How to replace the front shock absorber assembly on Chevrolet Uplander?

To replace the strut assembly, start by removing the wiper module. Apply ONLY a frame-contact vehicle lift to lift the vehicle without introducing use of suspension-contact lift, raise and support the vehicle. Next, pull the tire and wheel, lower the vehicle, and the strut upper nuts should be removed. Lift the vehicle once more, scribe the strut to the knuckle and pull out the strut lower bolts and nuts to remove the strut. For installation, install first the strut, lower the vehicle, then fasten the strut upper nuts of 41 Nm (30 ft. lbs.). Lift the vehicle back up again to install the strut lower bolts and nuts so that the fastener is clean from any rust and that it brings 3 Nm (27 inch lbs.) of torque/drag against the other before it totally seats; if not, replace the fastener. Adjust the strut to the mark on the knuckle and tighten the strut lower nuts to 123 Nm (90 ft. lbs.). Then install the tire and wheel, lower the vehicle and re-install the wiper module and lastly check the alignment.

How Should the Front Shock Absorber Be Disposed of Safely on Chevrolet Uplander?

To waste suspension strut, provide right eye protection to be safe from drilled metal chips. Clamp the strut in a vise horizontally and the rod is well extended. Use a 5mm (3/16 inch) drill bit to drill a hole through the center of endcap to allow gas or a mixture of gas/oil to escape; avoid spillages of oil within the garage with shop towels. Remove the strut from the vise, and hold it vertically over a drain pan to drain any residual oil over the pan with the hole facing down. Finally move the rod in and out of the tube to ensure that all oil is out of the strut completely.

OEM Chevrolet Uplander Shock Absorber

Suspension Shock Absorber

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Shock Absorbers found

View related parts
Chevrolet Uplander Shock Absorber, Rear Part Number: 19169325
$190.33 MSRP: $369.40
You Save: $179.07 (49%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Absorber Kit, Rear Leveling Shock; Suspension Strut and Shock Assembly; Complete Strut Set.; Shock; Absorber, Shock Absorber Air Lift
- Position: Rear
- Replaces: 22064824, 22064712, 22064876, 22064818, 22064822, 22064847
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005 Chevrolet Uplander | Base, LS, LT | 6 Cyl 3.5 L GAS
View related parts
Chevrolet Uplander Shock Absorber, Rear Part Number: 15926213
$180.75 MSRP: $181.36
You Save: $0.61 (1%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Absorber Assembly-Rear Leveling Shock; Shock; Absorber, Shock Absorber Air Lift
- Position: Rear
- Replaces: 15216493, 15829670
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2008 Chevrolet Uplander | Base, LS, LT | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
View related parts
Chevrolet Uplander Strut Part Number: 88965456
$106.59 MSRP: $200.15
You Save: $93.56 (47%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Strut Assembly, Front Suspension; Complete Suspension Strut and Shock Absorber Kit.; Strut, Front And Rear Suspension
- Position: Front
- Replaces: 88965457
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2008 Chevrolet Uplander | Base, LS, LT | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
View related parts
Chevrolet Uplander Shock Absorber, Rear Part Number: 15219512
Product Specifications
- Other Name: Absorber Assembly-Rear Leveling Shock; Suspension Strut and Shock Kit; Complete Strut.; Shock; Absorber, Shock Absorber Air Lift
- Position: Rear
- Replaces: 10367358, 10315979
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2006 Chevrolet Uplander | Base, LS, LT | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS
View related parts
Chevrolet Uplander Shock Absorber Part Number: 15943270
Product Specifications
- Other Name: Suspension Strut and Shock Absorber Assembly Kit; Complete Strut and Shock Absorber Set.; Shock; Absorber, Front And Rear Suspension
- Position: Rear
- Replaces: 10413405, 10311197, 10288272, 10406050, 10310676, 10318617, 88963482, 10331459, 10401283, 10331458, 10406052, 10401282
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2008 Chevrolet Uplander | Base, LS, LT | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L FLEX, 6 Cyl 3.9 L GAS
View related parts
Chevrolet Uplander Shock Absorber, Rear Part Number: 15219511
Product Specifications
- Other Name: Absorber Assembly-Rear Leveling Shock; Suspension Strut and Shock Kit; Complete Strut.; Shock; Absorber, Shock Absorber Air Lift
- Position: Rear
- Warranty: This genuine part is guaranteed by GM's factory warranty.
Fits the following Vehicles:
- 2005-2006 Chevrolet Uplander | Base, LS, LT | 6 Cyl 3.5 L GAS, 6 Cyl 3.9 L GAS

