, SL, SLE, SLS, SLT | 6 Cyl 4.3 L GAS
View related parts
GMC Jimmy Axle Shaft, Front Passenger Side Part Number: 26053319
Product Specifications
- Other Name: Shaft, Front Axle; Axle Shafts
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1995-2001 GMC Jimmy | Base, Diamond Edition, Envoy, SL, SLE, SLS, SLT | 6 Cyl 4.3 L GAS
View related parts
GMC Jimmy Axle Shaft Part Number: 14071751
Product Specifications
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 1984 GMC Jimmy | Base | 8 Cyl 5.0 L GAS, 8 Cyl 5.7 L GAS, 8 Cyl 6.2 L DIESEL

| Page 1 of 3 |Next >

1-20 of 43 Results

GMC Jimmy Axle Shaft

Want to cut long-term maintenance and repair costs? Choose OEM Axle Shaft. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine GMC Jimmy parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM GMC Jimmy Axle Shaft includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

Axle Shaft, in GMC Jimmy automobiles, is a system that transmits power from the differential to wheels, enabling the ability of rotating each wheel independently in as related to the other for better grip. These pintle shafts are used in pairs and participate in bearing the weight of the vehicle, in transmitting torque force, in ensuring the position of the wheels. There is the live axle for transmittal of torque, and the non-driving axle for suspension, of which they come in different possibilities to fit the requirements of the vehicle. Through-form loads, bearings and seals of axle shafts are liable to deterioration, for which bearing and seal replacement becomes necessary; worn parts generate noise, vibration, and lubricant loss. In summary, the Axle Shaft is critical to the proper running and efficiency of GMC Jimmy cars.

GMC Jimmy Axle Shaft Parts and Q&A

Axle Shaft, Front
26042726
Q: How to Replace the Front Axle Shaft Assembly in an A4WD on GMC Jimmy?
A:
Start by raising the vehicle before beginning work on the front Axle Shaft (A4WD) inner shaft or housing replacement. The right side wheel drive shaft removal should be followed by disconnecting the inner Axle Shaft from the differential case side gear. First remove all bolts, nuts, and washers that secure the inner Axle Shaft housing then proceed with the inner Axle Shaft housing to differential carrier assembly bolts. Remove the integrated Axle Shaft and housing section from the differential carrier assembly followed by removing the inner Axle Shaft from its housing. You need to remove both the axle housing bearing and inner axle seal during this procedure. Start by putting the new bearing and seal onto the axle housing space before placing the inner Axle Shaft into its housing. Sealant material gm p/n 1052942 or equivalent must be applied to the inner axle housing differential carrier sealing surface before the inner Axle Shaft housing gets installed into the differential carrier assembly. Begin by installing the inner Axle Shaft housing bolts which you should tighten only by hand. Fasten the inner Axle Shaft housing onto the frame bracket through its bolts and washers and nuts while torquing inner Axle Shaft housing to frame bracket nuts at 98 nm (72 ft. Lbs.) and inner Axle Shaft housing to differential carrier assembly bolts at 48 nm (36 ft. Lbs.) reinstall the right side wheel drive shaft before examining the axle lubricant level and adding fluid if needed and lowering the vehicle.
Axle Shaft, Rear
26050549
Q: How to service and repair the rear drive axle shaft on GMC Jimmy?
A:
The repair process for the rear Axle Shaft begins with supporting the vehicle while it is raised before technicians can remove Brake Drums followed by rotating tires then braking rotors (if present). After removing the axle housing cover proceed with removing both the pinion shaft lock bolt along with the pinion shaft itself. Push the Axle Shaft toward the vehicle's center after detaching the c-lock from the button end while marking it for left or right use. Before installation, apply axle lubricant to the Axle Shaft wheel bearing surface and oil seal surface of the appropriate side while verifying the correct Axle Shaft and avoiding damage to the oil seal. Announce the splined end of the rear axle side gear into the housing, then push the Axle Shaft forward. Seating the c-lock onto the Axle Shaft demands outward pulling until it reaches the counterbore location of the rear axle side gear. After installing the differential pinion shaft through case and pinion apply loctite09 242 to the thread of the differential pinion shaft locking screw for preventing screw loosening before reinstalling. Position the pinion shaft hole against the lock bolt opening before installing a new locking bolt and tightening it to 36 nm (27 ft. Lbs.). Before installation place a gasket on the axle housing cover and fill the opening with axle lubricant up to 3/8 inches above the fill plug opening mark. Replace rear brake drums and rotors if present followed by tires and wheels installation. Afterward lower the vehicle and perform a test drive to verify there are no leaks.