Chevrolet Uplander Shock Absorber

Want to cut long-term maintenance and repair costs? Choose OEM Shock Absorber. Those parts deliver top durability you can trust. On our site, you'll find a huge catalog of genuine Chevrolet Uplander parts. Prices are unbeatable, so you can keep more in your pocket. Every OEM Chevrolet Uplander Shock Absorber includes a manufacturer's warranty. You can also get an easy return policy that keeps buying risk free. Fast delivery, get your car on the road quickly. It's simple to search, compare, and order. Stop guessing about quality or fit. Order today and save with parts that last.

The Chevrolet Uplander Shock Absorber is a compartment that stabilizes and offers a isolation system in Chevrolet Uplander automobiles known for their endurance and efficiency. Specifically intended to mitigate shock impulses, the Shock Absorber will improve ride comfort as well as control within a vehicle to provide a better driving feel. These shock absorbers are a prime example of hydraulic systems, reducing the extreme movements of the suspension with the help of converting kinetic energy into heat, functioning jointly with springs to counter vibrations. In the Chevrolet Uplander made from the year 2005 to the year 2009, there is the use of shock absorber of some varieties that include the twin tube shock absorbers and the mono tube shock absorbers which have their had unique advantages that cannot be compared. Twin-tube shocks are simple to construct while the mono-tube have better heat transfer and performance rating as well as ability to be installed in any direction. More elaborate types such as Position Sensitive Damping (PSD) as well as Acceleration Sensitive Damping (ASD) extend the Shock Absorber's sensitivity to various driving conditions, thus greatly increasing comfort and control. The Chevrolet Uplander can be matched to other models making it agreeable in providing the optimal solutions for drivers especially as per efficiency and safety we are concerned. By having ABS, independent suspensions, and anti-roll bars, the performance of the Uplander is well-balanced and it does not wobble. This suspension part is a unique and vital component in the Chevrolet Uplander lineup due to its excellent engineering and dedication to improving the car's performance.

Chevrolet Uplander Shock Absorber Parts and Q&A

Strut
88965456
Q: How to replace the front shock absorber assembly on Chevrolet Uplander?
A:
To replace the strut assembly, start by removing the wiper module. Apply ONLY a frame-contact vehicle lift to lift the vehicle without introducing use of suspension-contact lift, raise and support the vehicle. Next, pull the tire and wheel, lower the vehicle, and the strut upper nuts should be removed. Lift the vehicle once more, scribe the strut to the knuckle and pull out the strut lower bolts and nuts to remove the strut. For installation, install first the strut, lower the vehicle, then fasten the strut upper nuts of 41 Nm (30 ft. lbs.). Lift the vehicle back up again to install the strut lower bolts and nuts so that the fastener is clean from any rust and that it brings 3 Nm (27 inch lbs.) of torque/drag against the other before it totally seats; if not, replace the fastener. Adjust the strut to the mark on the knuckle and tighten the strut lower nuts to 123 Nm (90 ft. lbs.). Then install the tire and wheel, lower the vehicle and re-install the wiper module and lastly check the alignment.
Shock Absorber
15943270
Q: How Should the Front Shock Absorber Be Disposed of Safely on Chevrolet Uplander?
A:
To waste suspension strut, provide right eye protection to be safe from drilled metal chips. Clamp the strut in a vise horizontally and the rod is well extended. Use a 5mm (3/16 inch) drill bit to drill a hole through the center of endcap to allow gas or a mixture of gas/oil to escape; avoid spillages of oil within the garage with shop towels. Remove the strut from the vise, and hold it vertically over a drain pan to drain any residual oil over the pan with the hole facing down. Finally move the rod in and out of the tube to ensure that all oil is out of the strut completely.